2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Turn Signal Light Circuit

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Jul 2007 – Oct 2010 Nov 2010 – Jul 2014 from Aug 2014

DESCRIPTION

The turn signal flasher relay turns on when it receives signals from the headlight dimmer switch integrated with the turn signal switch, causing the turn signal lights to flash.

WIRING DIAGRAM

E214773E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


1. CHECK OPERATION (TURN SIGNAL LIGHT)
  1. When the turn signal light switch is operated, check that the appropriate turn signal light flashes.

    Result 
    Result
    Proceed to
    No lights flash
    A
    Front turn signal light (LH or RH) does not flash
    B
    Rear turn signal light (LH or RH) does not flash*1
    C
    Rear turn signal light (LH or RH) does not flash*2
    D
    Side turn signal light (LH or RH) does not flash*3
    E
    1. *1: w/o Rear Fog Light
    2. *2: w/ Rear Fog Light
    3. *3: w/ Side Turn Signal Light



B
Go to step 6

C
Go to step 7

D
Go to step 8

E
Go to step 9
A


2. INSPECT TURN SIGNAL FLASHER ASSEMBLY
  1. Inspect the turn signal flasher assembly (Click here).



NG
REPLACE TURN SIGNAL FLASHER ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER ASSEMBLY - BATTERY, IGNITION SWITCH AND BODY GROUND)

  1. E120966E20
    Disconnect the E9 turn signal flasher assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E9-1 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    E9-4 (B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E9-7 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Turn Signal Flasher Assembly)

  1. Reconnect the turn signal flasher relay connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (TURN SIGNAL LIGHT SWITCH)
  1. Inspect the headlight dimmer switch assembly (Click here).



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - TURN SIGNAL FLASHER ASSEMBLY)
  1. for LHD

    1. Disconnect the E20 headlight dimmer switch assembly connector.

  1. for RHD

    1. Disconnect the E89 headlight dimmer switch assembly connector.

  1. Disconnect the E9 turn signal flasher assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    E20-2 (TB) - E9 -7 (E)
    Always
    Below 1 Ω
    E20-1 (TL) - E9-5 (EL)
    Always
    Below 1 Ω
    E20-1 (TL) - Body ground
    Always
    10 kΩ or higher
    E20-3 (TR) - E9-6 (ER)
    Always
    Below 1 Ω
    E20-3 (TR) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    E89-7 (TB) - E9 -7 (E)
    Always
    Below 1 Ω
    E89-6 (TL) - E9-5 (EL)
    Always
    Below 1 Ω
    E89-6 (TL) - Body ground
    Always
    10 kΩ or higher
    E89-8 (TR) - E9-6 (ER)
    Always
    Below 1 Ω
    E89-8 (TR) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the turn signal flasher assembly connector.

  1. Reconnect the headlight dimmer switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT DIMMER SWITCH - BODY GROUND)

6. CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - TURN SIGNAL FLASHER ASSEMBLY AND BODY GROUND)
  1. Disconnect the A16 and A20 headlight assembly connectors.

  1. Disconnect the E9 turn signal flasher assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A20-3 - E9-2 (LR)
    Always
    Below 1 Ω
    A20-3 - Body ground
    Always
    10 kΩ or higher
    A20-2 - Body ground
    Always
    Below 1 Ω
    A16-3 - E9-3 (LL)
    Always
    Below 1 Ω
    A16-3 - Body ground
    Always
    10 kΩ or higher
    A16-2 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the turn signal flasher assembly connector.

  1. Reconnect the headlight assembly connectors.

    Result 
    Result
    Proceed to
    NG
    A
    OK (w/o Headlight Leveling)
    B
    OK (w/ Headlight Leveling)
    C



B
REPLACE HEADLIGHT ASSEMBLY (Click here)

C
REPLACE HEADLIGHT ASSEMBLY (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

7. CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - TURN SIGNAL FLASHER ASSEMBLY AND BODY GROUND)
  1. Disconnect the L12 and L15 rear combination light assembly connectors.

  1. Disconnect the E9 turn signal flasher assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L15-1 - E9-2 (LR)
    Always
    Below 1 Ω
    L15-1 - Body ground
    Always
    10 kΩ or higher
    L15-2 - Body ground
    Always
    Below 1 Ω
    L12-1 - E9-3 (LL)
    Always
    Below 1 Ω
    L12-1 - Body ground
    Always
    10 kΩ or higher
    L12-2 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the turn signal flasher assembly connector.

  1. Reconnect the rear combination light assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR COMBINATION LIGHT ASSEMBLY (Click here)

8. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT ASSEMBLY - TURN SIGNAL FLASHER ASSEMBLY AND BODY GROUND)
  1. Disconnect the N2 and N3 rear fog light assembly connectors.

  1. Disconnect the E9 turn signal flasher assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N2-1 - E9-2 (LR)
    Always
    Below 1 Ω
    N2-1 - Body ground
    Always
    10 kΩ or higher
    N2-2 - Body ground
    Always
    Below 1 Ω
    N3-1 - E9-3 (LL)
    Always
    Below 1 Ω
    N3-1 - Body ground
    Always
    10 kΩ or higher
    N3-2 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the turn signal flasher assembly connector.

  1. Reconnect the rear fog light assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR FOG LIGHT ASSEMBLY (Click here)

9. CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - TURN SIGNAL FLASHER ASSEMBLY AND BODY GROUND)
  1. Disconnect the A33 and A36 side turn signal light assembly connectors.

  1. Disconnect the E9 turn signal flasher assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A33-2 - E9-2 (LR)
    Always
    Below 1 Ω
    A33-2 - Body ground
    Always
    10 kΩ or higher
    A33-1 - Body ground
    Always
    Below 1 Ω
    A36-2 - E9-3 (LL)
    Always
    Below 1 Ω
    A36-2 - Body ground
    Always
    10 kΩ or higher
    A36-1 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the turn signal flasher assembly connector.

  1. Reconnect the side turn signal light assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY (Click here)


← Turn Signal Light Circuit (Nov 2010 – Jul 2014)Hazard Warning Switch Circuit (Jul 2007 – Oct 2010) →