2011-2016 FJ Cruiser · Service Manual ENGINE

P0365 Camshaft Position Sensor "B" Circuit (Bank 1)

Diagnostic trouble codes · Vehicles built from Aug 2009

Also covers:

DESCRIPTION

The camshaft position sensor for the exhaust camshaft (EV signal sensor) consists of a magnet and an MRE element.
The exhaust camshaft has a timing rotor for the VVT sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE element, which affect the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the camshaft rotation data to pulse signals, and uses the pulse signals to determine the camshaft angle, which it sends to the ECM. Then the ECM uses this data to control fuel injection duration, injection timing and the Variable Valve Timing (VVT) system.
DTC No.
DTC Detection Condition
Trouble Area
P0365
P0390
Missing exhaust VVT sensor signal for 5 seconds at engine speed of 600 rpm or more(1 trip detection logic)
  1. Open or short in VVT sensor circuit (for exhaust side)
  2. VVT sensor (for exhaust side)
  3. Camshaft sub-assembly (for exhaust side)
  4. ECM
P0367
P0392
Output voltage of VVT sensor less than 0.3 V for 4 seconds (1 trip detection logic)
P0368
P0393
Output voltage of VVT sensor more than 4.7 V for 4 seconds (1 trip detection logic)

  1. A122768E04
  2. Inspection using an oscilloscope

    HINT:
    1. The correct waveform is shown above.
    2. EV1+ and EV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.


MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

WIRING DIAGRAM

Refer to DTC P0335 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


1. INSPECT ECM TERMINAL VOLTAGE
A226983E01
  1. Inspect the ECM using an oscilloscope.

    1. While the engine is idling, check the waveform between the terminals of the ECM connector.

      Standard:
      Tester Connection
      Tool Setting
      Condition
      Specified Condition
      B47-13 (EV1+) - B47-14 (EV1-)
      5 V/DIV., 20 msec./DIV.
      Idling
      Correct waveform as shown in illustration
      B47-18 (EV2+) - B47-17 (EV2-)
      5 V/DIV., 20 msec./DIV.
      Idling
      Correct waveform as shown in illustration
      B47-6 (NE+) - B47-5 (NE-)
      5 V/DIV., 20 msec./DIV.
      Idling
      Correct waveform as shown in illustration

      Text in Illustration 
      *1
      Rear view of wire harness connector
      (to ECM)
      *2
      EV1, EV2 and NE Signal Waveforms



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. CHECK VVT SENSOR (SENSOR POWER SOURCE)
A193258E03
  1. Disconnect the VVT sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B57-3 (VC2) - Body ground
    Ignition switch ON
    4.5 to 5.5 V
    B58-3 (VC2) - Body ground
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to VVT Sensor)
    *2
    for bank 1
    *3
    for bank 2



NG
Go to step 8
OK


3. CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
  1. Disconnect the VVT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B57-1 (EX+) - B47-13 (EV1+)
    Always
    Below 1 Ω
    B58-1 (EX+) - B47-18 (EV2+)
    Always
    Below 1 Ω
    B57-2 (EX-) - B47-14 (EV1-)
    Always
    Below 1 Ω
    B58-2 (EX-) - B47-17 (EV2-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B57-1 (EX+) or B47-13 (EV1+) - Body ground
    Always
    10 kΩ or higher
    B58-1 (EX+) or B47-18 (EV2+) - Body ground
    Always
    10 kΩ or higher
    B57-2 (EX-) or B47-14 (EV1-) - Body ground
    Always
    10 kΩ or higher
    B58-2 (EX-) or B47-17 (EV2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK SENSOR INSTALLATION (VVT SENSOR)
BR03795E32
  1. Check the VVT sensor installation.

    OK:
    Sensor is installed correctly.



NG
TIGHTEN SENSOR (Click here)
OK


5. INSPECT CAMSHAFT ASSEMBLY (TIMING ROTOR)
  1. Check the timing rotor of the exhaust camshaft.

    OK:
    Camshaft timing rotor does not have any cracks or deformation.



NG
REPLACE CAMSHAFT (FOR EXHAUST SIDE) (Click here)
OK


6. REPLACE VVT SENSOR (FOR EXHAUST SIDE)
  1. Replace the VVT sensor (for exhaust side) (Click here).


OK


7. CHECK WHETHER DTC OUTPUT RECURS (P0365,P0367,P0368,P0390,P0392 or P0393)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Switch the ECM from normal mode to check mode (Click here).

  1. Start the engine again and allow the engine to idle for 10 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0365,P0367,P0368,P0390,P0392 or P0393 is output
    A
    DTC is not output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
END
A

REPLACE ECM (Click here)

8. CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
  1. Disconnect the VVT sensor (for exhaust side) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B57-3 (VC2) - B47-15 (VCV1)
    Always
    Below 1 Ω
    B58-3 (VC2) - B47-16 (VCV2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B57-3 (VC2) or B47-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    B58-3 (VC2) or B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0351 Ignition Coil "A" Primary / Secondary Circuit (+ 5 more codes) (from Aug 2014)P0412 Secondary Air Injection System Switching Valve "A" Circuit (from Aug 2014) →