Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > A-TRAC Indicator Light does not Come ON

for Preparation Click here


DESCRIPTION

The A-TRAC does not operate even if the A-TRAC switch is pressed under the following conditions:
  1. The TRAC or VSC system is faulty.
  2. The temperature inside the hydraulic brake booster increases and the A-TRAC operation is suspended.

WIRING DIAGRAM

Refer to A-TRAC Indicator Light Remains ON .

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).

1.CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


2.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


3.READ VALUE USING TECHSTREAM (A-TRAC INDICATOR LIGHT)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

  1. Check the condition of the A-TRAC switch by operating the Techstream.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A-TRAC Indicator Light
    A-TRAC indicator light/ ON or OFF
    ON: Indicator light on
    OFF: Indicator light off
    -

    OK:
    The Techstream displays ON or OFF according to A-TRAC switch operation.



NG
CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - A-TRAC SWITCH)
OK


4.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Perform Active Test of the combination meter using the Techstream (Click here).

  1. Check that the A-TRAC indicator light turns on and off on the combination meter when using the Techstream.

    OK:
    The A-TRAC indicator light turns ON or OFF according to the Techstream operations.



NG
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)  

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - A-TRAC SWITCH)
  1. w/ CRAWL

    1. Disconnect the A4 skid control ECU connector.

    2. Disconnect the M1 A-TRAC switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A4-13 (ATRC) - M1-8 (ATRC)
      Always
      Below 1 Ω
      A4-13 (ATRC) - Body ground
      Always
      10 k Ω or higher
      M1-8 (ATRC) - Body ground
      Always
      10 k Ω or higher
      M1-5 (E) - Body ground
      Always
      Below 1 Ω

  1. w/o CRAWL

    1. Disconnect the A4 skid control ECU connector.

    2. Disconnect the E15 A-TRAC switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A4-13 (ATRC) - E15-3
      Always
      Below 1 Ω
      A4-13 (ATRC) - Body ground
      Always
      10 k Ω or higher
      E15-3 - Body ground
      Always
      10 k Ω or higher
      E15-4 - Body ground
      Always
      Below 1 Ω

      Result 
      Result
      Proceed to
      OK (w/ CRAWL)
      A
      OK (w/o CRAWL)
      B
      NG
      C



B
Go to step 7

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


6.INSPECT TRANSFER POSITION SWITCH (A-TRAC SWITCH)
  1. Remove the A-TRAC switch (Click here).

  1. Inspect the A-TRAC switch (Click here).



NG
REPLACE TRANSFER POSITION SWITCH (A-TRAC SWITCH) (Click here)
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)  

7.INSPECT TRACTION CONTROL SWITCH NO. 2 (A-TRAC SWITCH)
  1. Remove the A-TRAC switch (Click here).

  1. Inspect the A-TRAC switch (Click here).



NG
REPLACE TRACTION CONTROL SWITCH NO. 2 (A-TRAC SWITCH) (Click here)
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)