2011-2016 FJ Cruiser · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Nov 2012 – Jul 2013

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Oct 2012 Nov 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL ENGINE WIRE
  1. Connect the connectors to the engine.

  1. Engage the clamps to the engine.

  1. Install the ground wire onto the bank 1 camshaft housing with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the ground wire onto the bank 1 cylinder head cover with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


2. INSTALL ENGINE HANGER
  1. Install the 2 engine hangers with the 4 bolts.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }


3. INSTALL ENGINE ASSEMBLY
  1. Attach the engine sling device and hang the engine with a chain block.

  1. Lower the engine into the engine compartment carefully.

  1. A245609E01
    Install the 2 front engine mounting insulators with the 6 nuts and 4 bolts.
    Text in Illustration 
    *1
    Mounting Bracket RH
    *a
    Front View of Mounting Bracket RH
    *b
    Top of Vehicle
    *c
    Front of Vehicle
    *d
    Claw
    *e
    Edge of Mounting Bracket RH
    *f
    Clip Installation Range

    Torque:
    for nut A:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }
    for nut B:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    NOTICE:
    For the rear bolt on the RH side only, make sure to install it so that the claw does not protrude past the edge of the mounting bracket.

  1. Remove the 4 bolts and 2 engine hangers.

  1. Install the fuel pipe clamp with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install the wire harness clamp with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


4. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. Temporarily install the flywheel with the 8 new bolts.

  1. Install and tighten the 8 mounting bolts uniformly in several steps.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Mark the top of the bolts with paint.

  1. Tighten the 8 bolts 90° in the same sequence.

  1. Check that the paint marks are now at a 90° angle to the top.


5. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A227952E01
    Install the front drive plate spacer, drive plate and ring gear and rear drive plate spacer onto the crankshaft.
    Text in Illustration 
    *1
    Front Drive Plate Spacer
    *2
    Drive Plate and Ring Gear
    *3
    Rear Drive Plate Spacer
    V100135
    Transmission Side

    HINT:
    As the front drive plate spacer, drive plate and ring gear and rear drive plate spacer are not reversible, be sure to install it in the direction shown in the illustration.

  1. A057108
    Apply adhesive to the 2 or 3 end threads of the bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

  1. A224777E01
    Uniformly install and tighten the 8 bolts in several steps in the sequence shown in the illustration.

    Torque:
    83 N*m{ 846 kgf*cm , 61 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 1 hour after installing.


6. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

C135774
  1. Insert SST into the clutch disc assembly, then insert them into the flywheel sub-assembly.

    SST
    09301-00220  

    NOTICE:
    Insert the clutch disc assembly in the correct orientation.


7. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

C135776E02
  1. Align the matchmarks on the clutch cover assembly and flywheel sub-assembly.

    Text in Illustration 
    *a
    Temporarily
    *b
    Matchmark

  1. Following the procedures shown in the illustration, tighten the 6 bolts, in the order starting with the bolt located near the knock pin on the top.

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

    HINT:
    1. Following the order in the illustration, uniformly tighten the bolts.
    2. Move SST up and down, right and left lightly, after checking that the disc is in the center, and tighten the bolts.


8. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)

C135777
  1. Using a dial indicator with roller instrument, check the diaphragm spring tip alignment.

    Maximum non-alignment:
    0.5 mm (0.020 in.)

    If the alignment is not as specified, adjust the diaphragm spring tip alignment using SST.
    SST
    09333-00013  


9. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
(Click here)

10. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)

11. CONNECT ENGINE WIRE (for Automatic Transmission)
  1. Install the wire harness clamp bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the front differential connector and clamp.


12. CONNECT ENGINE WIRE

A226129E01
  1. Engage the grommet to the wire harness support.

    Text in Illustration 
    *1
    Grommet
    *2
    Wire Harness Support

  1. Pass the wire harness into the vehicle and install the wire harness support.

  1. Install the ground wire with the bolt and connect the connector.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Connect the 3 connectors and clamp to the air conditioning unit.

  1. Connect the 6 connectors to the ECM.

  1. Connect the connector to the four wheel drive control ECU.

  1. Install the glove compartment door (Click here).


13. CONNECT OUTLET HEATER WATER HOSE

A225912E01
  1. Connect the outlet heater water hose.

    Text in Illustration 
    *a
    View A
    *b
    Top of Vehicle
    *c
    LH of Vehicle

    HINT:
    The direction of the hose clamp is indicated in the illustration.


14. CONNECT INLET HEATER WATER HOSE

A225911E01
  1. Connect the inlet heater water hose.

    Text in Illustration 
    *a
    View A
    *b
    Top of Vehicle
    *c
    LH of Vehicle

    HINT:
    The direction of the hose clamp is indicated in the illustration.


15. CONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY
  1. Connect the No. 2 fuel pipe (Click here).

  1. Install the No. 2 fuel pipe clamp.


16. CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY
  1. Connect the No. 1 fuel pipe (Click here).

  1. Connect the fuel pipe clamp.


17. INSTALL VANE PUMP ASSEMBLY
  1. Install the vane pump with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Connect the 2 clamps and vane pump connector.


18. INSTALL COOLER COMPRESSOR ASSEMBLY

A225903E01
  1. Temporarily install the cooler compressor with the 3 bolts.

  1. Using a E8 "TORX" socket wrench, install the stud bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the nut.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. Fully tighten the 3 bolts in the order shown in the illustration.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. Install the suction hose with the bolt.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }


19. INSTALL STARTER ASSEMBLY
(Click here)

20. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY
(Click here)

21. INSTALL GENERATOR ASSEMBLY
(Click here)

22. INSTALL INTAKE AIR SURGE TANK
  1. Install a new gasket to the intake air surge tank.

  1. Install the intake air surge tank in the order shown in the illustration.

    1. A227191E01
      Using a 8 mm socket hexagon wrench, temporarily tighten the 4 bolts to the intake air surge tank.

    2. Temporarily tighten the 2 nuts to the intake air surge tank.

      Text in Illustration 
      V100136
      Nut

    3. Tighten the 4 bolts and 2 nuts.

      Torque:
      28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. A226752E01
    Install the No. 2 surge tank stay with the 2 bolts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A226751E01
    Install the No. 1 surge tank stay with the 2 bolts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Engage the wire harness clamp.

  1. A221460E01
    Install the throttle body bracket with the 2 bolts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A226866E01
    Connect the No. 1 ventilation hose.
    Text in Illustration 
    *a
    Front

  1. A226867E01
    Connect the No. 1 vacuum switching valve connector.
    Text in Illustration 
    *a
    Front
    *b
    Matchmark
    *c
    Top

  1. Connect the No. 1 fuel feed hose.

    HINT:
    Connect the hose so that the direction of the hose clamp is as indicated in the illustration.

  1. Connect the throttle body connector.

  1. A226865E01
    Connect the No. 4 water by-pass hose.
    Text in Illustration 
    *a
    RH
    *b
    Rear
    *c
    Top
    *d
    Matchmark

    HINT:
    Connect the hose so that the direction of the hose clamp is as indicated in the illustration.

  1. Connect the No. 5 water by-pass hose.

    HINT:
    Connect the hose so that the direction of the hose clamp is as indicated in the illustration.

  1. Connect the 2 heater hose clamps.


23. INSTALL AIR CLEANER CASE SUB-ASSEMBLY
  1. Install the air cleaner case sub-assembly with the 3 bolts.


24. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.


25. INSTALL AIR CLEANER CAP AND HOSE

  1. A227195E01
    Install the air cleaner cap with the 4 hinges.

  1. Install the No. 1 air cleaner hose with the clamp.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    Text in Illustration 
    *a
    Protrusion
    *b
    Groove
    *c
    Top
    *d
    Front
    *e
    RH
    *f
    Paint mark of the hose

  1. Install the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the ventilation hose and vacuum hose.

    HINT:
    The direction of the hose clamp is indicated in the illustration.

  1. Engage the 4 wire harness clamps.

  1. Connect the MAF meter connector.


26. INSTALL RADIATOR ASSEMBLY
  1. Remove the radiator assembly (Click here).


27. INSTALL HOOD SUB-ASSEMBLY
  1. Install the hood with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the windshield washer hose.


28. INSTALL HOOD SUPPORT

B135982
  1. Install the 2 stop rings onto the hood support.

  1. Install the hood support.


29. ADJUST HOOD SUB-ASSEMBLY

B135977
  1. Adjust the hood position.

    1. Loosen the 4 hinge bolts on the hood side.

    2. Move the hood and adjust the clearance between the hood and front fender. Make sure that the clearance is within the standard range.

      Standard(A):
      4.0 to 7.0 mm (0.157 to 0.276 in.)

    3. Tighten the hood side hinge bolts after the adjustment.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. B135976
    Adjust the cushion rubber so that the heights of the hood and the fender are equal.

    1. Raise or lower the hood front end by turning the cushion rubber. Make sure that the clearance is within the standard range.

      HINT:
      Raise or lower the cushion rubber by turning it.

  1. B135978
    Adjust the hood lock.

    1. Disengage the 4 claws and remove the hood lock release lever protector.

    2. B135979
      Loosen the 3 bolts.

    3. B135980
      Adjust the hood lock position so that the striker can enter it smoothly.

    4. B135979
      Tighten the 3 bolts after the adjustment.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    5. B135978
      Engage the 4 claws and install the hood lock release lever protector.


30. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


31. ADD ENGINE COOLANT
  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.

  1. Add engine coolant.

    Standard Capacity:
    Item
    Specified Condition
    for Automatic Transmission
    9.8 liters (10.4 US qts, 8.6 Imp. qts)
    for Manual Transmission
    9.4 liters (9.9 US qts, 8.3 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. A220212E02
    Slowly pour coolant into the radiator reservoir until it reaches the Full line.
    Text in Illustration 
    *1
    FULL Line

  1. Install the reservoir cap.

  1. Install the radiator cap.*1

  1. Start the engine and stop it immediately.*2

  1. Allow approximately 10 seconds to pass, and then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3

  1. Repeat steps *1, *2 and *3 until the coolant level does not decrease.

    HINT:
    Be sure to perform this step while the engine is cold, as air in the No. 1 radiator hose will flow into the radiator if the engine is warmed up and the thermostat opens.

  1. Install the radiator cap.*4

  1. Set the air conditioning as follows.*5

    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6

    CAUTION:
    1. Wear protective gloves. Hot areas on the parts may injure your hands.
    2. Be careful of the fan.
    3. Be careful as the engine, radiator and radiator hoses are hot and can cause burns.

    NOTICE:
    1. Immediately after starting the engine, if the radiator reservoir becomes empty, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the Full line.
    2. Do not start the engine when there is no coolant in the radiator reservoir.
    3. Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
    4. If there is not enough coolant, the engine may burn out or overheat.

    HINT:
    1. Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air while warming up the engine.
    2. The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, wait until the engine coolant cools down to ambient temperature, and then remove the radiator cap and check the coolant level.*7

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8

  1. A220212E02
    If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the Full line.
    If the coolant level is below the Full line, repeat steps *4 through *8.
    If the coolant level is above the Full line, drain coolant until the coolant level reaches the Full line.
    Text in Illustration 
    *1
    FULL Line


32. ADD ENGINE OIL

  1. Add fresh oil.

    NOTICE:
    A308107
    Do not allow engine oil to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.
    If engine oil is on the location indicated by the arrow, replace the belt tensioner.


    Standard Engine Oil:
    Oil grade
    Oil Viscosity (SAE)
    API grade SL "Energy- Conserving", SM "Energy- Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil
    0W-20 (*1)
    5W-20 (*1)
    5W-30 (*2)
    10W-30 (*2)
    API grade SL, SM or SN multigrade engine oil
    15W-40 (*2)
    20W-50 (*2)

    (*1): for China (*2):for All

    Standard Oil Capacity (w/o Oil Cooler):
    Item
    Specified Condition
    Drain and refill without oil filter change
    5.7 liters (6.0 US qts, 5.0 Imp. qts)
    Drain and refill with oil filter change
    6.1 liters (6.4 US qts, 5.4 Imp. qts)
    Dry fill
    6.9 liters (7.3 US qts, 6.1 Imp. qts)


    Standard Oil Capacity (w/ Oil Cooler):
    Item
    Specified Condition
    Drain and refill without oil filter change
    5.7 liters (6.0 US qts, 5.0 Imp. qts)
    Drain and refill with oil filter change
    6.2 liters (6.6 US qts, 5.5 Imp. qts)
    Dry fill
    7.1 liters (7.5 US qts, 6.3 Imp. qts)


33. PERFORM INITIALIZATION (for Automatic Transmission)
(Click here)

34. INSPECT FOR COOLANT LEAK

CAUTION:
To avoid being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion may cause hot engine coolant and steam to blow out from the radiator.

  1. Fill the radiator with engine coolant, and then attach a radiator cap tester.

  1. Warm up the engine.

  1. A220211E01
    Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
    Text in Illustration 
    *1
    Radiator Cap Tester


35. INSPECT FOR ENGINE OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.


36. INSPECT FOR FUEL LEAK
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

    NOTICE:
    Do not start the engine.

  1. Turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Speed / ON.

  1. Check fuel pump operation.

    1. Check for pressure in the fuel inlet tube from the fuel line. Check that the sound of fuel flowing in the fuel tank can be heard.
      If there is no sound, check the integration relay, fuel pump, ECM and wiring connector.


37. INSPECT FOR EXHAUST GAS LEAK

38. INSTALL REAR ENGINE UNDER COVER ASSEMBLY
  1. Install the rear engine under cover with the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


39. INSTALL TRANSMISSION UNDER COVER (w/ Transmission Under Cover)
  1. Install the transmission under cover with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


40. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Hook the engine under cover to the frame.

  1. Install the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


41. CHECK ENGINE OIL LEVEL
  1. Warm up the engine, then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.


42. INSPECT IGNITION TIMING

NOTICE:
  1. Turn all electrical systems off.
  1. Perform the inspection when the cooling fan motor is turned off.

  1. Warm up the engine.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / IGN Advance.

    3. Inspect the ignition timing during idling.

      Standard ignition timing:
      8 to 12° BTDC idling (transmission in neutral and A/C switch off)

    4. Check that the ignition timing advances immediately when the engine speed is increased.

  1. A206183E05
    When not using the intelligent tester:
    Text in Illustration 
    *a
    Front view of DLC3:

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      Be sure not to improperly connect the terminals. This may damage the engine.

    2. A225898
      Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

      NOTICE:
      1. Use a timing light that detects primary signals.
      1. After the inspection, be sure to wrap the wire harness with tape.

    3. A076316E01
      Inspect the ignition timing during idling.

      Standard ignition timing:
      8 to 12° BTDC idling (transmission in neutral and A/C switch off)

    4. Remove SST from the DLC3.

    5. Inspect the ignition timing during idling.

      Standard ignition timing:
      7 to 24° BTDC idling (transmission in neutral and A/C switch off)

    6. Disconnect the timing light from the engine.


43. INSPECT ENGINE IDLING SPEED

NOTICE:
  1. Turn all the electrical systems off.
  1. Perform the inspection when the cooling fan motor is turned off.

  1. Warm up the engine.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

    3. Inspect the engine idling speed.

      Standard idling speed:
      650 to 750 rpm (transmission in neutral and A/C switch off)

  1. A206183E06
    When not using the intelligent tester:
    Text in Illustration 
    *a
    Front view of DLC3:

    1. Connect SST to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Inspect the engine idling speed.

      Standard idling speed:
      650 to 750 rpm (transmission in neutral and A/C switch off)


44. INSPECT COMPRESSION
  1. Warm up and stop the engine.

  1. Remove the 6 spark plugs (Click here).

  1. Disconnect the 6 fuel injector connectors.

  1. Inspect the cylinder compression pressure.

    1. Insert a compression gauge into the spark plug hole (Procedure "A").

    2. While cranking the engine, measure the compression pressure (Procedure "B").

      Compression pressure:
      1400 kPa (14.3 kgf/cm2, 203 psi) or higher

      Minimum pressure:
      1100 kPa (11.2 kgf/cm2, 160 psi) or less

      Difference between each cylinder:
      100 kPa (1.0 kgf/cm2, 15 psi)

      HINT:
      1. Use a fully-charged battery so that the engine speed can be increased to 250 rpm or more.
      2. Measure the compression in as short a time as possible.

    3. Repeat procedures "A" and "B" for each cylinder.

    4. If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and repeat procedures "A" and "B" for cylinders with low compression.

      1. If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
      2. If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage from the gasket.

  1. Connect the 6 injector connectors.

  1. Install the 6 spark plugs (Click here).


45. INSPECT CO/HC

HINT:
This check is to determine whether or not the idle CO/HC concentration complies with regulations.

  1. Start the engine.

  1. Run the engine at 2500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.31 ft) into the tailpipe during idling.

  1. Immediately check the CO/HC concentration during idling and/or at 2500 rpm.

    HINT:
    When carrying out the 2 tests (idling and 2500 rpm), the measurement orders are prescribed by the applicable local regulations.

  1. If the CO/HC concentration does not comply with regulations, perform troubleshooting in the order given below.

    1. Check the A/F sensor operation (Click here) and heated oxygen sensor operation (Click here).

    2. See the table below for possible causes, and then inspect and correct the corresponding causes if necessary.

      CO
      HC
      Symptom
      Causes
      Normal
      High
      Rough idling
      1. Faulty ignition:
        1. Incorrect timing
        2. Plugs are contaminated or shorted, or plug gaps are incorrect
      2. Incorrect valve clearance
      3. Leaky intake and exhaust valves
      4. Leaky cylinders
      Low
      High
      Rough idling
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. Ventilation hoses
        2. Intake manifold
        3. Throttle body
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective engine coolant temperature sensor
        3. Faulty mass air flow meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle position sensor


46. INSTALL V-BANK COVER
  1. Engage the 2 V-bank cover hooks to the bracket.

  1. Align the 2 V-bank cover grommets with the 2 pins and press down on the V-bank cover to engage the pins.


47. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here).
← INSTALLATION (Nov 2010 – Oct 2012)INSTALLATION (Aug 2013 – Jul 2014) →