2011-2016 FJ Cruiser · Service Manual BRAKE

VSC OFF Indicator Light does not Come ON

Circuit diagnosis · Vehicles built Nov 2010 – Jul 2011

Versions by build date: Jul 2007 – Jul 2008 Aug 2008 – Jul 2009 Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Oct 2012 from Nov 2012

DESCRIPTION

Refer to VSC OFF Indicator Light Remains ON (Click here).

WIRING DIAGRAM

Refer to VSC OFF Indicator Light Remains ON (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).


1. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    TRAC/VSC Off Mode
    TRAC/VSC off mode/ Normal, TRC OFF or VSC OFF
    Normal: Normal mode
    TRC OFF: TRAC OFF mode
    VSC OFF: VSC OFF mode
    -

  1. Check that the mode display changes according to VSC OFF switch operation.

    OK:
    Display changes according to switch operation.



NG
Go to step 3
OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

3. INSPECT VSC OFF SWITCH
  1. Remove the VSC OFF switch (Click here).

  1. C234071E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3-4
    Switch is not pushed
    10 kΩ or higher
    Switch is pushed
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (VSC OFF Switch)



NG
REPLACE VSC OFF SWITCH (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
  1. Disconnect the A4 skid control ECU connector.

  1. Disconnect the E77 VSC OFF switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-9 (CSW) - E77-3
    Always
    Below 1 Ω
    A4-9 (CSW) - Body ground
    Always
    10 kΩ or higher
    E77-4 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)


← VSC OFF Indicator Light does not Come ON (Aug 2009 – Oct 2010)VSC OFF Indicator Light does not Come ON (Aug 2011 – Jul 2012) →