2011-2016 FJ Cruiser · Service Manual BRAKE

ABS Warning Light Remains ON

Circuit diagnosis · Vehicles built Nov 2010 – Jul 2011

Versions by build date: Jul 2007 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 from Aug 2011

DESCRIPTION

If any of the following is detected, the ABS warning light remains on.
  1. The skid control ECU connectors are disconnected from the skid control ECU.
  2. There is a malfunction in the skid control ECU internal circuit.
  3. There is an open in the harness between the combination meter and skid control ECU.
  4. The anti-lock brake system is defective.
  5. The voltage at terminal IG1 is high.
  6. The rear differential is locked.*
*: w/ Rear Differential Lock

HINT:
It may not be possible to use the intelligent tester when the skid control ECU is abnormal.


WIRING DIAGRAM

C231256E02

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK THAT SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check the skid control ECU connector connection.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


2. CHECK DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


3. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


4. READ VALUE USING INTELLIGENT TESTER (IG1 VOLTAGE VALUE)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Start the engine.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item : Range
    Normal Condition
    Diagnostic Note
    IG1 Voltage Value
    IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V
    11 to 14 V
    Changes in proportion to battery voltage

  1. Measure the voltage output from the ECU displayed on the tester.

    Result 
    Result
    Proceed
    Data display is within Normal Condition
    A
    Data display is not within Normal Condition
    B



NG
Go to step 7
OK


5. INSPECT SKID CONTROL ECU (EXI3 TERMINAL)

  1. for w/ Rear Differential Lock

    1. Disconnect the A4 skid control ECU connector.

    2. C214161E52
      Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A4-40 (EXI3) - Body ground
      Ignition switch ON
      w/ Rear Differential Lock: Rear differential free
      11 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Skid Control ECU)

  1. for w/o Rear Differential Lock

    1. Disconnect the A4 skid control ECU connector.

    2. C214161E52
      Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A4-40 (EXI3) - Body ground
      Ignition switch ON
      11 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Skid Control ECU)
      Result 
      Result
      Proceed to
      OK
      A
      NG (for w/ Rear Differential Lock)
      B
      NG (for w/o Rear Differential Lock)
      C



B
Go to step 9

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


6. READ VALUE USING INTELLIGENT TESTER (ABS WARNING LIGHT)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the tester, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ABS Warning Light
    ABS warning light/ ON or OFF
    ON: warning on
    OFF: warning off
    -
    Result 
    Result
    Proceed to
    ABS Warning light remains on, Data Monitor is on.
    A
    ABS Warning light remains on, Data Monitor is off.
    B



B
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)

7. INSPECT SKID CONTROL ECU (IG1 TERMINAL)
  1. Disconnect the skid control ECU connector.

  1. C214161E51
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A4-46 (IG1) - Body ground
    Idling
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. INSPECT SKID CONTROL ECU (GND TERMINAL)

  1. C124799E53
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A4-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A5-4 (GND3) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)

9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI3 CIRCUIT)
  1. Disconnect the A4 skid control ECU connector.

  1. Disconnect the L7 four wheel drive control ECU connector.

  1. Disconnect the D2 rear differential lock indicator switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-40 (EXI3) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH)
  1. Remove the rear differential lock detection switch (Click here).

  1. C214518E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 - 1
    Pushed in
    Below 1 Ω
    Not pushed in
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Differential Lock Indicator Switch)



NG
REPLACE DIFFERENTIAL LOCK INDICATOR SWITCH (REAR DIFFERENTIAL LOCK DETECTION SWITCH) (Click here)
OK


11. INSPECT SKID CONTROL ECU (EXI3 TERMINAL)
  1. Disconnect the A4 skid control ECU connector.

  1. Connect the L7 four wheel drive control ECU connector.

  1. C214161E53
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-40 (EXI3) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPLACE 4 WHEEL DRIVE CONTROL ECU NO.2
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)


← ABS Warning Light Remains ON (Aug 2009 – Oct 2010)ABS Warning Light Remains ON (from Aug 2011) →