Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0230    Fuel Pump Primary Circuit

for Preparation Click here


DESCRIPTION

HINT:
This DTC P0230 is applicable to Mexico Models only.

When a malfunction in the fuel pump circuit is detected, DTC P0230 is stored.
The fuel pump circuit consists of the ECM, fuel pump and fuel pump control ECU assembly (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU assembly. Based on the signal sent from the ECM, the fuel pump control ECU assembly adjusts the fuel pump operation speed among 3 settings. The fuel pump control ECU assembly also has a self-diagnosis function. Based on the fuel pump circuit condition, the fuel pump control ECU assembly outputs a diagnostic signal (DI) to the ECM, and the ECM determines if there is a malfunction in the fuel pump circuit.

DTC No.
DTC Detection Condition
Trouble Area
P0230
Either condition is met (1 trip detection logic):
  1. When the fuel pump is operating:
    1. Amount of remaining fuel is 17 L (18 US qts, 15 Imp. qts) or more.
    2. DI terminal output is low.
  2. When the fuel pump is not operating:
    1. DI terminal output is high.
  1. Open or short in fuel pump circuit
  2. Fuel pump
  3. Fuel pump control ECU assembly
  4. ECM

MONITOR DESCRIPTION

To monitor the fuel pump circuit, the ECM checks the fuel pump control signal (FPC) and diagnostic signal (DI). The FPC voltage varies between approximately 0 V and approximately 12 V (duty signal). Based on the condition of the fuel pump control ECU assembly malfunction, the DI voltage varies between approximately 0 V and approximately 12 V. The ECM then compares the variance of the FPC voltage and DI voltage, and determines if the fuel pump circuit is malfunctioning. When the ECM determines that the fuel pump circuit is malfunctioning, a DTC is stored immediately.

WIRING DIAGRAM

Refer to Fuel Pump Control Circuit .

INSPECTION PROCEDURE

This troubleshooting procedure is based on the premise that the engine can be started. If the engine cannot be started, proceed to Problem Symptoms Table (Click here).

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

1.CHECK FOR DTC (B1500)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Trouble Codes.

  1. Read DTCs.

    OK:
    B1500 is not output.



NG
GO TO DTC B1500 (Click here)
OK


2.PERFORM ACTIVE TEST USING TECHSTREAM (FUEL PUMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. Check whether operating sounds can be heard while operating the fuel pump using the Techstream.

    OK:
    Operating sounds can be heard from fuel pump.



NG
Go to step 6
OK


3.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM, BODY GROUND)
  1. Disconnect the O1 fuel pump control ECU assembly connector.

  1. Disconnect the E78 and E77 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    O1-1 (FPC) - E78-3 (FPC)
    Always
    Below 1 Ω
    O1-2 (DI) - E77-26 (DI)
    Always
    Below 1 Ω
    O1-3 (E) - Body ground
    Always
    Below 1 Ω
    O1-1 (FPC) or E78-3 (FPC) - Body ground
    Always
    10 kΩ or higher
    O1-2 (DI) or E77-26 (DI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
  1. Replace the fuel pump control ECU assembly (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0230)
  1. Check that there are 17 liters (18 US qts, 15 Imp. qts) or more of fuel remaining.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Start the engine and idle it for 5 minutes.

  1. Drive the vehicle in an urban area for approximately 10 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    OK:
    DTC P0230 is not output.



NG
REPLACE ECM (Click here)
OK

END 

6.INSPECT CIRCUIT OPENING RELAY (C/OPN)
A126370
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE CIRCUIT OPENING RELAY (C/OPN) (Click here)
OK


7.INSPECT CIRCUIT OPENING RELAY (C/OPN) (POWER SOURCE VOLTAGE)
A241853E01
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (Circuit opening relay (C/OPN)) - Body ground
    Ignition switch ON
    11 to 14 V
    5 (Circuit opening relay (C/OPN)) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    Circuit Opening Relay (C/OPN)



NG
Go to step 14
OK


8.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - ECM, FUEL PUMP CONTROL ECU ASSEMBLY)
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Disconnect the E77 ECM connector.

  1. Disconnect the O1 fuel pump control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1 (Circuit opening relay (C/OPN)) - E77-8 (FC)
    Always
    Below 1 Ω
    3 (Circuit opening relay (C/OPN)) - O1-4 (+B)
    Always
    Below 1 Ω
    1 (Circuit opening relay (C/OPN)) or E77-8 (FC) - Body ground
    Always
    10 kΩ or higher
    3 (Circuit opening relay (C/OPN)) or O1-4 (+B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP CONTROL ECU ASSEMBLY)
  1. Disconnect the L5 fuel pump connector.

  1. Disconnect the O2 fuel pump control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    L5-4 - O2-1 (FP)
    Always
    Below 1 Ω
    L5-5 - O2-2 (FP-)
    Always
    Below 1 Ω
    L5-4 or O2-1 (FP) - Body ground
    Always
    10 kΩ or higher
    L5-5 or O2-2 (FP-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).



NG
REPLACE FUEL PUMP (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM, BODY GROUND)
  1. Disconnect the O1 fuel pump control ECU assembly connector.

  1. Disconnect the E78 and E77 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    O1-1 (FPC) - E78-3 (FPC)
    Always
    Below 1 Ω
    O1-2 (DI) - E77-26 (DI)
    Always
    Below 1 Ω
    O1-3 (E) - Body ground
    Always
    Below 1 Ω
    O1-1 (FPC) or E78-3 (FPC) - Body ground
    Always
    10 kΩ or higher
    O1-2 (DI) or E77-26 (DI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
  1. Replace the fuel pump control ECU assembly (Click here).


NEXT


13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0230)
  1. Check that there are 17 liters (18 US qts, 15 Imp. qts) or more of fuel remaining.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Start the engine and idle it for 5 minutes.

  1. Drive the vehicle in an urban area for approximately 10 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    OK:
    DTC P0230 is not output.



NG
REPLACE ECM (Click here)
OK

END 

14.CHECK HARNESS AND CONNECTOR (CIRCUIT OPENING RELAY (C/OPN) - EFI RELAY, IGNITION SWITCH)
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Remove the EFI relay (EFI) from the engine room relay block.

  1. Disconnect the A1 ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    5 (Circuit opening relay (C/OPN)) - 3 (EFI relay)
    Always
    Below 1 Ω
    2 (Circuit opening relay (C/OPN)) - A1-6 (IG2)
    Always
    Below 1 Ω
    5 (Circuit opening relay (C/OPN)) or 3 (EFI relay) - Body ground
    Always
    10 kΩ or higher
    2 (Circuit opening relay (C/OPN)) or A1-6 (IG2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)