Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059587 METER / GAUGE / DISPLAY _0292197 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter sub-assembly detects a fuel sender gauge assembly malfunction via a direct line.

DTC No. DTC Detection Condition Trouble Area Note
B1500 When IG voltage is 9.5 V or more and the following condition is detected:
·

Average input signal of fuel sender gauge assembly is 630 Ω or more 3 times consecutively


·

Harness or connector

·

Fuel sender gauge assembly

·

Fuel suction tube with pump and gauge assembly

·

Combination meter sub-assembly


w/ Multi-information Display

WIRING DIAGRAM

E230580E49
5.385,3.104 6.552,3.51 1.167,0.406 10 false Combination Meter Sub-assembly 5.719,0.979 5.99,1.135 0.271,0.156 10 false L 5.719,2.344 6.125,2.5 0.406,0.156 10 false FE 5.479,0.885 5.938,1.271 0.458,0.385 10 false 27 5.469,2.24 5.823,2.583 0.354,0.344 10 false 30 2.323,2.229 2.51,2.427 0.188,0.198 10 false 2 2.323,0.885 2.521,1.083 0.198,0.198 10 false 1 0.375,3.104 2.448,3.49 2.073,0.385 10 false Fuel Suction Tube with Pump and Gauge Assembly 0.781,1.448 1.417,2.24 0.635,0.792 10 false Fuel Sender Gauge Assembly 5.385,2.938 5.896,3.271 0.51,0.333 10 false G28 0.375,2.948 1.052,3.302 0.677,0.354 10 false M17 1.698,2.01 1.917,2.26 0.219,0.25 10 false 1 1.688,1.354 1.802,1.5 0.115,0.146 10 false 2 0.802,1.271 0.917,1.417 0.115,0.146 10 false A

PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel input/Min.: 0 L, Max.: 127.5 L
w/ Multi-information Display:

Fuel receiver gauge indicates F: 59.6 L

Fuel receiver gauge indicates 3/4: 50.1 L

Fuel receiver gauge indicates 1/2: 35.9 L

Fuel receiver gauge indicates 1/4: 21.6 L

Fuel receiver gauge indicates E: 6.5 L


w/o Multi-information Display:

Fuel receiver gauge indicates F: 58.5 L

Fuel receiver gauge indicates 1/2: 32.5 L

Fuel receiver gauge indicates E: 6.5 L


Unit: Liter

Result:
Result Proceed to
Fuel level data cannot be displayed on the GTS. A
Fuel level data can be displayed on the GTS and DTC B1500 is output. B




A

2.INSPECT FUEL SENDER GAUGE ASSEMBLY

B

REPLACE COMBINATION METER SUB-ASSEMBLY

2.INSPECT FUEL SENDER GAUGE ASSEMBLY
U189961E01
0.813,1.115 1.149,1.278 0.336,0.163 10 G28 1.012,2.953 1.321,2.57 false 0.929,2.97 1.067,3.133 0.138,0.163 10 L 2.024,2.969 1.672,2.566 false 2.063,2.976 2.297,3.139 0.234,0.163 10 FE 0.243,0.213 0.483,0.375 0.240,0.163 10 *a

a.

Disconnect the G28 combination meter sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G28-27 (L) - G28-30 (FE) Always 13.5 to 414.5 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Sub-assembly)



OK

REPLACE COMBINATION METER SUB-ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)
a.

Disconnect the M17 fuel suction tube with pump and gauge assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G28-27 (L) - M17-1 Always Below 1 Ω
G28-27 (L) or M17-1 - Body ground Always 10 kΩ or higher
G28-30 (FE) - M17-2 Always Below 1 Ω
G28-30 (FE) or M17-2 - Body ground Always 10 kΩ or higher




OK

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FUEL SENDER GAUGE ASSEMBLY
E350006E02
0.458,4.198 1.583,4.198 false 0.5,2.583 1.521,2.583 false 0.365,2.5 0.76,2.771 0.396,0.271 10 false F 0.302,4.115 0.698,4.385 0.396,0.271 10 false E 0.135,0.125 0.531,0.396 0.396,0.271 10 false *a

a.

Remove the fuel sender gauge assembly (see page Engine / Hybrid System>2AZ-FE FUEL>FUEL PUMP>REMOVAL for 2AZ-FE, see page Engine / Hybrid System>2GR-FE FUEL>FUEL PUMP>DISASSEMBLY for 2GR-FE).


b.

Check that the float moves smoothly between E and F.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Float level is F (upper) 13.5 to 16.5 Ω
1 - 2 Float level is between F (upper) and E (lower) 13.5 to 414.5 Ω (Gradually changes)
1 - 2 Float level is E (lower) 405.5 to 414.5 Ω


Text in Illustration
*a Front view of wire harness connector
(to Fuel Sender Gauge Assembly)

Result:
Result Proceed to
OK A
NG (for 2AZ-FE) B
NG (for 2GR-FE) C




A

5.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

B

REPLACE FUEL SENDER GAUGE ASSEMBLY

C

REPLACE FUEL SENDER GAUGE ASSEMBLY

5.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
U190001E02
0.531,1.271 0.969,1.469 0.438,0.198 10 false M17 0.604,3.531 1.042,3.729 0.438,0.198 10 false A 0.281,0.167 0.719,0.365 0.438,0.198 10 false *a

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M17-1 - A-2 Always Below 1 Ω
M17-2 - A-1 Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)

Result:
Result Proceed to
OK A
NG (for 2AZ-FE) B
NG (for 2GR-FE) C




A

REPLACE COMBINATION METER SUB-ASSEMBLY

B

REPLACE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

C

REPLACE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE