2011-2016 FJ Cruiser · Service Manual BRAKE

C1425 Open in Stop Light Switch Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Nov 2010 – Jul 2012 Aug 2012 – Jul 2014 from Aug 2014

DESCRIPTION

The master cylinder solenoid (skid control ECU) inputs stop light switch signals and the brake operation condition.
The skid control ECU has an open detection circuit, which outputs this DTC when detecting an open circuit in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).
DTC Code
DTC Detection Condition
Trouble Area
C1425
When the IG1 terminal voltage is between 9.5 and 17.4 V and the skid control ECU STPO terminal output is off, an open in the stop light switch circuit continues for 3 seconds or more.
  1. STOP fuse
  2. Stop light switch
  3. Stop light switch circuit
  4. Master cylinder solenoid (skid control ECU)

WIRING DIAGRAM

Refer to DTC C1380 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. When replacing the master cylinder solenoid, perform calibration (Click here).


1. CHECK STOP LIGHT SWITCH OPERATION
  1. Check that the stop light comes on when the brake pedal is depressed and turns off when the brake pedal is released.

    OK:
    Stop light switch function is normal.



NG
GO TO LIGHTING SYSTEM (PROBLEM SYMPTOMS TABLE) (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch display observed on the tester changes according to brake pedal operation.

    OK:
    The tester displays ON or OFF according to brake pedal operation.

    HINT:
    While checking the Data List, if the display changes when the wire harness or connector is jiggled, vibrated, etc., there may be a connection problem with the connector or an intermittent open circuit.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. INSPECT SKID CONTROL ECU (STP TERMINAL)
  1. Disconnect the skid control ECU connector.

  1. C213546E18
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A4-7 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    A4-7 (STP) - Body ground
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← C1425 Open in Stop Light Switch Circuit (Aug 2012 – Jul 2014)C1432 Steering Angle Sensor Power Source Voltage Malfunction (Nov 2010 – Jul 2011) →