2011-2016 FJ Cruiser · Service Manual BRAKE

C1440/98 Steering Angle Sensor Unusual Bank Angle Detected

Diagnostic trouble codes · Vehicles built Aug 2009 – Oct 2010

Versions by build date: Aug 2008 – Jul 2009 Aug 2009 – Oct 2010

DESCRIPTION

The skid control ECU receives signals from the yaw rate and deceleration sensor via the CAN communication system.
The yaw rate sensor has a built in deceleration sensor and detects the vehicle's condition.
If there is trouble in the bus lines between the yaw rate and deceleration sensor and the CAN communication system, the DTCs U0123/62 (malfunction in CAN communication with the yaw rate sensor) and U0124/95 (malfunction in CAN communication with the deceleration sensor) are output.
DTC Code
DTC Detection Condition
Trouble Area
C1440/98
The skid control ECU detects that the vehicle is driving on a bank at an angle of 30 degrees or more
Yaw rate and deceleration sensor

WIRING DIAGRAM

C190271E08

INSPECTION PROCEDURE

NOTICE:
  1. Before proceeding with the inspection, explain to the customer that the vehicle driving record shows that the vehicle was driven on a bank at an angle of 30°, and confirm that this condition occurred.
  2. When replacing the yaw rate and deceleration sensor, perform zero point calibration (Click here).

HINT:
When U0123/62, U0124/95 and/or U0126/63 is output together with C1232/32, C1234/34, C1243/43, C1244/44, C1245/45, and/or C1381/97, inspect and repair the trouble areas indicated by U0123/62, U0124/95 and/or U0126/63 first (Click here).


1. CHECK DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. At a speed of 30 km/h (19 mph) or more, drive the vehicle, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.

  1. Turn the ignition switch to ON again and check that no CAN communication system DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC (C1440/98) output
    A
    DTC output (relating to CAN communication system)
    B
    DTC output (relating to yaw rate and deceleration sensor)
    C
    DTC not output
    D

    HINT:
    DTC C1440/98 may have been stored because the vehicle was driven on a bank at an angle of 30° or more.



B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)

D
CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)
A


2. CHECK YAW RATE AND DECELERATION SENSOR INSTALLATION
  1. Turn the ignition switch off.

  1. Check that the yaw rate and deceleration sensor has been installed properly (Click here).

    OK:
    The sensor should be tightened to the specified torque.
    The sensor should not be tilted.



NG
INSTALL YAW RATE AND DECELERATION SENSOR CORRECTLY (Click here)
OK


3. READ VALUE USING DATA LIST (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC.

    ABS/VSC/TRAC 
    Tester Display
    Measurement
    Item/Range
    Normal Condition
    Diagnostic Note
    Yaw Rate Open
    Yaw rate sensor open detection /
    ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    Deceleration Open
    Deceleration sensor open detection /
    ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -

    OK:
    There are no momentary interruptions

HINT:
Perform the above inspection before removing the sensor and connector.



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)

4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - YAW RATE AND DECELERATION SENSOR)

  1. C190277E03
    Disconnect the skid control ECU connector.

  1. Disconnect the yaw rate and deceleration sensor connector.

  1. Measure the resistance according to the value(s) in the table below

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-25 (CANL) - E34-2 (CANL)
    Always
    Below 1 Ω
    A4-25 (CANL) - Body ground
    Always
    10 kΩ or higher
    A4-11 (CANH) - E34-3 (CANH)
    Always
    Below 1 Ω
    A4-11 (CANH) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE YAW RATE AND DECELERATION SENSOR (Click here)


← C1440/98 Steering Angle Sensor Unusual Bank Angle Detected (Aug 2008 – Jul 2009)C1442 Invalid Data Received from Acceleration Sensor (+ C1443) (Nov 2010 – Jul 2012) →