P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)
Diagnostic trouble codes · Vehicles built Dec 2007 – Jul 2009
Also covers:
- P2A03 A/F Sensor Circuit Slow Response (Bank 2 Sensor 1)
Versions by build date: Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010
CAUTION / NOTICE / HINT
DESCRIPTION
- HINT:
- DTC P2A00 indicates malfunctions related to the bank 1 A/F sensor.
- DTC P2A03 indicates malfunctions related to the bank 2 A/F sensor.
- Bank 1 refers to the bank that includes cylinder No. 1.
- Bank 2 refers to the bank that includes cylinder No. 2.
- Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
- DTC P2A00 indicates malfunctions related to the bank 1 A/F sensor.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P2A00 P2A03 |
Calculated value for air fuel ratio (A/F) sensor response rate deterioration level is less than threshold (2 trip detection logic) |
|
MONITOR DESCRIPTION
After engine is warmed up, the ECM performs air-fuel ratio feedback control to maintain the air-fuel ratio at the stoichiometric level. In addition, active A/F control is performed for approximately 10 seconds after preconditions are met in order to measure the A/F sensor response rate. During active A/F control, the ECM forcibly increases and decreases the injection volume a certain amount, based on the stoichiometric air-fuel ratio learned during normal air-fuel ratio control, and measures the A/F sensor response rate. The ECM receives a signal from the A/F sensor while performing active A/F control and uses it to calculate the A/F sensor response rate deterioration level.If the value for A/F sensor response rate deterioration level is less than the threshold, the ECM interprets this as a malfunction and stores the DTC.


CONFIRMATION DRIVING PATTERN
- HINT:
- Performing this confirmation pattern will activate the A/F sensor response monitor.
-


- Connect the intelligent tester to the DLC3.
- Turn the ignition switch to ON.
- Turn the tester ON.
- Clear DTCs (Click here).
- Switch the ECM from normal mode to check mode (Click here).
- Enter the following menus: Powertrain / Engine and ECT / Data List / O2S(A/FS) Monitor.
- Check that the item O2S(A/FS) Monitor displays Incmpl.
- Start the engine and warm it up 'Proceed to "A").
- Drive the vehicle at between 40 km/h and 120 km/h (25 mph and 75 mph) for 3 minutes. However, the vehicle should be driven at a constant speed.
- Note the state of the Data List items. Those items will change to Compl as the O2 Sensor monitor operates.
- Enter the following menus: Powertrain / Engine and ECT / DTC and check if any DTCs (any pending DTCs) are output.
- HINT:
- If the item O2S (A/FS) Monitor does not change to Compl, and any pending DTCs fail to output, extend the driving time.
WIRING DIAGRAM
Refer to DTC P2195 (Click here).INSPECTION PROCEDURE
- HINT:
- Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
- The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.
- (1) Connect the intelligent tester to the DLC3.
- (2) Start the engine and turn the tester ON.
- (3) Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
- (4) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
- (5) Perform the Control the Injection Volume for A/F sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
- (6) Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.
- (1) Connect the intelligent tester to the DLC3.
- HINT:
- The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
- Standard:
Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS B1S1 or AFS B2S1
(A/F)
+25%
Rich
Less than 3.0 V
AFS B1S1 or AFS B2S1
(A/F)
-12.5%
Lean
More than 3.35 V
O2S B1S2 or O2S B2S2
(HO2)
+25%
Rich
More than 0.55 V
O2S B1S2 or O2S B2S2
(HO2)
-12.5%
Lean
Less than 0.4 V
- The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- NOTICE:
- The Air Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.
| Case |
A/F Sensor (Sensor 1) Output Voltage |
HO2 Sensor (Sensor 2) Output Voltage |
Main Suspected Trouble Area |
| 1 |
![]() ![]() ![]() ![]() |
![]() ![]() ![]() ![]() |
- |
| 2 |
![]() ![]() ![]() ![]() |
![]() ![]() ![]() ![]() |
|
| 3 |
![]() ![]() ![]() ![]() |
![]() ![]() ![]() ![]() |
|
| 4 |
![]() ![]() ![]() ![]() |
![]() ![]() ![]() ![]() |
|
- To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor / A/F Control System / AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2, then press View button.
- Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
- HINT:
- DTC P2A00 or P2A03 may be also stored, when the air-fuel ratio is stuck rich or lean.
- A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
- A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
- Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- DTC P2A00 or P2A03 may be also stored, when the air-fuel ratio is stuck rich or lean.
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00 AND/OR P2A03) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
Result Result
Proceed to
P2A00 and/or P2A03
A
P2A00 and/or P2A03 and other DTCs
B
- HINT:
- If any DTCs other than P2A00 or P2A03 are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() ![]() |
Disconnect the B33*1 or B31*2 A/F sensor connector.
- HINT:
- *1: Bank 1 Sensor 1
- *2: Bank 2 Sensor 1
- *1: Bank 1 Sensor 1
Measure the resistance between the terminals of the A/F sensor connector.
- Standard Resistance (Bank 1 Sensor 1):
Tester Connections
Specified Conditions
HA1A (1) - +B (2)
1.8 to 3.4 Ω at 20°C (68°F)
HA1A (1) - A1A- (4)
10 kΩ or higher
- Standard Resistance (Bank 2 Sensor 1):
Tester Connections
Specified Conditions
HA2A (1) - +B (2)
1.8 to 3.4 Ω at 20°C (68°F)
HA2A (1) - A2A- (4)
10 kΩ or higher
Reconnect the A/F sensor connector.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() ![]() |
Disconnect the A/F sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B33-2 (+B) - Body ground
Ignition switch ON
11 to 14 V
B31-2 (+B) - Body ground
Ignition switch ON
11 to 14 V
Turn the ignition switch off.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B33-1 (HA1A) - B2-2 (HA1A)
Always
Below 1 Ω
B33-3 (A1A+) - B2-22 (A1A+)
Always
Below 1 Ω
B33-4 (A1A-) - B2-30 (A1A-)
Always
Below 1 Ω
B31-1 (HA2A) - B2-1 (HA2A)
Always
Below 1 Ω
B31-3 (A2A+) - B2-23 (A2A+)
Always
Below 1 Ω
B31-4 (A2A-) - B2-31 (A2A-)
Always
Below 1 Ω
B33-1 (HA1A) or B2-2 (HA1A) - Body ground
Always
10 kΩ or higher
B33-3 (A1A+) or B2-22 (A1A+) - Body ground
Always
10 kΩ or higher
B33-4 (A1A-) or B2-30 (A1A-) - Body ground
Always
10 kΩ or higher
B31-1 (HA2A) or B2-1 (HA2A) - Body ground
Always
10 kΩ or higher
B31-3 (A2A+) or B2-23 (A2A+) - Body ground
Always
10 kΩ or higher
B31-4 (A2A-) or B2-31 (A2A-) - Body ground
Always
10 kΩ or higher
Reconnect the ECM connector.
Reconnect the A/F sensor connector.


|
|
||||
| OK | |
| 4. PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 5. CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read DTCs.
Result Result
Proceed to
P2A00 and/or P2A03
A
No output
B
|
|
||||
| A | |
| 6. REPLACE AIR FUEL RATIO SENSOR |
| NEXT | |
| 7. PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 8. CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read DTCs.
Result Result
Proceed to
No output
A
P2A00 and/or P2A03
B
|
|
||||
| A | ||
| ||






