2011-2016 FJ Cruiser · Service Manual ENGINE

Fuel Injector Circuit

Circuit diagnosis · Vehicles built Jul 2007 – Nov 2007

Versions by build date: Jul 2007 – Nov 2007 Dec 2007 – Jul 2009 Aug 2009 – Oct 2010 from Nov 2010

DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

A171629E02

INSPECTION PROCEDURE


1. INSPECT FUEL INJECTOR (POWER SOURCE)

  1. A167963E04
    Disconnect the fuel injector connectors.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connections
    Specified Conditions
    B11-2 - Body ground
    11 to 14 V
    B25-2 - Body ground
    11 to 14 V
    B10-2 - Body ground
    11 to 14 V
    B21-2 - Body ground
    11 to 14 V
    B9-2 - Body ground
    11 to 14 V
    B18-2 - Body ground
    11 to 14 V

  1. Reconnect the fuel injector connectors.



NG
Go to step 6
OK


2. INSPECT FUEL INJECTOR (INJECTOR RESISTANCE)
A141550E08
  1. Disconnect the fuel injector connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connections
    Specified Conditions
    1 - 2
    11.6 to 12.4 Ω
    20°C (68°F)

  1. Reconnect the fuel injector connectors.



NG
REPLACE FUEL INJECTOR (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)

  1. A173386E01
    Disconnect the B3 ECM connector.

  1. Disconnect the B9, B10, B11, B18, B21 and B25 fuel injector connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    B9-1 - B3-2 (#10)
    Below 1 Ω
    B10-1 - B3-3 (#20)
    Below 1 Ω
    B11-1 - B3-4 (#30)
    Below 1 Ω
    B18-1 - B3-5 (#40)
    Below 1 Ω
    B21-1 - B3-6 (#50)
    Below 1 Ω
    B25-1 - B3-7 (#60)
    Below 1 Ω

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    B9-1 or B3-2 (#10) - Body ground
    10 kΩ or higher
    B10-1 or B3-3 (#20) - Body ground
    10 kΩ or higher
    B11-1 or B3-4 (#30) - Body ground
    10 kΩ or higher
    B18-1 or B3-5 (#40) - Body ground
    10 kΩ or higher
    B21-1 or B3-6 (#50) - Body ground
    10 kΩ or higher
    B25-1 or B3-7 (#60) - Body ground
    10 kΩ or higher

  1. Reconnect the fuel injector connectors.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
A171627E02
  1. Disconnect the B1 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    B1-7 (E01) - Body ground
    Below 1 Ω
    B1-6 (E02) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT FUEL INJECTOR (INJECTION AND VOLUME)
  1. Check the fuel injector and volume (Click here).



NG
REPLACE FUEL INJECTOR (Click here)
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

6. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - IGNITION SWITCH)
A173387E01
  1. Disconnect the B9, B10, B11, B18, B21 and B25 fuel injector connectors.

  1. Disconnect the A1 ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for short):
    Tester Connections
    Specified Conditions
    B9-2 - A1-6 (IG2)
    Below 1 Ω
    B10-2 - A1-6 (IG2)
    Below 1 Ω
    B11-2 - A1-6 (IG2)
    Below 1 Ω
    B18-2 - A1-6 (IG2)
    Below 1 Ω
    B21-2 - A1-6 (IG2)
    Below 1 Ω
    B25-2 - A1-6 (IG2)
    Below 1 Ω

    Standard Resistance (Check for open):
    Tester Connections
    Specified Conditions
    B9-2 or A1-6 (IG2) - Body ground
    10 kΩ or higher
    B10-2 or A1-6 (IG2) - Body ground
    10 kΩ or higher
    B11-2 or A1-6 (IG2) - Body ground
    10 kΩ or higher
    B18-2 or A1-6 (IG2) - Body ground
    10 kΩ or higher
    B21-2 or A1-6 (IG2) - Body ground
    10 kΩ or higher
    B25-2 or A1-6 (IG2) - Body ground
    10 kΩ or higher

  1. Reconnect the fuel injector connectors.

  1. Reconnect the ignition switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE ECM POWER SOURCE CIRCUIT (Click here)


← Fuel Pump Control Circuit (from Aug 2014)Fuel Injector Circuit (Dec 2007 – Jul 2009) →