Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059587 METER / GAUGE / DISPLAY _0292197 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

The combination meter sub-assembly uses the fuel sender gauge assembly to determine the level of the fuel in the fuel tank. The resistance of the fuel sender gauge assembly will vary between approximately 15 Ω with the float at the full position, and 410 Ω with the float at the empty position. The combination meter sub-assembly outputs battery voltage through two resistors that are mounted inside the combination meter sub-assembly. The combination meter sub-assembly measures the voltage between the variable resistor in the fuel sender gauge and the two resistors mounted in the meter. Voltage measured at this point will vary as the float of the fuel sender gauge is moved. The highest voltage observed should be approximately half of the battery voltage.


HINT:

The fuel level warning light will come on when the fuel level is below 9.8 liters (10.4 US qts, 8.6 Imp. qts).


WIRING DIAGRAM

E230580E49
5.385,3.104 6.552,3.51 1.167,0.406 10 false Combination Meter Sub-assembly 5.719,0.979 5.99,1.135 0.271,0.156 10 false L 5.719,2.344 6.125,2.5 0.406,0.156 10 false FE 5.479,0.885 5.938,1.271 0.458,0.385 10 false 27 5.469,2.24 5.823,2.583 0.354,0.344 10 false 30 2.323,2.229 2.51,2.427 0.188,0.198 10 false 2 2.323,0.885 2.521,1.083 0.198,0.198 10 false 1 0.375,3.104 2.448,3.49 2.073,0.385 10 false Fuel Suction Tube with Pump and Gauge Assembly 0.781,1.448 1.417,2.24 0.635,0.792 10 false Fuel Sender Gauge Assembly 5.385,2.938 5.896,3.271 0.51,0.333 10 false G28 0.375,2.948 1.052,3.302 0.677,0.354 10 false M17 1.698,2.01 1.917,2.26 0.219,0.25 10 false 1 1.688,1.354 1.802,1.5 0.115,0.146 10 false 2 0.802,1.271 0.917,1.417 0.115,0.146 10 false A

PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
w/o Multi-information Display A
w/ Multi-information Display B




A

2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)

B

3.READ VALUE USING GTS (FUEL INPUT)
2.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge Sender E / Empty / Warning / 1/4 / 1/2 / 3/4 / Full / Sender F Value selected during ACTIVE TEST is displayed

OK:

Fuel receiver gauge indication is normal.




OK

3.READ VALUE USING GTS (FUEL INPUT)

NG

REPLACE COMBINATION METER SUB-ASSEMBLY

3.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel input / Min.: 0 L, Max.: 127.5 L
w/ Multi-information Display:

Fuel receiver gauge indicates F: 59.6 L

Fuel receiver gauge indicates 3/4: 50.1 L

Fuel receiver gauge indicates 1/2: 35.9 L

Fuel receiver gauge indicates 1/4: 21.6 L

Fuel receiver gauge indicates E: 6.5 L


w/o Multi-information Display:

Fuel receiver gauge indicates F: 58.5 L

Fuel receiver gauge indicates 1/2: 32.5 L

Fuel receiver gauge indicates E: 6.5 L


-

Result:
Result Proceed to
Fuel level data displayed on the GTS is almost the same as the fuel receiver gauge indication. A
Fuel level data displayed on the GTS differs from the fuel receiver gauge indication. B




A

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)

B

REPLACE COMBINATION METER SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)
a.

Disconnect the G28 combination meter sub-assembly connector.


b.

Disconnect the M17 fuel suction tube with pump and gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G28-27 (L) - M17-1 Always Below 1 Ω
G28-27 (L) or M17-1 - Body ground Always 10 kΩ or higher
G28-30 (FE) - M17-2 Always Below 1 Ω
G28-30 (FE) or M17-2 - Body ground Always 10 kΩ or higher




OK

5.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FUEL SENDER GAUGE ASSEMBLY
E350006E02
0.458,4.198 1.583,4.198 false 0.5,2.583 1.521,2.583 false 0.365,2.5 0.76,2.771 0.396,0.271 10 false F 0.302,4.115 0.698,4.385 0.396,0.271 10 false E 0.135,0.125 0.531,0.396 0.396,0.271 10 false *a

a.

Remove the fuel sender gauge assembly (see page Engine / Hybrid System>2AZ-FE FUEL>FUEL PUMP>REMOVAL for 2AZ-FE, see page Engine / Hybrid System>2GR-FE FUEL>FUEL PUMP>DISASSEMBLY for 2GR-FE).


b.

Check that the float moves smoothly between E and F.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Float level is F (upper) 13.5 to 16.5 Ω
1 - 2 Float level is between F (upper) and E (lower) 13.5 to 414.5 Ω (Gradually changes)
1 - 2 Float level is E (lower) 405.5 to 414.5 Ω


Text in Illustration
*a Front view of wire harness connector
(to Fuel Sender Gauge Assembly)

Result:
Result Proceed to
OK A
NG (for 2AZ-FE) B
NG (for 2GR-FE) C




A

6.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

B

REPLACE FUEL SENDER GAUGE ASSEMBLY

C

REPLACE FUEL SENDER GAUGE ASSEMBLY

6.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
U190001E02
0.531,1.271 0.969,1.469 0.438,0.198 10 false M17 0.604,3.531 1.042,3.729 0.438,0.198 10 false A 0.281,0.167 0.719,0.365 0.438,0.198 10 false *a

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M17-1 - A-2 Always Below 1 Ω
M17-2 - A-1 Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)

Result:
Result Proceed to
OK A
NG (for 2AZ-FE) B
NG (for 2GR-FE) C




A

REPLACE COMBINATION METER SUB-ASSEMBLY

B

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

C

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY