2011-2016 FJ Cruiser · Service Manual ENGINE

P2431 Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

DESCRIPTION

Refer to DTC P0412 (Click here).
Refer to DTC P0416 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P2431
P2436
Pressure sensor indicates a value below 45.63 kPa (342 mmHg), or higher than 135 kPa (1013 mmHg) (2 trip detection logic).
  1. Pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (bank 2))
  2. Open or short in pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (bank 2)) circuit
  3. ECM
P2432
P2437
While the engine is running, the voltage output of the pressure sensor is below 0.5 V (1 trip detection logic).
  1. Pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (bank 2))
  2. Open or short in pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (bank 2)) circuit
  3. ECM
P2433
P2438
While the engine is running, the voltage output of the pressure sensor is higher than 4.5 V (1 trip detection logic).
  1. Pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (bank 2))
  2. Open or short in pressure sensor (Emission control valve set (for bank 1) and No. 2 emission control valve set (bank 2)) circuit
  3. ECM

MONITOR DESCRIPTION

A085160E22
The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the emission control valve set in the secondary air injection system. Using this pressure value, the ECM determines whether the secondary air injection system is malfunctioning or not.
If there is a defect in the sensor or the sensor circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the pressure sensor or circuit and stores a DTC.

CONFIRMATION DRIVING PATTERN

NOTICE:
  1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.
  2. Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
  3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
  4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  1. Start the engine and warm it up.
  2. Turn the ignition switch off.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the tester on.
  6. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the tester on.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
  10. Start the engine after the tester initialization is finished.
  11. Perform the System Check operation by pressing Next.
  12. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
  13. Enter the following menus: Powertrain / Engine and ECT / DTC.
  14. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  15. After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  16. Input the DTC: P2431, P2432, P2433, P2436, P2437 or P2438.
  17. Check the DTC judgment result.
    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.


WIRING DIAGRAM

A329623E01

INSPECTION PROCEDURE

HINT:
  1. Refer to "Data List / Active Test" [Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute)] (Click here).
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.


1. CHECK HARNESS AND CONNECTOR (EMISSION CONTROL VALVE SET - ECM)
  1. Disconnect the B67 and B68 emission control valve set connectors.

  1. Disconnect the B47, B48 and E82 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B67-3 (AIP) - E82-1 (AIP)
    Always
    Below 1 Ω
    B67-2 (VC) - B47-16 (VCV2)
    Always
    Below 1 Ω
    B67-4 (E2) - B48-7 (ETHA)
    Always
    Below 1 Ω
    B68-3 (AIP2) - E82-2 (AIP2)
    Always
    Below 1 Ω
    B68-2 (VC2) - B47-16 (VCV2)
    Always
    Below 1 Ω
    B68-4 (E22) - B48-7 (ETHA)
    Always
    Below 1 Ω
    B67-3 (AIP) or E82-1 (AIP) - Body ground
    Always
    10 kΩ or higher
    B67-2 (VC) or B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher
    B68-3 (AIP2) or E82-2 (AIP2) - Body ground
    Always
    10 kΩ or higher
    B68-2 (VC2) or B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK TERMINAL VOLTAGE (VC OF EMISSION CONTROL VALVE SET)
A219201E11
  1. Disconnect the emission control valve set connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B67-2 (VC) - B67-4 (E2)
    Ignition switch ON
    4.5 to 5.5 V
    B68-2 (VC2) - B68-4 (E22)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Emission Control Valve Set)
    *b
    for Bank 1
    *c
    for Bank 2



NG
REPLACE ECM (Click here)
OK


3. REPLACE EMISSION CONTROL VALVE SET
  1. Replace the emission control valve set.

    HINT:
    1. Replace the emission control valve set (Click here).
    2. Replace the No. 2 emission control valve set (Click here).


NEXT


4. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for 30 seconds.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2431, P2432, P2433, P2436, P2437 or P2438.

  1. Check the DTC judgment result.

    Result 
    Result
    Proceed to
    NORMAL
    (No DTC is output)
    A
    ABNORMAL
    (P2431, P2432, P2433, P2436, P2437 or P2438 is output)
    B



B
REPLACE ECM (Click here)
A

END


← P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) (+ 9 more codes) (from Aug 2014)P2440 Secondary Air Injection System Switching Valve Stuck Open Bank1 (+ P2441, P2442, P2443) (from Aug 2014) →