Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM
Turn Signal Light Circuit
Circuit diagnosis · Vehicles built Nov 2010 – Jul 2014
Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2014 from Aug 2014
DESCRIPTION
The turn signal flasher relay turns on when it receives signals from the headlight dimmer switch integrated with the turn signal switch, causing the turn signal lights to flash. WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.
1. CHECK OPERATION (TURN SIGNAL LIGHT)
When the turn signal light switch is operated, check that the appropriate turn signal light flashes.
Result
Result
Proceed to
No lights flash
A
Front turn signal light (LH or RH) does not flash
B
Rear turn signal light (LH or RH) does not flash*1
C
Rear turn signal light (LH or RH) does not flash*2
D
Side turn signal light (LH or RH) does not flash*3
E
*1: w/o Rear Fog Light
*2: w/ Rear Fog Light
*3: w/ Side Turn Signal Light
A
2. INSPECT TURN SIGNAL FLASHER ASSEMBLY
Inspect the turn signal flasher assembly (Click here ).
NG
REPLACE TURN SIGNAL FLASHER ASSEMBLY
OK
3. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER ASSEMBLY - BATTERY, IGNITION SWITCH AND BODY GROUND)
Disconnect the E9 turn signal flasher assembly connector.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E9-1 (IG) - Body ground
Ignition switch ON
11 to 14 V
E9-4 (B) - Body ground
Always
11 to 14 V
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
E9-7 (E) - Body ground
Always
Below 1 Ω
Text in Illustration
*a
Front view of wire harness connector (to Turn Signal Flasher Assembly)
Reconnect the turn signal flasher relay connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
4. INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (TURN SIGNAL LIGHT SWITCH)
Inspect the headlight dimmer switch assembly (Click here ).
NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here )
OK
5. CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - TURN SIGNAL FLASHER ASSEMBLY)
for LHD
Disconnect the E20 headlight dimmer switch assembly connector.
for RHD
Disconnect the E89 headlight dimmer switch assembly connector.
Disconnect the E9 turn signal flasher assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for LHD
Tester Connection
Condition
Specified Condition
E20-2 (TB) - E9 -7 (E)
Always
Below 1 Ω
E20-1 (TL) - E9-5 (EL)
Always
Below 1 Ω
E20-1 (TL) - Body ground
Always
10 kΩ or higher
E20-3 (TR) - E9-6 (ER)
Always
Below 1 Ω
E20-3 (TR) - Body ground
Always
10 kΩ or higher
for RHD
Tester Connection
Condition
Specified Condition
E89-7 (TB) - E9 -7 (E)
Always
Below 1 Ω
E89-6 (TL) - E9-5 (EL)
Always
Below 1 Ω
E89-6 (TL) - Body ground
Always
10 kΩ or higher
E89-8 (TR) - E9-6 (ER)
Always
Below 1 Ω
E89-8 (TR) - Body ground
Always
10 kΩ or higher
Reconnect the turn signal flasher assembly connector.
Reconnect the headlight dimmer switch assembly connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT DIMMER SWITCH - BODY GROUND)
6. CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - TURN SIGNAL FLASHER ASSEMBLY AND BODY GROUND)
Disconnect the A16 and A20 headlight assembly connectors.
Disconnect the E9 turn signal flasher assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
A20-3 - E9-2 (LR)
Always
Below 1 Ω
A20-3 - Body ground
Always
10 kΩ or higher
A20-2 - Body ground
Always
Below 1 Ω
A16-3 - E9-3 (LL)
Always
Below 1 Ω
A16-3 - Body ground
Always
10 kΩ or higher
A16-2 - Body ground
Always
Below 1 Ω
Reconnect the turn signal flasher assembly connector.
Reconnect the headlight assembly connectors.
Result
Result
Proceed to
NG
A
OK (w/o Headlight Leveling)
B
OK (w/ Headlight Leveling)
C
B
C
A
REPAIR OR REPLACE HARNESS OR CONNECTOR
7. CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - TURN SIGNAL FLASHER ASSEMBLY AND BODY GROUND)
Disconnect the L12 and L15 rear combination light assembly connectors.
Disconnect the E9 turn signal flasher assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
L15-1 - E9-2 (LR)
Always
Below 1 Ω
L15-1 - Body ground
Always
10 kΩ or higher
L15-2 - Body ground
Always
Below 1 Ω
L12-1 - E9-3 (LL)
Always
Below 1 Ω
L12-1 - Body ground
Always
10 kΩ or higher
L12-2 - Body ground
Always
Below 1 Ω
Reconnect the turn signal flasher assembly connector.
Reconnect the rear combination light assembly connectors.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE REAR COMBINATION LIGHT ASSEMBLY (Click here )
8. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT ASSEMBLY - TURN SIGNAL FLASHER ASSEMBLY AND BODY GROUND)
Disconnect the N2 and N3 rear fog light assembly connectors.
Disconnect the E9 turn signal flasher assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
N2-1 - E9-2 (LR)
Always
Below 1 Ω
N2-1 - Body ground
Always
10 kΩ or higher
N2-2 - Body ground
Always
Below 1 Ω
N3-1 - E9-3 (LL)
Always
Below 1 Ω
N3-1 - Body ground
Always
10 kΩ or higher
N3-2 - Body ground
Always
Below 1 Ω
Reconnect the turn signal flasher assembly connector.
Reconnect the rear fog light assembly connectors.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
9. CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - TURN SIGNAL FLASHER ASSEMBLY AND BODY GROUND)
Disconnect the A33 and A36 side turn signal light assembly connectors.
Disconnect the E9 turn signal flasher assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
A33-2 - E9-2 (LR)
Always
Below 1 Ω
A33-2 - Body ground
Always
10 kΩ or higher
A33-1 - Body ground
Always
Below 1 Ω
A36-2 - E9-3 (LL)
Always
Below 1 Ω
A36-2 - Body ground
Always
10 kΩ or higher
A36-1 - Body ground
Always
Below 1 Ω
Reconnect the turn signal flasher assembly connector.
Reconnect the side turn signal light assembly connectors.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY (Click here )