VEHICLE STABILITY CONTROL SYSTEM > A-TRAC Indicator Light Remains ON |

| 1.CHECK CAN COMMUNICATION LINE |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).
|
| ||||
| OK | |
| 2.CHECK FOR DTC |
Check for DTCs (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 3.READ VALUE USING TECHSTREAM (A-TRAC INDICATOR LIGHT) |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
Check the condition of the A-TRAC switch by operating the Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| A-TRAC Indicator Light | A-TRAC indicator light/ ON or OFF | ON: Indicator light on OFF: Indicator light off | - |
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING TECHSTREAM |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Perform Active Test of the combination meter using the Techstream (Click here).
Check that the A-TRAC indicator light turns on and off on the combination meter when using the Techstream.
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - A-TRAC SWITCH) |
w/ CRAWL
Disconnect the A4 skid control ECU connector.
Disconnect the M1 A-TRAC switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A4-13 (ATRC) - M1-8 (ATRC) | Always | Below 1 Ω |
| A4-13 (ATRC) - Body ground | Always | 10 k Ω or higher |
| M1-8 (ATRC) - Body ground | Always | 10 k Ω or higher |
| M1-5 (E) - Body ground | Always | Below 1 Ω |
w/o CRAWL
Disconnect the A4 skid control ECU connector.
Disconnect the E15 A-TRAC switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A4-13 (ATRC) - E15-3 | Always | Below 1 Ω |
| A4-13 (ATRC) - Body ground | Always | 10 k Ω or higher |
| E15-3 - Body ground | Always | 10 k Ω or higher |
| E15-4 - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
| OK (w/ CRAWL) | A |
| OK (w/o CRAWL) | B |
| NG | C |
|
| ||||
|
| ||||
| A | |
| 6.INSPECT TRANSFER POSITION SWITCH (A-TRAC SWITCH) |
Remove the A-TRAC switch (Click here).
Inspect the A-TRAC switch (Click here).
|
| ||||
| OK | ||
| ||
| 7.INSPECT TRACTION CONTROL SWITCH NO. 2 (A-TRAC SWITCH) |
Remove the A-TRAC switch (Click here).
Inspect the A-TRAC switch (Click here).
|
| ||||
| OK | ||
| ||