Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0011    Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)

DTC    P0012    Camshaft Position "A" - Timing Over-Retarded (Bank 1)

DTC    P0021    Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2)

DTC    P0022    Camshaft Position "A" - Timing Over-Retarded (Bank 2)

for Preparation Click here


DESCRIPTION

Refer to DTC P0010 .

DTC No.
DTC Detection Condition
Trouble Area
P0011
P0021
Intake valve timing is not adjusted in the valve timing advance range (1 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for intake side of bank 1, 2)
  3. Oil control valve filter
  4. Camshaft timing gear assembly
  5. ECM
P0012
P0022
Intake valve timing is not adjusted in the valve timing retard range (2 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for intake side of bank 1, 2)
  3. Oil control valve filter
  4. Camshaft timing gear assembly
  5. ECM

MONITOR DESCRIPTION

  1. The ECM optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, Camshaft Timing Oil Control Valve (OCV) assembly and camshaft timing gear assembly. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the camshaft timing gear assembly. The camshaft timing gear assembly can advance or retard the intake camshaft.
  2. If the difference between the target and actual intake valve timings is large, and changes in the actual intake valve timing are small, the ECM interprets this as the camshaft timing gear assembly stuck malfunction and stores DTC(s).
  3. DTC P0011 and P0021 (Advanced Cam Timing) are subject to 1 trip detection logic.
  4. DTC P0012 and P0022 (Retarded Cam Timing) are subject to 2 trip detection logic.
  5. Example:
    A DTC is stored when the following conditions 1 and 2 are met:
    1. It takes 5 seconds or more to change the valve timing by 5°CA.
    2. After the above condition 1 is met, the OCV is forcibly activated for 10 seconds.
  6. These DTCs indicate that the VVT controller cannot operate properly due to OCV malfunctions or the presence of foreign objects in the OCV.

MONITOR STRATEGY


Related DTCs
P0011: Advanced camshaft timing (Bank 1)
P0012: Retarded camshaft timing (Bank 1)
P0021: Advanced camshaft timing (Bank 2)
P0022: Retarded camshaft timing (Bank 2)
Required Sensors/Components (Main)
VVT oil control valve and VVT Actuator
Required Sensors/Components (Related)
Crankshaft position sensor, VVT sensor and Engine coolant temperature sensor
Frequency of Operation
Continuous
Duration
Within 10 seconds
MIL Operation
Advanced camshaft timing: Immediate
Retarded camshaft timing: 2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT oil control valve)
P0016, P0018 (VVT system - misalignment)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
Battery voltage
11 V or more
Engine speed
400 to 4000 rpm
ECT
75 to 100°C (167 to 212°F)

TYPICAL MALFUNCTION THRESHOLDS


Advanced camshaft timing: 
All of following conditions are met
-
Deviation of actual valve timing and target valve timing
More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit.
Valve timing
No change at advanced valve timing

Retarded camshaft timing: 
All of following conditions are met
-
Deviation of actual valve timing and target valve timing
More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit.
Valve timing
No change at retarded valve timing
  1. If the difference between the target and actual camshaft timings is more than the specified value, the ECM operates the VVT actuator.
  2. Then, the ECM monitors the camshaft timing change for 10 seconds.

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN


A232050E28

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
  7. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Idle the engine for 3 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0011, P0012, P0021 or P0022.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].

  14. Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Depress the accelerator pedal by a large amount.

  15. Idle the engine for 3 minutes or more [G].
  16. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].
  17. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  18. Check the DTC judgment result again.

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the following procedure.

  19. Perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0010 .

INSPECTION PROCEDURE


HINT:

Abnormal Bank
Advanced Timing Over
(Valve Timing is Out of Specified Range)
Retarded Timing Over
(Valve Timing is Out of Specified Range)
Bank 1
P0011
P0012
Bank 2
P0021
P0022
  1. If DTC P0011 or P0012 is output, check the right bank VVT system for intake side circuit (for Bank 1).
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. If DTC P0021 or P0022 is output, check the left bank VVT system for intake side circuit (for Bank 2).
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  5. DTC P0011, P0012, P0021 or P0022 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.
  6. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0011, P0012, P0021 or P0022 is output
    A
    P0011, P0012, P0021 or P0022 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0011, P0012, P0021 or P0022 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV FOR INTAKE SIDE)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the Techstream on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).

  1. Check the engine speed while operating the OCV using the Techstream.

    OK:
    Techstream Operation
    Specified Condition
    0%
    Normal engine speed
    100%
    Engine idles roughly or stalls

    HINT:
    Refer to "Data List / Active Test" [VVT OCV Duty #1, VVT Change Angle #1, VVT OCV Duty #2 and VVT Change Angle #2] (Click here).



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read pending DTCs.

OK:
No pending DTC output.



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TOOTH OF TIMING CHAIN)


    A135015E07
  1. Remove the cylinder head cover sub-assemblies RH and LH.

  1. Turn the crankshaft to align the alignment mark of the crankshaft.

  1. Align the notch of the crankshaft pulley to the "0" position.

  1. Check if the alignment marks of the camshaft pulley and camshaft bearing cap align.
    Text in Illustration 
    *1
    Alignment Mark

  1. Turn the crankshaft clockwise 360° if the alignment marks do not align. Check if they align once again.

    OK:
    The alignment marks of the camshaft pulley and the camshaft bearing cap align when the notch of the crankshaft pulley is in the "0" position.



NG
ADJUST VALVE TIMING (Click here)
OK


5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE)
  1. Inspect the camshaft timing oil control valve assembly (for intake side) (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE) (Click here)
OK


6.INSPECT OIL CONTROL VALVE FILTER
  1. Remove the oil control valve filter (Click here).

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.



NG
CLEAN OR REPLACE OIL CONTROL VALVE FILTER
OK


7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Replace the camshaft timing gear assembly .

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft timing gear assembly (Click here).


NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read pending DTCs.

    OK:
    No pending DTC is output.

HINT:
DTC P0011, P0012, P0021 or P0022 is output when foreign objects in engine oil are caught in some part of the system. These codes will stay output for a short time even after the system returns to normal. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



NG
REPLACE ECM (Click here)
OK

END