Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C146C  Open in ABS Motor Relay Circuit  


DESCRIPTION

The ABS motor relay supplies power to the pump motor. While the ABS is activated, the skid control ECU turns the ABS motor relay on to operate the pump motor.

If the voltage supplied to the ABS motor relay (+BM) is too low due to low voltage from the battery or alternator, this DTC may be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C146C Open in ABS Motor Relay Circuit Any of the following is detected:
1.

When the ABS motor relay is actuated, voltage is not supplied to the pump motor.

2.

When the ABS motor relay is not actuated, voltage in the pump motor is high.

3.

The skid control ECU judges that pump motor operation is abnormal.


·

ABS NO. 1 fuse

·

ABS motor relay circuit

·

ABS motor relay (brake actuator assembly)



WIRING DIAGRAM

C313363E02
5.25,4.563 6.125,4.813 0.875,0.25 10 false Pump Motor 3.802,3.323 4.323,3.51 0.521,0.188 10 false GND2 3.521,3.063 3.813,3.229 0.292,0.167 10 false 13 4.792,5.021 6.458,5.219 1.667,0.198 10 false Brake Actuator Assembly 4.427,5.031 4.823,5.229 0.396,0.198 10 false A35 4.906,2.344 6.094,2.594 1.188,0.25 10 false Skid Control ECU 4.896,1.094 6.042,1.344 1.146,0.25 10 false ABS Motor Relay 3.823,1.365 4.24,1.615 0.417,0.25 10 false +BM 3.573,1.104 3.771,1.292 0.198,0.188 10 false 1 2.354,1.094 2.677,1.302 0.323,0.208 10 false 2 1.948,1.094 2.188,1.281 0.24,0.188 10 false 1 1.823,1.406 2.594,1.656 0.771,0.25 10 false ABS NO. 1 0.76,2.448 1.156,2.635 0.396,0.188 10 false ALT 0.885,3.948 1.438,4.135 0.552,0.188 10 false Battery 0.76,1.719 1.531,1.969 0.771,0.25 10 false F/B ALT 0.76,3.208 1.531,3.458 0.771,0.25 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

When C1241 and/or C1417 is output together with C146C, inspect and repair the trouble areas indicated by C1241 and/or C1417 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1241 for C1241 and/or Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1417 for C1417).


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ABS MOTOR RELAY)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Active Test using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Motor Relay ABS motor relay Relay ON/OFF Operating sound of motor can be heard


d.

Check the operating sound of the pump motor when operating it using the GTS.


Result:
Result Proceed to
Operating sound is heard. A
Operating sound is not heard. B



A

2.RECONFIRM DTC

B

3.CHECK HARNESS AND CONNECTOR (+BM TERMINAL)
2.RECONFIRM DTC
HINT:

This DTC is stored when a problem is identified in the skid control ECU (brake actuator assembly).

The ABS motor relay is in the skid control ECU (brake actuator assembly).

Therefore, motor relay inspection and motor relay unit inspection cannot be performed. Be sure to check if the DTC is output again before replacing the skid control ECU (brake actuator assembly).


a.

Turn the engine switch off.



c.

Turn the engine switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for 30 seconds or more.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C146C is not output. A
DTC C146C is output. B


HINT:
·

If a speed signal of 40 km/h (25 mph) or more is received by the skid control ECU (brake actuator assembly) with the engine switch on (IG), the skid control ECU (brake actuator assembly) performs self diagnosis of the motor circuit.

·

If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly).

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.





A

B

3.CHECK HARNESS AND CONNECTOR (+BM TERMINAL)
a.
U189565E01
0.274,0.178 0.472,0.334 0.198,0.156 10 *a 0.291,0.78 0.586,0.936 0.295,0.156 10 A35 1.133,2.623 0.796,1.885 false 1.164,2.619 1.524,2.775 0.361,0.156 10 +BM

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-1 (+BM) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

4.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.
U189566E01
0.274,0.178 0.472,0.334 0.198,0.156 10 *a 0.291,0.78 0.586,0.936 0.295,0.156 10 A35 2.57,2.623 2.788,1.873 false 2.156,2.664 2.583,2.820 0.427,0.156 10 GND2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-13 (GND2) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)