Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Door Courtesy Switch Circuit

for Preparation Click here


DESCRIPTION

The main body ECU detects the condition of each door courtesy switch.

WIRING DIAGRAM


E219934E03


E219935E02


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (DOOR COURTESY SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List /

  1. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Luggage Courtesy SW
    Back door and back window courtesy switch signal/ ON or OFF
    ON: Either back door or back window is open
    OFF: Both back door and back window are closed
    -
    D Door Courtesy SW
    Driver side door courtesy light switch signal/ ON or OFF
    ON: Driver side door is open
    OFF: Driver side door is closed
    -
    P Door Courtesy SW
    Passenger side door courtesy light switch signal/ ON or OFF
    ON: Passenger side door is open
    OFF: Passenger side door is closed
    -
    Rear Door Courtesy SW
    Rear door courtesy light switch signal/ ON or OFF
    ON: Rear door is open
    OFF: Rear door is closed
    -

    OK:
    Condition sign can be displayed.

    Result 
    Result
    Proceed to
    OK
    A
    Front door courtesy switch (driver side) does not operate
    B
    Front door courtesy switch (passenger side) does not operate
    C
    Both rear door courtesy switches do not operate
    D
    Back door courtesy switch or back window courtesy switch does not operate
    E



B
Go to step 2

C
Go to step 4

D
Go to step 6

E
Go to step 8
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FRONT DOOR COURTESY SWITCH (DRIVER SIDE)
  1. Inspect the front door courtesy switch (driver side) (Click here).



NG
REPLACE FRONT DOOR COURTESY SWITCH (DRIVER SIDE) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY SWITCH (DRIVER SIDE) - MAIN BODY ECU)
  1. Disconnect the J1 front door courtesy switch (driver side) connector.

  1. Disconnect the E7 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J1-1 - E7-23 (DCTY)
    Always
    Below 1 Ω
    J1-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the front door courtesy switch (driver side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

4.INSPECT FRONT DOOR COURTESY SWITCH (PASSENGER SIDE)
  1. Inspect the front door courtesy switch (passenger side) (Click here).



NG
REPLACE FRONT DOOR COURTESY SWITCH (PASSENGER SIDE) (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY SWITCH (PASSENGER SIDE) - MAIN BODY ECU)
  1. Disconnect the I1 front door courtesy switch (passenger side) connector.

  1. Disconnect the E7 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I1-1 - E7-24 (PCTY)
    Always
    Below 1 Ω
    I1-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the front door courtesy switch (passenger side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

6.INSPECT ACCESS PANEL LOCK ASSEMBLY (REAR DOOR COURTESY SWITCH)
  1. Inspect the access panel lower lock assembly LH and RH (Click here).

  1. Inspect the access panel upper lock assembly LH and RH (Click here).

Result 
Result
Proceed to
OK
A
NG (Access panel lower lock assembly)
B
NG (Access panel upper lock assembly)
C


B
REPLACE ACCESS PANEL LOWER LOCK ASSEMBLY (Click here)

C
REPLACE ACCESS PANEL UPPER LOCK ASSEMBLY (Click here)
A


7.CHECK HARNESS AND CONNECTOR (ACCESS PANEL LOCK ASSEMBLY - MAIN BODY ECU AND BODY GROUND)
  1. Disconnect the J2, J3, I2 and I3 access panel lock assembly connectors.

  1. Disconnect the E7 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    LH Side 
    Tester Connection
    Condition
    Specified Condition
    J2-2 - E7-11 (RLCY)
    Always
    Below 1 Ω
    J2-2 - Body ground
    Always
    10 kΩ or higher
    J2-1 - Body ground
    Always
    Below 1 Ω
    J3-1 - E7-11 (RLCY)
    Always
    Below 1 Ω
    J3-1 - Body ground
    Always
    10 kΩ or higher
    J3-2 - Body ground
    Always
    Below 1 Ω
    RH Side 
    Tester Connection
    Condition
    Specified Condition
    I2-2 - E7-12 (RRCY)
    Always
    Below 1 Ω
    I2-2 - Body ground
    Always
    10 kΩ or higher
    I2-1 - Body ground
    Always
    Below 1 Ω
    I3-1 - E7-12 (RRCY)
    Always
    Below 1 Ω
    I3-1 - Body ground
    Always
    10 kΩ or higher
    I3-2 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the main body ECU connector.

  1. Reconnect the access panel lock assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

8.CHECK MULTIPLEX COMMUNICATION SYSTEM
  1. Check if a BEAN communication DTC is output (Click here).
    Result 
    Result
    Proceed to
    BEAN communication DTC is not output
    A
    BEAN communication DTC is output
    B



B
GO TO MULTIPLEX COMMUNICATION SYSTEM (Click here)
A


9.INSPECT BACK DOOR COURTESY SWITCH
  1. Inspect the back door courtesy switch (Click here).



NG
REPLACE BACK DOOR COURTESY SWITCH (Click here)
OK


10.INSPECT BACK WINDOW LOCK (BACK DOOR WINDOW COURTESY SWITCH)
  1. Inspect the back window lock (Click here).



NG
REPLACE BACK WINDOW LOCK (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (BACK DOOR COURTESY SWITCH - MAIN BODY ECU)
  1. Disconnect the L2 back door courtesy switch connector.

  1. Disconnect the E7 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L2-1 - E7-7 (BCTY)
    Always
    Below 1 Ω
    L2-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the back door courtesy switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.CHECK HARNESS AND CONNECTOR (BACK WINDOW LOCK - BACK DOOR ECU AND BODY GROUND)
  1. Disconnect the S6 back window lock connector.

  1. Disconnect the S5 back door ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S6-2 - S5-10 (GCTY)
    Always
    Below 1 Ω
    S6-2 - Body ground
    Always
    10 kΩ or higher
    S6-1 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the back door ECU connector.

  1. Reconnect the back window lock connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.REPLACE MAIN BODY ECU
  1. Temporarily replace the main body ECU with a new or normally functioning one.


NEXT


14.READ VALUE USING TECHSTREAM (LUGGAGE COURTESY SW)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List /

  1. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Luggage Courtesy SW
    Back door and back window courtesy switch signal/ ON or OFF
    ON: Either back door or back window is open
    OFF: Both back door and back window are closed
    -

    OK:
    The display is as specified in the normal condition column.



NG
REPLACE BACK DOOR ECU
OK

END (MAIN BODY ECU IS DEFECTIVE)