DTC P219A Bank 1 Air-Fuel Ratio Imbalance |
DTC P219B Bank 2 Air-Fuel Ratio Imbalance |
| DTC No. | DTC Detection Condition | Trouble Area |
| P219A P219B | The difference in air fuel ratios between the cylinders exceeds the threshold. |
|
| Related DTCs | P219A: Air fuel ratio cylinder imbalance monitor (bank 1) P219B: Air fuel ratio cylinder imbalance monitor (bank 2) |
| Required Sensors/Components (Main) | Air fuel ratio sensor Crankshaft position sensor |
| Required Sensors/Components (Related) | Mass air flow meter Engine coolant temperature sensor Vehicle speed sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 seconds: Air fuel ratio sensor monitoring method 30 seconds: Crankshaft position sensor monitoring method |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P0010, P0020 (VVT oil control valve) P0011, P0021 (VVT system - advance) P0012, P0022 (VVT system - retard) P0013, P0023 (Exhaust VVT oil control valve) P0014, P0024 (Exhaust VVT system - advance) P0015, P0025 (Exhaust VVT system - retard) P0016, P0018 (VVT system - misalignment) P0017, P0019 (Exhaust VVT system - misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120 - P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient engine coolant temperature for closed loop fuel control) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351 - P0356 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0412, P0418, P1613 (Secondary air injection system control) P0416, P0417, P2440 - P2445 (Secondary air injection system) P0500 (Vehicle speed sensor) |
| Air fuel ratio sensor status | Activated |
| Engine speed | 1600 rpm or higher, and less than 2400 rpm |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Fuel system status | Closed loop |
| Mass air flow | 44 gm/sec or more, and less than 60 gm/sec (for automatic transmission models) 38 gm/sec or more, and less than 48 gm/sec (for manual transmission models) |
| Vehicle speed | Less than 3 km/h (1.875 mph) |
| Engine speed | 400 rpm or higher, and less than 1100 rpm (for automatic transmission models) 550 rpm or higher, and less than 1050 rpm (for manual transmission models) |
| Engine coolant temperature | 75°C (167°F) or higher |
| Air fuel ratio sensor status | Activated |
| Battery voltage | 11 V or higher |
| Fuel system status | Closed loop |
| Air fuel ratio sensor monitoring method criteria (rich side imbalance) | 0.1212 or more (bank 1) (for automatic transmission models) 0.1386 or more (bank 2) (for automatic transmission models) 0.0918 or more (bank 1) (for manual transmission models) 0.094 or more (bank 2) (for manual transmission models) |
| Crankshaft position sensor monitoring method criteria (lean side imbalance) | 1 or more |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P219A AND/OR P219B) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P219A and/or P219B is output | A |
| DTC P219A and/or P219B and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (FREEZE FRAME DATA) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| DTC stored during idling | It is possible to conclude that the problem was detected due to a "lean imbalance" (detected using crankshaft speed variation). |
| DTC stored while vehicle being driven | It is possible to conclude that the problem was detected due to a "rich imbalance" (detected using the air fuel ratio sensor). |
| NEXT | |
| 3.READ VALUE USING TECHSTREAM (MONITOR RESULT) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / Fuel System / Details / A/F SENSOR DETERMINATION B1, A/F SENSOR DETERMINATION B2, ENGINE SPEED FLUCTUATION AVERAGE B1 and ENGINE SPEED FLUCTUATION AVERAGE B2.
Check the Test Result (A/F SENSOR DETERMINATION B1, A/F SENSOR DETERMINATION B2, ENGINE SPEED FLUCTUATION AVERAGE B1 and ENGINE SPEED FLUCTUATION AVERAGE B2).
| Result | Proceed to |
| A/F SENSOR DETERMINATION is Fail | A |
| A/F SENSOR DETERMINATION and ENGINE SPEED FLUCTUATION AVERAGE are Fail | B |
| ENGINE SPEED FLUCTUATION AVERAGE is Fail | B* |
|
| ||||
| A | |
| 4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / Data List / Cylinder #1 to #6 Misfire Count.
Perform the Control the Injection Volume operation with the engine idling.
Check the misfire counts ("Cylinder #1 Misfire Count" to "Cylinder #6 Misfire Count") while decreasing the injection volume in 5% increments.
| NEXT | |
| 5.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 6.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks.
|
| ||||
| OK | |
| 7.INSPECT SPARK PLUG |
Inspect the spark plug of the cylinder causing the imbalance .
|
| ||||
| OK | |
| 8.CHECK FOR SPARKS AND IGNITION |
Perform a spark test .
|
| ||||
| OK | |
| 9.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 10.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the fuel injector assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B11-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B25-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B10-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B21-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B9-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B18-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Fuel Injector Assembly) |
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM) |
Disconnect the B50 ECM connector.
Disconnect the B11, B25, B10, B21, B9 and B18 fuel injector assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B11-2 - B50-6 (#10) | Always | Below 1 Ω |
| B25-2 - B50-1 (#20) | Always | Below 1 Ω |
| B10-2 - B50-7 (#30) | Always | Below 1 Ω |
| B21-2 - B50-2 (#40) | Always | Below 1 Ω |
| B9-2 - B50-8 (#50) | Always | Below 1 Ω |
| B18-2 - B50-3 (#60) | Always | Below 1 Ω |
| B11-2 or B50-6 (#10) - Body ground | Always | 10 kΩ or higher |
| B25-2 or B50-1 (#20) - Body ground | Always | 10 kΩ or higher |
| B10-2 or B50-7 (#30) - Body ground | Always | 10 kΩ or higher |
| B21-2 or B50-2 (#40) - Body ground | Always | 10 kΩ or higher |
| B9-2 or B50-8 (#50) - Body ground | Always | 10 kΩ or higher |
| B18-2 or B50-3 (#60) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 12.CHECK FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE |
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 13.CHECK FOR CAUSE OF FAILURE |
If the cause of the problem has not been found even after performing the troubleshooting procedure, perform the inspection below.
Check the intake valve for deposits.
| NEXT | |
| 14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
| NEXT | ||
| ||
| 15.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF CYLINDER CAUSING IMBALANCE |
Change the installed spark plug to a spark plug that functions normally.
Perform a spark test .
|
| ||||
| OK | ||
| ||
| 16.CHANGE TO NORMAL IGNITION COIL ASSEMBLY AND CHECK SPARK OF CYLINDER CAUSING IMBALANCE |
Change the ignition coil assembly to an ignition coil assembly that functions normally.
Perform a spark test .
|
| ||||
| OK | ||
| ||