P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)
Diagnostic trouble codes · Vehicles built Dec 2007 – Jul 2009
Also covers:
- P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)
- P2197 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1)
- P2198 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1)
Versions by build date: Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010
CAUTION / NOTICE / HINT
DESCRIPTION
- HINT:
- Although the DTC titles say oxygen sensor, these DTCs relate to the Air Fuel Ratio (A/F) sensor.
- Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
- Although the DTC titles say oxygen sensor, these DTCs relate to the Air Fuel Ratio (A/F) sensor.
The A/F sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte though the alumina, therefore the sensor activation is accelerated.
In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.
*: Value changes inside the ECM. Since the A/F sensor is the current output element, a current is converted in to a voltage inside the ECM. Any measurements taken at the A/F sensor or ECM connectors will show a constant voltage.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P2195 P2197 |
Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic)
|
|
| While fuel cut operation performed (during vehicle deceleration), air fuel ratio (A/F) sensor current 3.6 mA or more for 3 seconds (2 trip detection logic) |
|
|
| P2196 P2198 |
Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic)
|
|
| While fuel cut operation performed (during vehicle deceleration), air fuel ratio (A/F) sensor current less than 1.4 mA for 3 seconds (2 trip detection logic) |
|
- HINT:
- DTCs P2195 and P2196 indicate malfunctions related to bank 1 A/F sensor circuit.
- DTCs P2197 and P2198 indicate malfunctions related to bank 2 A/F sensor circuit.
- Bank 1 refers to the bank that includes cylinder No. 1.
- Bank 2 refers to the bank that includes cylinder No. 2.
- When any of these DTCs are output, check the A/F sensor voltage output by entering the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / AFS B1S1 or AFS B2S1.
- Short-term fuel trim values can also be read using the intelligent tester.
- The ECM regulates the voltages at the A1A+, A2A+, A1A- and A2A- terminals of the ECM to a constant level. Therefore, the A/F sensor voltage output cannot be confirmed without using the intelligent tester.
- If a A/F sensor malfunction is detected, the ECM stores a DTC.
- DTCs P2195 and P2196 indicate malfunctions related to bank 1 A/F sensor circuit.
MONITOR DESCRIPTION
- Sensor voltage detection monitor
Under the air-fuel ratio feedback control, if the A/F sensor voltage output indicates rich or lean for a certain period of time, the ECM determines that there is a malfunction in the A/F sensor. The ECM illuminates the MIL and stores a DTC.
Example:
If the A/F sensor voltage output is less than 2.8 V (very rich condition) and HO2 sensor output voltage falls from 0.59 V or more to less than 0.21 V for 5 seconds, the ECM stores DTC P2196 or P2198. Alternatively, if the A/F sensor voltage output is more than 3.8 V (very lean condition) and HO2 sensor output voltage rises from less than 0.21 V to 0.59 V or more for 5 seconds, DTC P2195 or P2197 is stored.
- Sensor current detection monitor
A rich air-fuel mixture causes a low A/F sensor current, and a lean air-fuel mixture causes a high A/F sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the A/F sensor current during fuel cut and detects any abnormal current values.
If the A/F sensor output is 3.6 mA or more for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the A/F sensor and stores DTC P2195 or P2197 (high-side stuck). If the A/F sensor output is less than 1.4mA for more than 3 seconds of cumulative time, the ECM stores DTC P2196 or P2198 (low-side stuck).


WIRING DIAGRAM


CONFIRMATION DRIVING PATTERN
- CAUTION:
- Strictly observe posted speed limits, traffic laws, and road conditions when performing these driving patterns.




- (a) Connect the intelligent tester to the DLC3.
- (b) Turn the ignition switch to ON.
- (c) Turn the tester ON.
- (d) Clear DTCs (Click here).
- (e) Start the engine, and warm it up until the ECT reaches 75°C (167°F) or higher.
- (f) Enter the following menus: Powertrain / Engine and ECT / Data List / Idle Fuel Cut.
- (g) Drive the vehicle at between 60 km/h (38 mph) and 120 km/h (75 mph) for at least 10 minutes.
- (h) Change the transmission to 2nd gear.
- (i) Drive the vehicle at proper vehicle speed to perform fuel cut operation (refer to the following HINT).
- HINT:
- fuel cut is performed when the following conditions are met:
- Accelerator pedal fully released.
- Engine speed is 2500 rpm or more (fuel injection returns at 1000 rpm).
- Accelerator pedal fully released.
- (j) Accelerate the vehicle to 64 km/h (40 mph) or more by depressing the accelerator pedal for at least 10 seconds.
- (k) Soon after performing step (j) above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal, in order to execute fuel cut control.
- (l) Allow the vehicle to decelerate until the vehicle speed declines to less than 10 km/h (6 mph).
- (m) Repeat steps from (h) through (k) above at least 3 times in one driving cycle.
- HINT:
- Completion of all A/F sensor monitors is required to change the value in Test Result.
INSPECTION PROCEDURE
- HINT:
- Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
- The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.
- (1) Connect the intelligent tester to the DLC3.
- (2) Start the engine and turn the tester ON.
- (3) Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
- (4) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
- (5) Perform the Control the Injection Volume for A/F sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
- (6) Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.
- (1) Connect the intelligent tester to the DLC3.
- HINT:
- The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
- Standard:
Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS B1S1 or AFS B2S1
(A/F)
+25%
Rich
Less than 3.0 V
AFS B1S1 or AFS B2S1
(A/F)
-12.5%
Lean
More than 3.35 V
O2S B1S2 or O2S B2S2
(HO2)
+25%
Rich
More than 0.55 V
O2S B1S2 or O2S B2S2
(HO2)
-12.5%
Lean
Less than 0.4 V
- The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- NOTICE:
- The Air Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.
| Case |
A/F Sensor (Sensor 1) Output Voltage |
HO2 Sensor (Sensor 2) Output Voltage |
Main Suspected Trouble Area |
| 1 |
![]() ![]() ![]() ![]() |
![]() ![]() ![]() ![]() |
- |
| 2 |
![]() ![]() ![]() ![]() |
![]() ![]() ![]() ![]() |
|
| 3 |
![]() ![]() ![]() ![]() |
![]() ![]() ![]() ![]() |
|
| 4 |
![]() ![]() ![]() ![]() |
![]() ![]() ![]() ![]() |
|
- Following the Control the Injection Volume for A/F sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
- To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor / A/F Control System / AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2, then press View button.
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
- A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
- Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, P2197 OR P2198) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
Result Result
Proceed to
P2195, P2196, P2197 or P2198
A
P2195, P2196, P2197 or P2198 and other DTCs
B
- HINT:
- If any DTCs other than P2195, P2196, P2197 or P2198 are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (TEST VALUE OF A/F SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Clear DTCs (Click here).
Allow the vehicle to drive in accordance with the drive pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / Monitor Status / O2 Sensor.
Check that the status of O2 Sensor is Complete.If the status is still Incomplete, drive the vehicle according to the driving pattern again.
Enter the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor / Details / Range B1S1.
Check the test value of the A/F sensor output current during fuel cut.
Result Result
Proceed to
Within normal range (1.4 mA or more, and less than 3.6 mA)
A
Outside normal range (Less than 1.4 mA, or 3.6 mA or more)
B
|
|
||||
| A | |
| 3. READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF A/F SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester ON.
Warm up the Air Fuel Ratio (A/F) sensor at an engine speed of 2500 rpm for 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / AFS B1S1 and Engine Speed, then press the Record button.
Check the A/F sensor voltage three times, when the engine is in each of the following conditions:
While idling (check for at least 30 seconds)
At an engine speed of approximately 2500 rpm (without any sudden changes in engine speed)
Raise the engine speed to 4000 rpm and then quickly release the accelerator pedal so that the throttle valve is fully closed.
- Standard Voltage:
Condition
A/F Sensor Voltage Variation
Reference
(1) and (2)
Changes at approximately 3.3 V
Between 3.1 V and 3.5 V
(3)
Increases to 3.8 V or more
This occurs during engine deceleration
(when fuel cut performed)
- HINT:
- For more information, see the diagrams below.


- HINT:
- If the output voltage of the A/F sensor remains at approximately 3.3 V (see Malfunction Condition diagram) under any conditions, including those above, the A/F sensor may have an open circuit. (This will also happen if the A/F sensor heater has an open circuit.)
- If the output voltage of the A/F sensor remains at either approximately 3.8 V or more, or 2.8 V or less (see Malfunction Condition diagram) under any conditions, including those above, the A/F sensor may have a short circuit.
- The ECM stops fuel injection (fuel cut) during engine deceleration. This causes a lean condition and results in a momentary increase in the A/F sensor output voltage.
- The ECM must establish a closed throttle valve position learning value to perform fuel cut. If the battery terminal has been reconnected, the vehicle must be driven over 16 km/h (10 mph) to allow the ECM to learn the closed throttle valve position.
- When the vehicle is driven:
The output voltage of the A/F sensor may be below 2.8 V during fuel enrichment. For the vehicle, this translates to a sudden increase in speed with the accelerator pedal fully depressed when trying to overtake another vehicle. The A/F sensor is functioning normally.
- The A/F sensor is a current output element; therefore, the current is converted into a voltage inside the ECM. Measuring the voltage at the connectors of the A/F sensor or ECM will show a constant voltage result.
- If the output voltage of the A/F sensor remains at approximately 3.3 V (see Malfunction Condition diagram) under any conditions, including those above, the A/F sensor may have an open circuit. (This will also happen if the A/F sensor heater has an open circuit.)
|
|
||||
| OK | |
| 4. PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 5. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read DTCs.
Result Result
Proceed to
P2195, P2196, P2197 or P2198
A
No output
B
|
|
||||
| A | |
| 6. REPLACE AIR FUEL RATIO SENSOR |
| NEXT | |
| 7. PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 8. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read DTCs.
Result Result
Proceed to
No output
A
P2195, P2196, P2197 or P2198
B
|
|
||||
| A | |
| 9. CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
| Result |
Proceed to |
| Vehicle has run out of fuel |
A |
| Vehicle has not run out of fuel |
B |
|
|
||||
| A | ||
| ||
| 10. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() ![]() |
Disconnect the B33*1 or B31*2 A/F sensor connector.
- HINT:
- *1: Bank 1 Sensor 1
- *2: Bank 2 Sensor 1
- *1: Bank 1 Sensor 1
Measure the resistance between the terminals of the A/F sensor connector.
- Standard Resistance (Bank 1 Sensor 1):
Tester Connections
Specified Conditions
HA1A (1) - +B (2)
1.8 to 3.4 Ω at 20°C (68°F)
HA1A (1) - A1A- (4)
10 kΩ or higher
- Standard Resistance (Bank 2 Sensor 1):
Tester Connections
Specified Conditions
HA2A (1) - +B (2)
1.8 to 3.4 Ω at 20°C (68°F)
HA2A (1) - A2A- (4)
10 kΩ or higher
Reconnect the A/F sensor connector.
|
|
||||
| OK | |
| 11. INSPECT AIR FUEL RATIO SENSOR HEATER RELAY |
![]() ![]() |
Remove the A/F sensor heater relay from the engine room relay block.
Check the A/F sensor heater relay resistance.
- Standard Resistance:
Tester Connections
Specified Conditions
3 - 5
10 kΩ or higher
Below 1 Ω
(when battery voltage applied to terminals 1 and 2)
Reinstall the A/F sensor heater relay.
|
|
||||
| OK | |
| 12. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() ![]() |
Disconnect the A/F sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B33-2 (+B) - Body ground
Ignition switch ON
11 to 14 V
B31-2 (+B) - Body ground
Ignition switch ON
11 to 14 V
Turn the ignition switch off.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B33-1 (HA1A) - B2-2 (HA1A)
Always
Below 1 Ω
B33-3 (A1A+) - B2-22 (A1A+)
Always
Below 1 Ω
B33-4 (A1A-) - B2-30 (A1A-)
Always
Below 1 Ω
B31-1 (HA2A) - B2-1 (HA2A)
Always
Below 1 Ω
B31-3 (A2A+) - B2-23 (A2A+)
Always
Below 1 Ω
B31-4 (A2A-) - B2-31 (A2A-)
Always
Below 1 Ω
B33-1 (HA1A) or B2-2 (HA1A) - Body ground
Always
10 kΩ or higher
B33-3 (A1A+) or B2-22 (A1A+) - Body ground
Always
10 kΩ or higher
B33-4 (A1A-) or B2-30 (A1A-) - Body ground
Always
10 kΩ or higher
B31-1 (HA2A) or B2-1 (HA2A) - Body ground
Always
10 kΩ or higher
B31-3 (A2A+) or B2-23 (A2A+) - Body ground
Always
10 kΩ or higher
B31-4 (A2A-) or B2-31 (A2A-) - Body ground
Always
10 kΩ or higher
Reconnect the ECM connector.
Reconnect the A/F sensor connector.


|
|
||||
| OK | |
| 13. CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leak.
- OK:
- No leak from air induction system.
|
|
||||
| OK | |
| 14. CHECK FUEL PRESSURE |
Check the fuel pressure (Click here).
|
|
||||
| OK | |
| 15. INSPECT FUEL INJECTOR ASSEMBLY |
Check the fuel injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
|
||||
| OK | |
| 16. REPLACE AIR FUEL RATIO SENSOR |
| NEXT | |
| 17. PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 18. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read DTCs.
Result Result
Proceed to
No output
A
P2195, P2196, P2197 or P2198
B
|
|
||||
| A | |
| 19. CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
| Result |
Proceed to |
| Vehicle has run out of fuel |
A |
| Vehicle has not run out of fuel |
B |
|
|
||||
| A | ||
| ||
| 20. REPLACE AIR FUEL RATIO SENSOR |
| NEXT | |
| 21. PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 22. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read DTCs.
Result Result
Proceed to
No output
A
P2195, P2196, P2197 or P2198 (A/F sensor pending DTCs)
B
|
|
||||
| A | ||
| ||







