REMOVAL
Removal / installation · Vehicles built Jul 2007 – Jul 2009
| 1. REMOVE BATTERY |
| 2. DRAIN ENGINE COOLANT |
![]() ![]() |
- CAUTION:
- To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.
Remove the service hole cover from the engine under cover.
Install a vinyl hose onto the drain on the radiator side.
Fix the vinyl hose with tape.
Loosen the 3 drain plugs on the engine and radiator, and drain the coolant.

Remove the radiator cap.
Drain the coolant from the reservoir tank.
Tighten the 3 drain plugs.
- Torque:
- 13 N*m{ 130 kgf*cm , 9 ft.*lbf } for the engine
Remove the vinyl hose from the radiator.
| 3. DRAIN ENGINE OIL |
Remove engine under cover seal No. 3.
Remove the oil pan drain plug and drain the engine oil.
Clean the oil pan drain plug and install it with a new gasket.
- Torque:
- 40 N*m{ 408 kgf*cm , 30 ft.*lbf }
| 4. REMOVE POWER STEERING LINK ASSEMBLY |
| 5. REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY |
| 6. REMOVE FAN |
| 7. REMOVE GENERATOR ASSEMBLY |
| 8. SEPARATE COOLER COMPRESSOR ASSEMBLY |
![]() ![]() |
Remove the bolt, then separate the suction hose sub-assembly.
Disconnect the cooler compressor assembly connector.

Remove the 4 bolts, then separate the cooler compressor assembly from the V-ribbed belt tensioner assembly.
| 9. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() ![]() |
Remove the 5 bolts, then remove the V-ribbed belt tensioner.
| 10. REMOVE OIL LEVEL GAUGE GUIDE |
Remove the oil level gauge.
Remove the bolt and pull out the oil level gauge guide.
Remove the O-ring from the oil level gauge guide.
| 11. SEPARATE VANE PUMP ASSEMBLY |
![]() ![]() |
Disconnect the power steering pressure switch connector.
Remove the 2 bolts, then separate the vane pump.
- NOTICE:
- Do not hit the pulley with other parts when separating the vane pump.
- HINT:
- The vane pump is suspended securely.
| 12. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY |
Remove the 2 bolts, then remove the No. 2 idler pulleys.

| 13. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY |
Remove the bolt, then remove the No. 1 idler pulley.

| 14. REMOVE CRANKSHAFT PULLEY |
![]() ![]() |
Using SST, hold the crankshaft pulley and loosen the pulley set bolt.
- SST
- 09213-54015
(91651-60855)
09330-00021
Using the pulley set bolt and SST, remove the crankshaft pulley.

- SST
- 09950-50013
(09951-05010, 09952-05010, 09953-05020, 09954-05030)
| 15. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY |
![]() ![]() |
Remove the 10 bolts and 2 nuts.
Insert the blade of SST between the oil pan and No. 2 oil pan, cut off applied sealer and remove the No. 2 oil pan.

- NOTICE:
- Be careful not to damage the contact surfaces of the oil pan and No. 2 oil pan.
- Be careful not to damage the No. 2 oil pan flange.
- Be careful not to damage the contact surfaces of the oil pan and No. 2 oil pan.
| 16. REMOVE OIL STRAINER SUB-ASSEMBLY |
![]() ![]() |
Remove the 2 nuts, then remove the oil strainer and gasket.
| 17. REMOVE OIL PAN SUB-ASSEMBLY |
![]() ![]() |
Remove the 4 housing bolts.
Remove the flywheel housing under cover.
Remove the 17 bolts and 2 nuts.

Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block.

- NOTICE:
- Be careful not to damage the contact surfaces of the cylinder block and oil pan.
Remove the O-ring from the oil pump.
| 18. REMOVE AIR CLEANER ASSEMBLY |
![]() ![]() |
Disconnect the No. 2 ventilation hose.
Disconnect the vacuum hose.

Disconnect the mass air flow meter connector.
Disengage the 2 wire harness clamps.
Loosen the 2 hose clamps.

Remove the 2 bolts.
Disconnect the air cleaner hose and remove the air cleaner.
| 19. REMOVE THROTTLE BODY BRACKET |
Remove the 2 bolts and the throttle body bracket.

| 20. REMOVE OIL BAFFLE PLATE |
Remove the bolt and the oil baffle plate.

| 21. REMOVE NO. 1 SURGE TANK STAY |
Remove the 2 bolts and the No. 1 surge tank stay.

| 22. REMOVE NO. 2 SURGE TANK STAY |
Remove the 2 bolts and the No. 2 surge tank stay.

| 23. REMOVE INTAKE AIR SURGE TANK |
Disconnect the 2 water by-pass hoses.

Disconnect the fuel vapor feed hose.

Disconnect the ventilation hose.

Disconnect the 2 VSV connectors.

Disconnect the throttle body with motor connector.
Separate the 3 wire harness clamps and the hose clamp.
Remove the 2 nuts.

Using a socket hexagon wrench 8, remove the 4 bolts, intake air surge tank and the gasket.
| 24. REMOVE IGNITION COIL ASSEMBLY |
![]() ![]() |
For Bank 1:
Disconnect the 3 connectors.
Remove the 3 bolts, then remove the 3 ignition coils.
For Bank 2:

Disconnect the 3 connectors.
Remove the 3 bolts, then remove the 3 ignition coils.
| 25. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() ![]() |
Disconnect the 2 connectors.
Remove the 2 bolts, then remove the 2 camshaft timing oil control valves.
| 26. REMOVE VVT SENSOR |
![]() ![]() |
Bank 1 side VVT sensor:
Disconnect the VVT sensor connector.
Remove the bolt and VVT sensor.
Bank 2 side VVT sensor:

Disconnect the No. 4 water by-pass hose and No. 5 water by-pass hose.
Disconnect the VVT sensor connector.
Remove the bolt and VVT sensor.

| 27. REMOVE WATER INLET |
Disconnect the 2 oil cooler hoses. (w/ Oil Cooler)

Disconnect the 2 radiator hoses.
Disconnect the 5 water by-pass hoses.

Remove the 5 bolts and water inlet.

Remove the O-ring from the water outlet pipe.
Remove the gasket from the water pump.
| 28. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() ![]() |
Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.
| 29. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH |
![]() ![]() |
Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.
| 30. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY |
Remove the 24 bolts and 2 nuts.

Remove the timing chain cover by prying between the timing chain cover, cylinder head or cylinder block with a screwdriver.

- NOTICE:
- Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.
Remove the O-ring from the LH cylinder head.
| 31. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL |
![]() ![]() |
Using a screwdriver with its tip wrapped in protective tape, pry out the oil seal.
- NOTICE:
- Do not damage the oil pump assembly.
| 32. SET NO. 1 COMPRESSION TO TDC/COMPRESSION |
![]() ![]() |
Using the crankshaft pulley set bolt, turn the crankshaft to align the crankshaft set key with the timing line of the cylinder block.
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.

If not, turn the crankshaft 1 complete revolution (360°) and align the timing marks as above.
| 33. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY |
- NOTICE:
- Never rotate the crankshaft with the chain tensioner removed.
- When rotating the camshaft with the timing chain removed, rotate the crankshaft counterclockwise 40° from the TDC first.
- Never rotate the crankshaft with the chain tensioner removed.
While turning the stopper plate of the tensioner upward, push in the plunger of the chain tensioner as shown in the illustration.

While turning the stopper plate of the tensioner downward, insert a bar of φ 3.5 mm (0.138) into the holes in the stopper plate and tensioner to fix the stopper plate.
Remove the 2 bolts, then remove the chain tensioner.
| 34. REMOVE CHAIN TENSIONER SLIPPER |
| 35. REMOVE NO. 1 IDLE GEAR |
![]() ![]() |
Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.
| 36. REMOVE NO. 2 CHAIN VIBRATION DAMPER |
Remove the 2 No. 2 chain vibration dampers.
| 37. REMOVE CHAIN SUB-ASSEMBLY |

















