2011-2016 FJ Cruiser · Service Manual BODY ELECTRICAL

Reverse Signal Circuit

Circuit diagnosis · Vehicles built from Aug 2008

DESCRIPTION

The inner rear view mirror assembly receives a reverse signal from the park/neutral position switch or the back-up light switch.

WIRING DIAGRAM

E168284E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. INSPECT INNER REAR VIEW MIRROR ASSEMBLY (REVERSE SIGNAL)

  1. E168285E03
    Disconnect the R6 inner rear view mirror assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R6-3 (REV) - Body ground
    Ignition switch ON,
    shift lever in R
    11 to 14 V
    Ignition switch ON,
    shift lever in P
    Below 1 V

  1. Reconnect the inner rear view mirror assembly connector.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. SYSTEM CHECK
  1. Check the vehicle specifications.

    Result 
    Result
    Proceed to
    Vehicle with automatic transmission
    A
    Vehicle with manual transmission
    B



B
Go to step 5
A


3. INSPECT PARK/NEUTRAL POSITION SWITCH (IG SIGNAL)

  1. E168286E02
    Disconnect the B35 park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B35-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Reconnect the park/neutral position switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (INNER MIRROR - PNP SWITCH)

  1. E168287E02
    Disconnect the R6 inner rear view mirror assembly connector.

  1. Disconnect the B35 park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R6-3 (REV) - B35-1 (R)
    Always
    Below 1 Ω
    R6-3 (REV) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B

  1. Reconnect the inner rear view mirror assembly connector.

  1. Reconnect the park/neutral position switch connector.



B
REPLACE PARK/NEUTRAL POSITION SWITCH (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR

5. INSPECT BACK-UP LIGHT SWITCH (IG SIGNAL)

  1. E168289E02
    Disconnect the B42 back-up light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B42-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Reconnect the back-up light switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (INNER MIRROR - BACK-UP LIGHT SWITCH)

  1. E168290E02
    Disconnect the R6 inner rear view mirror assembly connector.

  1. Disconnect the B42 back-up light switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R6-3 (REV) - B42-1 (R)
    Always
    Below 1 Ω
    R6-3 (REV) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the inner rear view mirror assembly connector.

  1. Reconnect the back-up light switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK-UP LIGHT SWITCH (Click here)


← Back Door Courtesy Switch Circuit (from Nov 2010)Display Signal Circuit between Inner Rear View Mirror Assembly and Television Camera Assembly (from Aug 2008) →