Home › ENGINE ยท 2KD-FTV › ENGINE MECHANICAL › VALVE CLEARANCE

VALVE CLEARANCE > ADJUSTMENT

for Preparation Click here



1. SEPARATE BATTERY NEGATIVE TERMINAL


2. REMOVE ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1)


3. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the radiator cap.



  1. Loosen the radiator drain cock plug and a cylinder block drain cock plug. Then drain the coolant.


    A103477E01



4. REMOVE FAN AND GENERATOR V BELT


    A102808E03
  1. Remove the drive belt by rotating the tensioner pulley in clockwise direction to loosen its tension with the pulley set bolt of the tensioner.



5. REMOVE DIESEL THROTTLE BODY ASSEMBLY
(Click here)


6. REMOVE INJECTION PIPE
(Click here)


7. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A102463
  1. Using a small screwdriver, remove the holder seal by prying the portion between the holder seal and the cutout part of the cylinder head.

  1. Disconnect the ventilation hose.

  1. Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.

    NOTICE:
    After removing the fuel pipe, put a plastic bag and rubber band to prevent dirt and foreign objects over the injectors inlet.



8. REMOVE INJECTOR ASSEMBLY
(Click here)


9. SET NO.1 CYLINDER TO TDC/ COMPRESSION


    A072847E01
  1. Align the matchmarks of the crankshaft pulley and timing gear case cover by rotating the crankshaft in clockwise direction.

    HINT:
    Make sure that both camnoses on the intake side and exhaust side of the cylinder No.1 face upward.



10. INSPECT VALVE CLEARANCE


    A072848E01
  1. Check only the valves indicated.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

    2. Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement of the valve lifter.

      Valve clearance (Cold):
      Intake:
      0.20 to 0.30 mm (0.0079 to 0.0118 in.)
      Exhaust:
      0.35 to 0.45 mm (0.0138 to 0.0177 in.)

  1. Turn the crankshaft by 360° to set the No.4 cylinder to TDC/compression.



    A072849E02
  1. Check only the valves indicated.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

    2. Record the out-of-specification valve clearance measurements. They will be used later to determine the required replacement of the valve lifter.

      Valve clearance (Cold):
      Intake:
      0.20 to 0.30 mm (0.0079 to 0.0118 in.)
      Exhaust:
      0.35 to 0.45 mm (0.0138 to 0.0177 in.)



11. REMOVE TIMING BELT NO.1 COVER
  1. Remove the wire harness clamp.



    A102815
  1. Remove the 6 bolts and timing belt cover No.1.



12. REMOVE TIMING BELT


    A070549E01
  1. Turn the crankshaft in the clockwise direction and align the timing marks as shown in the illustration.



    A070550
  1. Uniformly loosen the 2 bolts, and remove the chain tensioner assembly No.1.

  1. Remove the timing belt.



13. REMOVE CAMSHAFT TIMING PULLEY


    A070695
  1. Remove the bolt for the camshaft timing pulley while holding the camshaft with a monkey wrench.



    A077212E01
  1. Using SST, remove the camshaft timing pulley.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061)



14. REMOVE TIMING BELT IDLER SUB-ASSEMBLY NO.1


    A070696
  1. Using a 10 mm socket hexagonal wrench remove the timing belt idler No.1.



15. REMOVE TIMING BELT NO.2 COVER


    A070697
  1. Remove the 4 bolts and nuts, then remove the timing belt No.2 cover.



16. REMOVE CAMSHAFT


    A070698
  1. Uniformly loosen and remove the 15 camshaft bearing cap bolts in the specified order described in the illustration.

  1. Remove the 5 camshaft bearing caps.

  1. Pull out the oil seal.



    A070699
  1. Remove the camshaft and No.2 camshaft.

    NOTICE:
    1. Do not pry the camshaft.
    2. Do not damage the thrusts of the cylinder head.



17. ADJUST VALVE CLEARANCE
  1. Remove the valve lifters.



    A001082
  1. Using a micrometer, measure the thickness of the removed lifter.

  1. Calculate the thickness of a new lifter so that the valve clearance comes within the specified value.
    A
    Thickness of new lifter
    B
    Thickness of used lifter
    C
    Measured valve clearance

    Valve clearance (Cold):
    for intake A = B + (C - 0.25 mm (0.0098 in.))
    for exhaust A = B + (C - 0.40 mm (0.0158 in.))

  1. Select a new lifter with a thickness as close as possible to the calculated values.

    HINT:
    Valve lifters are available in 35 sizes in increments of 0.020 mm (0.0008 in.), from 5.060 mm (0.1992 in.) to 5.740 mm (0.2260 in.).



  1. Install the selected valve lifter.


    A072845E03

    New Lifter Thickness mm (in.) 
    No.
    Thickness
    No.
    Thickness
    No.
    Thickness
    06
    5.060 (0.1992)
    30
    5.300 (0.2087)
    54
    5.540 (0.2181)
    08
    5.080 (0.2000)
    32
    5.320 (0.2094)
    56
    5.560 (0.2189)
    10
    5.100 (0.2008)
    34
    5.340 (0.2102)
    58
    5.580 (0.2197)
    12
    5.120 (0.2016)
    36
    5.360 (0.2110)
    60
    5.600 (0.2205)
    14
    5.140 (0.2024)
    38
    5.380 (0.2118)
    62
    5.620 (0.2213)
    16
    5.160 (0.2031)
    40
    5.400 (0.2126)
    64
    5.640 (0.2220)
    18
    5.180 (0.2039)
    42
    5.420 (0.2134)
    66
    5.660 (0.2228)
    20
    5.200 (0.2047)
    44
    5.440 (0.2142)
    68
    5.680 (0.2236)
    22
    5.220 (0.2055)
    46
    5.460 (0.2150)
    70
    5.700 (0.2244)
    24
    5.240 (0.2063)
    48
    5.480 (0.2157)
    72
    5.720 (0.2252)
    26
    5.260 (0.2071)
    50
    5.500 (0.2165)
    74
    5.740 (0.2260)
    28
    5.280 (0.2079)
    52
    5.520 (0.2173)


    Exhaust valve clearance (Cold):
    0.35 to 0.45 mm (0.0138 to 0.0177 in.)

    EXAMPLE:
    The 5.340 mm (0.2102 in.) lifter is installed, and the measured clearance is 0.480 mm (0.0189 in.). Replace the 5.340 mm (0.2102 in.) shim with a new No.42 lifter.


    A072846E02

    New Lifter Thickness mm (in.) 
    No.
    Thickness
    No.
    Thickness
    No.
    Thickness
    06
    5.060 (0.1992)
    30
    5.300 (0.2087)
    54
    5.540 (0.2181)
    08
    5.080 (0.2000)
    32
    5.320 (0.2094)
    56
    5.560 (0.2189)
    10
    5.100 (0.2008)
    34
    5.340 (0.2102)
    58
    5.580 (0.2197)
    12
    5.120 (0.2016)
    36
    5.360 (0.2110)
    60
    5.600 (0.2205)
    14
    5.140 (0.2024)
    38
    5.380 (0.2118)
    62
    5.620 (0.2213)
    16
    5.160 (0.2031)
    40
    5.400 (0.2126)
    64
    5.640 (0.2220)
    18
    5.180 (0.2039)
    42
    5.420 (0.2134)
    66
    5.660 (0.2228)
    20
    5.200 (0.2047)
    44
    5.440 (0.2142)
    68
    5.680 (0.2236)
    22
    5.220 (0.2055)
    46
    5.460 (0.2150)
    70
    5.700 (0.2244)
    24
    5.240 (0.2063)
    48
    5.480 (0.2157)
    72
    5.720 (0.2252)
    26
    5.260 (0.2071)
    50
    5.500 (0.2165)
    74
    5.740 (0.2260)
    28
    5.280 (0.2079)
    52
    5.520 (0.2173)


    Intake valve clearance (Cold):
    0.20 to 0.30 mm (0.0079 to 0.0118 in.)

    EXAMPLE:
    The 5.250 mm (0.2067 in.) lifter is installed, and the measured clearance is 0.400 mm (0.0158 in.). Replace the 5.250 mm (0.2067 in.) shim with a new No.40 lifter.



18. INSTALL CAMSHAFT


    A070551
  1. Set the crankshaft to 90° position from the TDC/compression.



    A074299E01
  1. Place the camshaft to the cylinder head as shown in the illustration.

    NOTICE:
    Apply engine oil to the cams, thrusts and gears of the camshaft as well as on the journal of the cylinder head.



    A070701E01
  1. Align the dot marks of the camshaft and No.2 camshaft by meshing the both gears before placing the No.2 camshaft.

  1. Remove old packing (FIPG) from the camshaft bearing cap.



    A115157E01
  1. Apply seal packing to the specific places shown in the illustration.

    Seal packing:
    Part No.08826-00080 or equivalent

    Thickness:
    1 mm (0.04 in.)

    NOTICE:
    1. Be careful not to adhere FIPG to the oil passage of the bearing cap.
    2. After applying FIPG, install the camshaft bearing cap within 3 minutes and then tighten its bolts within 15 minutes.
    3. Do not start the engine 2 hours after the installation.



    A070704
  1. Install the camshaft bearing cap as shown in the illustration.

  1. Tighten the 15 bolts for the camshaft bearing cap in the specified order shown in the illustration.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Adjust and inspect valve clearance.

    1. Fix the timing belt cover No.2 with the 4 bolts and nuts.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    2. Tighten the bolt for the camshaft timing pulley while holding the camshaft with a monkey wrench.

      Torque:
      98 N*m{ 1,000 kgf*cm , 72 ft.*lbf }

    3. Adjust and inspect the valve clearance. (Click here)

    4. Remove the camshaft timing pulley and timing belt cover No.2.



19. INSTALL CAMSHAFT SETTING OIL SEAL
  1. Apply a bit of MP grease to a new oil seal's lip.

    NOTICE:
    Keep the lip clean. Do not to bring dirt and dust on that area.



    A074375E01
  1. Using SST and a hammer, fit the oil seal.

    SST
    09608-06041  

    Oil seal depth from flat end face:
    0.5 to 1.5 mm (0.020 to 0.060 in.)

    NOTICE:
    Install the oil seal straight.



20. INSTALL INJECTOR ASSEMBLY
(Click here)


21. CHECK NOZLLE LEAKAGE PIPE LEAK



22. INSTALL TIMING BELT NO.2 COVER


    A069864E02
  1. Remove old seal packing (FIPG) from the timing gear case.

  1. Apply seal packing to the specific places shown in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    NOTICE:
    1. After applying FIPG, install the timing belt No.2 cover within 3 minutes and tighten its bolts and nuts within 15 minutes.
    2. Do not start the engine 2 hours after the installation.

  1. Fix the timing belt cover No.2 with the 4 bolts and nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



23. INSTALL TIMING BELT IDLER SUB-ASSEMBLY NO.1


    A070696
  1. Using a 10 mm socket hexagon wrench, install the new plate washer and timing belt idler No.1.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



24. INSTALL CAMSHAFT TIMING PULLEY


    A070695
  1. Install the camshaft timing pulley.

  1. Tighten the bolt for the camshaft timing pulley while holding the camshaft with a monkey wrench.

    Torque:
    98 N*m{ 1,000 kgf*cm , 72 ft.*lbf }



25. PISTON AND VALVE BREAKE PREVENT WORK


    A070551
  1. When turning the camshaft with the timing belt removed, turn the crankshaft 90° counterclockwise.

    NOTICE:
    When installing the timing belt, it is necessary to return the camshaft to the timing marks and then turn the crankshaft clockwise so that it aligns with the timing marks as shown in the illustration.



26. INSTALL TIMING BELT


    A070691E01
  1. Check that the timing marks are aligned as shown in the illustration.

  1. Install the timing belt to pump drive shaft pulley, camshaft timing pulley and timing belt idler No.1 in sequence.



    A070548
  1. Set the tensioner to the press upright.

    NOTICE:
    1. Do not allow the rod end to scratch and deform.
    2. Press the tensioner rod in upward.
    3. Protect a tip of the push rod with a rag in order to prevent damage.

  1. Using a press, slowly apply 981 to 9,807 N (100 to 1,000 kgf, 220 to 2,205 lbf) of force to the push rod.

    NOTICE:
    Do not apply loads 981 to 9,807 N (100 to 1,000 kgf, 220 to 2,205 lbf) or more on the push rod.

  1. Align the holes of push rod and housing, pass a 1.27 mm hexagon wrench through the holes to keep the setting position of the push rod.

  1. Temporarily install the timing belt tensioner with the 2 bolts while pushing the idler pulley toward the timing belt.

  1. Tighten the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Uniformly tighten the 2 bolts and install the tensioner

  1. Remove the 1.5 mm hexagon wrench from the tensioner.



    A070549E01
  1. Turn the crankshaft in the clockwise direction twice, check that the timing marks are aligned as shown in the illustration.



27. INSTALL TIMING BELT NO.1 COVER


    A102815
  1. Install the timing belt No.1 cover with the 6 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Install the wire harness clamp.



28. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove old seal packing (FIPG) from the cylinder head.



    A070541E01
  1. Apply a seal packing to the specific places described in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    NOTICE:
    1. After applying the seal packing, parts must be assembled within 3 minutes, and then tighten within 15 minutes.
    2. Otherwise the material must be removed and reapplied.
    3. Do not start the engine 2 hour after the installation.

  1. Install the cylinder head cover with 10 bolts and 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the ventilation hose.

  1. Install a new nozzle holder seal.



29. INSTALL INJECTION PIPE
(Click here)


30. INSTALL DIESEL THROTTLE BODY ASSEMBLY
(Click here)


31. INSTALL FAN AND GENERATOR V BELT


    A102808E03
  1. Install the drive belt by rotating the tensioner pulley in clockwise direction with the pulley set bolt of the tensioner.

    NOTICE:
    Make sure that the V belt is set properly at each pulley.



    A080039E01
  1. Make sure that the indicator mark of the tensioner is within range A.



32. CONNECT BATTERY NEGATIVE TERMINAL


33. ADD ENGINE COOLANT
  1. Firmly tighten the drain plugs and fill the radiator reserve tank assembly with coolant to the top of the inlet.

  1. Loosen the bleeder plug of outlet housing.

  1. When air is bled and the coolant drains out, firmly install the bleeder plug.

  1. Add coolant up to the B line mark in the radiator reserve tank assembly and install the radiator cap.

    Coolant capacity:
    Condition
    Capacity
    w/ rear heater
    17.0 liters (18.0 US qts, 15.0 imp. qts)
    w/o rear heater
    15.0 liters (15.9 US qts, 13.2 imp. qts)

  1. Warm up the engine.

  1. After the engine cools down check that the coolant level is between the LOW and FULL level marks.



34. BLEED FUEL LINE
  1. Move the priming pump in the upper part of the fuel filter assembly up and down, and fill the injection pump assembly and fuel system with fuel.



35. CHECK FUEL LEAK
  1. PERFORM ACTIVE TEST

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / ECD / Active Test.

    5. Perform the Active Test.

      Intelligent Tester Display
      Test Details
      Control Range
      Diagnostic Notes
      Test the Fuel Leak
      Pressurizes common rail internal fuel pressure, and checks for fuel leaks
      Stop/Start
      1. Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when ON is selected
      2. Above conditions preserved while test is ON



36. CHECK FOR ENGINE OIL LEAKS


37. CHECK FOR ENGINE COOLANT LEAKS

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester to the radiator.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 137 kPa (1.4 kgf/cm2, 19.9 psi), and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator or water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



38. INSTALL ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1)

Torque:
13 N*m{ 133 kgf*cm , 10 ft.*lbf }



39. CHECK IDLE SPEED

NOTICE:
This checking procedure should be done under the following condition.

HINT:
  1. Regarding the details about the intelligent tester, refer to its operator's manual.
  2. If the intelligent tester is not available, a tachometer's tester probe can substitute for it.

  1. Connect the intelligent tester to the DLC3.



    A059802E01
  1. If the tester is not available, connect a tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.

    SST
    09843-18030  

  1. Start the engine and check the idle speed.

    Idle speed:
    700 to 800 rpm

    HINT:
    If the idle speed is not as specified, check by troubleshooting in the diagnostics section.

  1. In case of the tester probe of the tachometer is connected to the DLC3, disconnect the tester probe from terminal 9 of the DLC3 with SST.

  1. Disconnect the intelligent tester from the DLC3.



40. INSPECT MAXIMUM ENGINE SPEED

NOTICE:
This checking procedure should be done under the following condition.

HINT:
  1. Regarding the details about the intelligent tester, refer to its operator's manual.
  2. If the intelligent tester is not available, a tachometer's tester probe can substitute for it.

  1. Connect the intelligent tester to the DLC3.



    A059802E01
  1. If the tester is not available, connect a tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.

    SST
    09843-18030  

  1. Start the engine.

  1. Depress the accelerator pedal all the way to the limit.

  1. Check the maximum speed.

    Maximum speed:
    4500 to 4700 rpm

    HINT:
    If the maximum speed is not as specified, check by troubleshooting in the diagnostics section.

  1. In case of the tester probe of the tachometer is connected to the DLC3, disconnect the tester probe from terminal 9 of the DLC3 with SST.

  1. Disconnect the intelligent tester from the DLC3.



41. PERFORM INITIALIZATION
(Click here)