Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2013.04–2016.05
RM24M0E _56 Audio / Visual / Telematics _059588 NAVIGATION / MULTI INFO DISPLAY _0292199 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the navigation receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the navigation receiver assembly cannot be operated using the steering pad switch assembly, and also the navigation receiver assembly itself cannot function.

WIRING DIAGRAM

E230084E22
0.323,1.156 0.875,1.333 0.552,0.177 10 false Volume- 2.5,4 3.083,4.177 0.583,0.177 10 false Off hook 3.292,4 3.729,4.177 0.438,0.177 10 false Voice 1.125,5.031 3.063,5.208 1.938,0.177 10 false Steering Pad Switch Assembly 1.698,4 2.271,4.177 0.573,0.177 10 false On hook 1.104,1.156 1.698,1.333 0.594,0.177 10 false Volume+ 4.938,0.552 5.229,0.729 0.292,0.177 10 false AU1 4.938,1.521 5.24,1.698 0.302,0.177 10 false EAU 4.948,2.458 5.24,2.635 0.292,0.177 10 false AU2 6.24,0.646 6.615,0.823 0.375,0.177 10 false SW1 6.26,1.583 6.646,1.76 0.385,0.177 10 false SWG 6.24,2.552 6.615,2.729 0.375,0.177 10 false SW2 5.719,4.885 6.094,5.063 0.375,0.177 10 false F17 1.938,1.156 2.406,1.333 0.469,0.177 10 false Seek- 4.51,0.688 4.698,0.865 0.188,0.177 10 false j1 4.521,1.656 4.708,1.833 0.188,0.177 10 false j1 4.521,2.594 4.708,2.771 0.188,0.177 10 false j1 4.5,0.469 4.677,0.646 0.177,0.177 10 false 10 4.531,1.438 4.625,1.615 0.094,0.177 10 false 8 4.531,2.375 4.625,2.552 0.094,0.177 10 false 9 5.448,0.708 5.74,0.885 0.292,0.177 10 false G10 5.448,1.656 5.74,1.833 0.292,0.177 10 false G10 5.458,2.604 5.74,2.781 0.281,0.177 10 false G10 6,0.563 6.177,0.74 0.177,0.177 10 false 21 6.01,1.5 6.188,1.677 0.177,0.177 10 false 23 6,2.469 6.177,2.646 0.177,0.177 10 false 22 5.552,1.438 5.646,1.615 0.094,0.177 10 false 4 5.542,0.469 5.635,0.646 0.094,0.177 10 false 6 5.552,2.375 5.646,2.552 0.094,0.177 10 false 5 2.552,2.083 2.99,2.26 0.438,0.177 10 false MODE 4.688,3.125 5.583,3.448 0.896,0.323 10 false Spiral Cable Sub-assembly 5.708,5.052 6.979,5.427 1.271,0.375 10 false Navigation Receiver Assembly 2.563,1.156 3.031,1.333 0.469,0.177 10 false Seek+

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
a.

Disconnect the F17 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F17-21 (SW1) - F17-23 (SWG) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 323 to 335 Ω
Volume+ switch pushed 980 to 1020 Ω
Volume- switch pushed 3048 to 3172 Ω
F17-22 (SW2) - F17-23 (SWG) No switch pushed 95 to 105 kΩ
MODE switch pushed Below 2.5 Ω
On hook switch pushed 323 to 335 Ω
Off hook switch pushed 980 to 1020 Ω
Voice switch pushed 3048 to 3172 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Disconnect the j1 steering pad switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

U189962E02
4.313,0.823 4.073,1.156 false 4.427,0.833 4.427,1.177 false 4.521,0.813 4.802,1.094 false 1.021,1.563 0.646,0.927 0.646,0.927 0.469,0.927 false 1.375,1.531 1.719,0.844 1.719,0.844 1.896,0.844 false 0.906,1.833 0.24,1.833 false 1.417,1.844 2.115,1.844 false 0.896,2.177 0.438,2.604 0.438,2.604 0.271,2.604 false 6.125,1.594 6.74,1.594 false 6.313,2.083 6.875,2.083 false 5.792,1.531 6.104,0.823 6.104,0.823 6.271,0.823 false 3.885,1.167 4.198,1.313 0.313,0.146 10 false EAU 4.302,1.188 4.594,1.333 0.292,0.146 10 false AU2 4.792,1.115 5.083,1.26 0.292,0.146 10 false AU1 4.854,0.521 5.063,0.677 0.208,0.156 10 false j1 0.073,0.021 0.26,0.208 0.188,0.188 10 false *a 0.292,0.844 0.49,1.042 0.198,0.198 10 false *c 1.948,0.76 2.167,0.979 0.219,0.219 10 false *b 0.063,1.729 0.229,1.896 0.167,0.167 10 false *e 2.156,1.76 2.333,1.938 0.177,0.177 10 false *d 0.083,2.531 0.26,2.729 0.177,0.198 10 false *f 6.781,1.5 6.979,1.729 0.198,0.229 10 false *g 6.302,0.75 6.469,0.938 0.167,0.188 10 false *h 6.917,2 7.115,2.229 0.198,0.229 10 false *i

Standard Resistance:
Tester Connection Condition Specified Condition
j1-10 (AU1) - j1-8 (EAU) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 313 to 345 Ω
Volume+ switch pushed 980 to 1020 Ω
Volume- switch pushed 2955 to 3265 Ω
j1-9 (AU2) - j1-8 (EAU) No switch pushed 95 to 105 kΩ
MODE switch pushed Below 2.5 Ω
On hook switch pushed 313 to 345 Ω
Off hook switch pushed 980 to 1020 Ω
Voice switch pushed 2955 to 3265 Ω


Text in Illustration
*a Component without harness connected
(Steering Pad Switch Assembly)
*b Volume+
*c Volume- *d Seek+
*e Seek- *f MODE
*g On hook *h Off hook
*i Voice - -



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Disconnect the j1 steering pad switch assembly connector.


b.

Disconnect the G10 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

E356085E04
1.292,0.75 1.708,1 0.417,0.25 5.469,1.25 5.885,1.5 0.417,0.25 1.01,1.26 1.396,1.563 false 1.542,1.563 2,1.365 false 5.854,1.875 6.167,1.406 false 5.208,2.083 5.708,1.906 false 1.01,1.583 1.25,1.583 false 5.979,1.896 6.188,1.969 false 0.135,0.115 0.573,0.396 0.438,0.281 10 false *a 1.448,0.781 1.76,0.979 0.313,0.198 10 false j1 0.688,1.156 1.021,1.354 0.333,0.198 10 false AU2 2.052,1.26 2.365,1.458 0.313,0.198 10 false EAU 5.552,1.292 5.865,1.49 0.313,0.198 10 false G10 4.875,2.01 5.188,2.208 0.313,0.198 10 false EAU 0.729,0.74 1.167,1.021 0.438,0.281 10 false *b 4.875,1.208 5.313,1.49 0.438,0.281 10 false *c 0.688,1.5 1.021,1.698 0.333,0.198 10 false AU1 6.208,1.323 6.542,1.521 0.333,0.198 10 false AU2 6.229,1.906 6.563,2.104 0.333,0.198 10 false AU1

Standard Resistance:
Tester Connection Condition Specified Condition
j1-8 (EAU) - G10-4 (EAU) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
j1-10 (AU1) - G10-6 (AU1) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
j1-9 (AU2) - G10-5 (AU2) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right



d.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j1-8 (EAU) - G10-4 (EAU) Always Below 1 Ω
j1-10 (AU1) - G10-6 (AU1) Always Below 1 Ω
j1-9 (AU2) - G10-5 (AU2) Always Below 1 Ω


NOTICE:
·

The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



HINT:


Text in Illustration
*a Component without harness connected
(Spiral Cable Sub-assembly)
*b Steering Pad Switch Assembly Side
*c Vehicle Side



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY