55312
1.INSTALL INSTRUMENT PANEL LOWER
Install the 3 bolts, 11 screws and 4 nuts to install the instrument panel lower.
Connect each connector and each clamp.
86860
2.INSTALL NAVIGATION ANTENNA ASSEMBLY
55400
3.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (w/o Knee Airbag)
Install the instrument panel safety pad assembly with the bolt.
33560
4.INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY
for U660E (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT LEVER>INSTALLATION)
for U241E (See page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT LEVER>INSTALLATION)
for K112 (See page Drivetrain>K112 (CVT)>SHIFT LEVER>INSTALLATION)
33820B
5.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
for U660E (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT LEVER>INSTALLATION)
for U241E (See page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT LEVER>INSTALLATION)
for K112 (See page Drivetrain>K112 (CVT)>SHIFT LEVER>INSTALLATION)
55900A
6.INSTALL HEATER CONTROL AND ACCESSORY
Connect each connector.
Engage the 6 claws to install the heater control and accessory.
55433B
7.INSTALL NO. 2 INSTRUMENT PANEL FINISH PANEL LOWER
Engage the 4 claws to install the No. 2 instrument panel finish panel lower.
55434B
8.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER
Engage the 3 clamps and 9 claws to install the instrument panel finish panel lower center.
Install the bolt.
58534E
9.INSTALL FLOOR CARPET COVER CENTER LH
Engage the 2 claws.
Install the floor carpet cover center LH with the 2 clips.
58533C
10.INSTALL FLOOR CARPET COVER CENTER RH
Engage the 5 claws and clamp and install the floor carpet cover center RH.
55432B
11.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER (w/ Knee Airbag)
Connect each connector.
Install the duct to the room temperature sensor.
Connect the hood lock control lever cable and fuel lid open lever cable.
Engage the 13 claws.
Install the instrument panel finish panel lower with the 3 bolts.
55432B
12.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER (w/o Knee Airbag)
Connect the connector.
Install the duct to the room temperature sensor.
Connect the hood lock control lever cable and fuel lid open lever cable.
Engage the 8 claws.
Install the instrument panel finish panel lower with the 3 bolts.
55606
13.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Engage the guide and 2 claws.
Install the No. 1 instrument panel under cover sub-assembly with the screw.
55447C
14.INSTALL NO. 1 SWITCH HOLE BASE
Connect each connector.
Engage the 5 claws to install the No. 1 switch hole base.
55474B
15.INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH
Connect the connector.
Engage the 13 claws to install the instrument cluster finish panel garnish.
89340A
16.INSTALL CLEARANCE WARNING ECU ASSEMBLY (w/ Clearance Sonar)
55550
17.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
Position the glove compartment door assembly horizontally and engage the 2 hinges.
Engaging the hinges from above causes the hinges to be deformed. Be sure to install the glove compartment door horizontally.
Bend parts A and B in the directions indicated by the arrows in the illustration to engage the 2 stoppers.
Engage the claw of the glove compartment door stopper to connect the glove compartment door stopper, and install the glove compartment door assembly.
55607
18.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Engage the 2 claws and 2 guides to install the No. 2 instrument panel under cover sub-assembly.
62112
19.INSTALL COWL SIDE TRIM BOARD LH
62111C
20.INSTALL COWL SIDE TRIM BOARD RH
67914B
21.INSTALL FRONT DOOR SCUFF PLATE LH
67913B
22.INSTALL FRONT DOOR SCUFF PLATE RH
33504F
23.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.
55302A
24.INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY
83100
25.INSTALL COMBINATION METER ASSEMBLY
28800
26.CONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
27.CHECK SRS WARNING LIGHT
28800
28.PERFORM INITIALIZATION
(See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)
Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.