Home › ENGINE ยท 5L-E › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL WIRE HARNESS CLAMP BRACKET
  1. Install the bolt and wire harness clamp bracket.



2. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY


    A113490
  1. Clean the threads of the oil pressure switch, and apply adhesive to them.

    Adhesive:
    Part No.08833-00080 THREE BOND 1344 or equivalent



    A112063
  1. Using a 24 mm deep socket wrench, install the oil pressure switch.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }



3. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY
  1. Install a new gasket and oil filter bracket with the 10 bolts and 2 nuts.

    Torque:
    30 N*m{ 300 kgf*cm , 22 ft.*lbf }



4. INSTALL OIL FILTER SUB-ASSEMBLY
  1. Check and clean the oil filter installation surface.

  1. Apply clean engine oil to the rubber gasket of a new oil filter.

  1. Instal the oil filter, and tighten it by hand until the rubber gasket contacts the installation surface.



    A058655E01
  1. Using SST, tighten it by an additional 3/4 turn to seat the filter.

    SST
    09228-44011  



5. INSTALL EXHAUST MANIFOLD


    A058725E01
  1. Install a new gasket to the cylinder head.

    HINT:
    Be sure to install a new gasket in the correct direction as shown in the illustration.



    A113082
  1. Install the exhaust manifold with the 6 bolts and 2 new nuts. Uniformly tighten the bolts and nuts in several steps.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }



6. INSTALL EXHAUST MANIFOLD HEAT INSULATOR NO.1


    A058726E01
  1. Install the heat insulator with the 3 bolts.

    Torque:
    Bolt (A):
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }
    Bolt (B):
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }



7. INSTALL OIL LEVEL GAGE GUIDE
  1. Install the oil level gage guide to the cylinder head.



8. INSTALL OIL LEVEL GAGE SUB-ASSEMBLY
  1. Install the oil level gage sub-assembly to the cylinder head.



9. INSTALL ENGINE MOUNTING BRACKET FRONT NO.1 RH


    A112058
  1. Install the 6 bolts and engine mounting bracket front No.1 RH.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



10. INSTALL GENERATOR W/ VACUUM PUMP ASSEMBLY


    A113355
  1. Temporarily tighten the bolt and generator w/ vacuum pump assembly.



    A112062
  1. Install the clip with the hose connected.

  1. Install the bolt with the hose connected.

    Torque:
    14 N*m{ 140 kgf*cm , 10 ft.*lbf }



11. INSTALL PUMP BRACKET


    A112057E01
  1. Install the 6 bolts and pump bracket.

    Torque:
    Bolt (A):
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }
    Bolt (B):
    57 N*m{ 581 kgf*cm , 42 ft.*lbf }



12. INSTALL EXHAUST PIPE SUPPORT BRACKET NO.1


    A112059
  1. Install the 2 bolts, exhaust pipe support bracket No.1 and stiffener plate RH.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



13. INSTALL ENGINE OIL LEVEL SENSOR


    A112056
  1. Install the 4 bolts and engine oil level sensor.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



14. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
  1. Clean the threads of the water drain cock, and apply adhesive to them.

    Adhesive:
    Part No.08833-00070 THREE BOND 1324 or equivalent

  1. Install the water drain cock.

    Torque:
    57 N*m{ 581 kgf*cm , 42 ft.*lbf }



15. INSTALL WATER BY-PASS HOSE UNION
  1. Clean the threads of the water by-pass hose union, and apply adhesive to them.

    Adhesive:
    Part No.08833-00070 THREE BOND 1324 or equivalent

  1. Install the water by-pass hose union.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



16. INSTALL INTAKE MANIFOLD


    A058724E01
  1. Install a new gasket to the cylinder head with the protrusion facing upward.



    A113083
  1. Install the intake manifold with the 6 bolts and 2 nuts. Uniformly tighten the bolts and nuts in several steps.

    Torque:
    24 N*m{ 240 kgf*cm , 17 ft.*lbf }



17. INSTALL WATER OUTLET HOUSING


    A113081
  1. Install a new gasket, the water outlet and outlet hosing assembly with the 3 bolts.

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }



18. INSTALL CRANK POSITION SENSOR
  1. Coat a O-ring with engine oil.



    A111054
  1. Install the crank position sensor with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the crank position sensor connector.



19. INSTALL INJECTION OR SUPPLY PUMP ASSEMBLY


    A071318
  1. Install the injection or supply pump assembly to timing gear case, and temporarily tighten the 2 nuts.

  1. Install injection pump stay No.1 to the injection or supply pump assembly rear end, and temporarily tighten the 3 bolts.



    A071319
  1. Rotate the pump body to make the marking of pump flange conform to the making of timing of gear case.

  1. Tighten the 2 nuts to install the injection or supply pump assembly.

    Torque:
    21 N*m{ 210 kgf*cm , 15 ft.*lbf }

  1. Tighten the 3 bolts to install the injection pump stay No.1.

    Torque:
    Injection pump stay No.1 x Cylinder Block:
    21 N*m{ 210 kgf*cm , 15 ft.*lbf }
    Injection pump stay No.1 x Injection Pump:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }

  1. Connect the 3 fuel hoses.

  1. Connect the engine speed sensor connector.

  1. Connect the spill control valve connector.

  1. Connect the correction unit connector.

  1. Connect the timer control valve connector.

  1. Connect the fuel temperature sensor connector.

  1. Connect the engine wire clamp.



20. INSTALL INJECTION PUMP DRIVE PULLEY


    A071313E01
  1. Using SST, install the injection pump drive pulley with the nut.

    SST
    09213-14010   (91651-60865)
    09330-00021  

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }



21. INSTALL GLOW PLUG ASSEMBLY
  1. Using a 12 mm deep socket wrench, install the 4 glow plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 10 ft.*lbf }



22. INSTALL NOZZLE HOLDER AND NOZZLE SET
  1. Place 4 new injection nozzle seat gaskets and 4 injection nozzle seats into the injection nozzle holes of the cylinder head.

  1. Using SST, install the 4 nozzle holder and nozzle sets.

    SST
    09268-64010   (09268-64020)

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }



23. INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY
  1. Install 4 new ring packing washers and the leakage pipe assembly with the 4 nuts.

    Torque:
    30 N*m{ 300 kgf*cm , 22 ft.*lbf }

  1. Connect the fuel hose to the leakage pipe.



24. INSTALL GLOW PLUG NO.1 CONNECTOR

Torque:
1.0 N*m{ 10 kgf*cm , 9 in.*lbf }



25. INSTALL INJECTION PIPE SET
  1. Connect the 2 lower clamps on the intake manifold.

  1. Install the 4 injection pipes.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. Secure the injection pipes with the 2 upper pipe clamps and 2 nuts.

    Torque:
    5.0 N*m{ 50 kgf*cm , 44 in.*lbf }



26. INSTALL VENTURI ASSEMBLY
  1. Install a new gasket and venturi.



    A111053E01
  1. Connect the throttle control motor connector.



    A111052E01
  1. Connect the throttle open switch connector.



27. INSTALL INTAKE AIR CONNECTOR BRACKET


    A112061
  1. Install the 2 bolts and intake air connector bracket.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



28. INSTALL INTAKE AIR CONNECTOR SUB-ASSEMBLY


    A111051
  1. Install a new gasket and intake air connector with the bolt and 3 nuts.

    Torque:
    bolt:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }
    Nut:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Connect the turbo pressure sensor connector.

  1. Connect the ventilation hose.



29. INSTALL TIMING BELT
(Click here)


30. INSTALL COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning)
  1. Temporarily install the compressor mounting bracket with the 4 bolts.



    A112015E01
  1. Using several steps, uniformly install and tighten the 4 bolts in the sequence shown in the illustration.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }



    A112016
  1. Temporarily tighten the bolt and spacer.



    A112014E01
  1. Temporarily install the compressor mounting bracket with the 3 bolts.

  1. Using several steps, uniformly install and tighten the 3 bolts in the sequence shown in the illustration.

    Torque:
    47 N*m{ 475 kgf*cm , 36 ft.*lbf }



31. INSTALL FAN BELT ADJUSTING BAR (w/o Air Conditioning)


    A113094
  1. Install the 2 bolts and fan belt adjusting bar.

    Torque:
    45 N*m{ 460 kgf*cm , 33 ft.*lbf }



    A113369
  1. Temporarily install the bolt.



32. CONNECT ENGINE MOUNTING INSULATOR FRONT
  1. Connect the engine mounting insulator front with the 4 bolts.

    Torque:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }



33. CONNECT VANE PUMP ASSEMBLY
  1. Temporarily install the vane pump assembly with the 2 bolts.



    A071326E01
  1. Install the pulley to the pump shaft.

  1. Using SST, stop the pulley rotation and torque the nut.

    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    43 N*m{ 440 kgf*cm , 32 ft.*lbf }



34. INSTALL ENGINE WIRE


35. INSTALL REAR END PLATE
  1. Install the 2 bolts and rear end plate.

    Torque:
    27 N*m{ 275 kgf*cm , 19 ft.*lbf }



36. INSTALL FLYWHEEL SUB-ASSEMBLY


    A058716E01
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. Clean the bolts and bolt holes.

  1. Apply adhesive to 2 or 3 threads of the bolts.

    Adhesive:
    Part No.08833-00070, THREE BOND 1324 or equivalent

  1. Install the flywheel on the crankshaft.



    A058717E01
  1. Install and uniformly tighten the 8 bolts in several steps, in the sequence shown.

    Torque:
    123 N*m{ 1,250 kgf*cm , 90 ft.*lbf }

    NOTICE:
    Do not start the engine within an hour after installing.



37. INSTALL CLUTCH DISC ASSEMBLY


    C104158E01
  1. Insert SST into the clutch disc assembly, then insert them into the flywheel sub-assembly.

    SST
    09301-00110  

    NOTICE:
    Take care not to insert the clutch disc assembly in the wrong direction.



38. INSTALL CLUTCH COVER ASSEMBLY


    C114265E02
  1. Align the matchmarks on the clutch cover assembly with the one on the flywheel sub-assembly.

  1. Following the procedures shown in the illustration, tighten the 6 bolts starting from the bolt located near the knock pin on the top.

    SST
    09301-00110  

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

    HINT:
    1. Evenly tighten the bolts by following the order shown in the illustration.
    2. Tighten the bolts after checking that the disc is in the center by lightly moving the SST up and down, left and right.



39. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY


    C086210
  1. Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

    Maximum non-alignment:
    0.9 mm (0.035 in.)



    C114266E01
  1. If alignment is not as specified, adjust the diaphragm spring tip alignment using SST.

    SST
    09333-00013  



40. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY



41. INSTALL STARTER ASSEMBLY (for 2.2kW Type)
  1. Install the starter with the 2 bolts and nut.

    Torque:
    69 N*m{ 700 kgf*cm , 51 ft.*lbf }

  1. Install the stay with the 2 bolts and nut.

    Torque:
    69 N*m{ 104 kgf*cm , 51 ft.*lbf }

  1. Connect the 30 terminal with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Install the terminal cap.

  1. Connect the starter connector.



42. INSTALL STARTER ASSEMBLY (for 2.7kW Type)
  1. Install the starter with the 2 bolts, nut and stay.

    Torque:
    69 N*m{ 700 kgf*cm , 51 ft.*lbf }

  1. Install the starter stay with the 2 bolts and nut.

    Torque:
    Bolt:
    37 N*m{ 380 kgf*cm , 27 ft.*lbf }
    Nut:
    12.5 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Connect the 30 terminal with the nut.

    Torque:
    21 N*m{ 215 kgf*cm , 16 ft.*lbf }

  1. Install the terminal cap.

  1. Connect the starter connector.



43. INSTALL ENGINE W/ TRANSMISSION ASSEMBLY
  1. Using the engine lifter, install the engine w/ transmission assembly to the vehicle.



    A101144E03
  1. Install the 4 bolts and stabilizer bracket.

    Torque:
    Bolt (A):
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Install the 16 bolts and front suspension cross member.

    Torque:
    Bolt (B):
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Bolt (C):
    150 N*m{ 1,530 kgf*cm , 111 ft.*lbf }

  1. Connect the rear engine mounting.

    Torque:
    98 N*m{ 1,000 kgf*cm , 72 ft.*lbf }

    NOTICE:
    Tighten the nuts when install the engine mounting.

  1. Remove the engine lifter.



44. CONNECT STEERING TORQUE SHAFT ASSEMBLY


    C106143E01
  1. Align the matchmarks on the steering torque shaft assembly and the power steering link assembly.



    C106142E01
  1. Install bolt (B) and tighten the 2 bolts.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



45. CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY


    C102209
  1. Install the clutch release cylinder with the 2 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }



46. CONNECT WIRE HARNESS


    C112944
  1. Connect the 2 connectors and clamp.



47. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C102659E01
  1. Install 2 new clips to the transmission control cable bracket No.1.

  1. Install the transmission control cable assembly to the transmission control cable bracket No.1.

    NOTICE:
    1. Be sure that A claws of the clips are firmly engaged into the bracket grooves.
    2. Be sure the cable is set in the clip with both B claws erected to prevent slippage of the cable in the opposite direction.



    C102206E01
  1. Align the matchmarks on the control cable assembly and the outer lever.

  1. Install the transmission control cable assembly to the outer levers with the 2 nuts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



48. CONNECT SHOCK ABSORBER ASSEMBLY FRONT LH
(Click here)


49. CONNECT SHOCK ABSORBER ASSEMBLY FRONT RH

HINT:
Use the same procedures described for the LH side.



50. CONNECT FRONT SUSPENSION ARM SUB-ASSEMBLY UPPER LH


    C102007E02
  1. Connect the front suspension upper arm to the steering knuckle with the nut.

    Torque:
    113 N*m{ 1,150 kgf*cm , 83 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    1. If the holes for the cotter pin are not aligned, tighten the nut up to 60°.
    2. Do not damage the ball joint dust cover.



51. CONNECT FRONT SUSPENSION ARM SUB-ASSEMBLY UPPER RH

HINT:
Use the same procedures described for the LH side.



52. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH


    C102283E01
  1. Install the brake caliper assembly to the steering knuckle with the 2 bolts.

    Torque:
    123 N*m{ 1,250 kgf*cm , 91 ft.*lbf }



53. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



54. INSTALL SPEED SENSOR FRONT LH (w/ ABS)


    C102281E01
  1. Install the speed sensor to the steering knuckle with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.
    3. Do not twist the sensor wire when installing the speed sensor.



55. INSTALL SPEED SENSOR FRONT RH (w/ ABS)

HINT:
Use the same procedures described for the LH side.



56. INSTALL PROPELLER SHAFT ASSEMBLY (for Long Wheelbase)


    C102186E01
  1. Remove the SST from the extension housing.

  1. Install the propeller shaft assembly in the extension housing.

  1. Align the matchmarks on the propeller shaft flange and differential flange.



    C102185E01
  1. Install the propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.

    Torque:
    74 N*m{ 755 kgf*cm , 54 ft.*lbf }



57. INSTALL PROPELLER SHAFT ASSEMBLY (for Super Long Wheelbase)


    C102186E01
  1. Remove the SST from the extension housing.

  1. Install the propeller with center bearing shaft assembly in the extension housing.



    C107214
  1. Install the center support bearing assembly No.1, and temporarily tighten the 2 bolts.



    C102185E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assy with the 4 nuts, 4 bolts and 4 washers.

    Torque:
    74 N*m{ 755 kgf*cm , 54 ft.*lbf }



    C107213E01
  1. Check that the center line of the bracket is at right angles to the shaft axial direction.



    C115777E01
  1. Adjust the center support bearing assembly No.1.

    HINT:
    1. With the vehicle unladen, adjust the center support bearing No.1 to maintain the angles, as shown.
    2. In the same conditions, check the center line in the axial direction. Adjust the bearing if necessary.
    3. The center bearing center line and center bearing housing center line must be adjusted to within -1.0 to 1.0 mm (-0.0394 to 0.0394 in.) of each other in the vehicle's longitudinal direction with the vehicle unladen.

  1. Tighten the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }



58. INSTALL EXHAUST PIPE SUB-ASSEMBLY FRONT NO.1 (for Long Wheelbase)
  1. Install a new gasket and exhaust pipe sub-assembly front No.1 with the 3 bolts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }

  1. Tighten the clamp bolt, and install the exhaust pipe support bracket No.1 to the exhaust pipe sub-assembly front No.1.



59. INSTALL EXHAUST PIPE SUB-ASSEMBLY FRONT NO.1 (for Super Long Wheelbase)
  1. Install a new gasket and exhaust pipe sub-assembly front No.1 with the 3 bolts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }

  1. Tighten the clamp bolt, install the exhaust pipe support bracket No.1 to the exhaust pipe sub-assembly front No.1.



60. INSTALL EXHAUST PIPE SUB-ASSEMBLY FRONT NO.2 (for Long Wheelbase)


    A077857
  1. Inspect the compression spring.

    1. Using vernier calipers, measure the free length of the compression springs.

      Minimum length:
      40.5 mm (1.594 in.)

      HINT:
      If the free length is less than the minimum, replace the compression spring.



    A102062E05
  1. Install the gasket.

    1. Fully insert a new gasket to the exhaust pipe sub-assembly front No.1 by hand.

    2. Using a wooden block, uniformly strike the gasket so that the gasket and exhaust pipe sub-assembly front No.1 are properly fit.

      NOTICE:
      1. Be careful with the installation direction of the gasket.
      2. Do not damage the outer face.
      3. Do not reuse the gasket.
      4. To ensure a proper seal, do not use the exhaust pipe sub-assembly front No.2 to force the gasket onto the front exhaust pipe sub-assembly front No.1.

  1. Connect the exhaust pipe support, and install a new gasket and the exhaust pipe sub-assembly front No.2 with the 4 bolts, 2 nuts, and 2 compression springs.

    Torque:
    Exhaust pipe sub-assembly front No.1 side:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }
    Exhaust pipe assembly tail side:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    After installation, check that the clearance is almost same at any point between the flanges of the exhaust pipe sub-assembly front No.2 and exhaust pipe sub-assembly front No.1.



61. INSTALL EXHAUST PIPE SUB-ASSEMBLY FRONT NO.2 (for Super Long Wheelbase)


    A077857
  1. Inspect the compression spring.

    1. Using vernier calipers, measure the free length of the compression springs.

      Minimum length:
      40.5 mm (1.594 in.)

      HINT:
      If the free length is less than the minimum, replace the compression spring.



    A102062E05
  1. Install the gasket.

    1. Fully insert a new gasket to the exhaust pipe sub-assembly front No.1 by hand.

    2. Using a wooden block, uniformly strike the gasket so that the gasket and exhaust pipe sub-assembly front No.1 are properly fit.

      NOTICE:
      1. Be careful with the installation direction of the gasket.
      2. Do not damage the gasket.
      3. Do not reuse the gasket.
      4. To ensure a proper seal, do not use the exhaust pipe sub-assembly front No.2 to force the gasket onto the exhaust pipe sub-assembly front No.1.

  1. Connect the exhaust pipe support, and install a new gasket and the exhaust pipe sub-assembly front No.2 with the 4 bolts, 2 nuts, and 2 compression springs.

    Torque:
    Exhaust pipe sub-assembly front No.1 side:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }
    Exhaust pipe assembly center side:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    After installation, check that the clearance is almost same at any point between the flanges of the exhaust pipe sub-assembly front No.2 and exhaust pipe sub-assembly front No.1 .



62. CONNECT ENGINE WIRE


    A101143E02
  1. Install the connector and nut, as shown the illustration.

  1. Install the nut then remove the starter wire harness.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the clamp and ground cable of the engine wire.

  1. Connect the connectors to the ECM.

  1. Install the wire harness support to the ECM.



63. CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY


    C101999E01
  1. Install the vane pump oil reservoir assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



64. INSTALL COMPRESSOR AND MAGNETIC CLUTCH
(Click here)


65. CONNECT AIR CLEANER HOSE NO.2
  1. Install the air cleaner hose No.2 with the clamp.



66. CONNECT INJECTION PUMP TO FUEL FILTER FUEL HOSE OR PIPE


67. CONNECT RADIATOR HOSE NO.4


68. CONNECT RADIATOR HOSE INLET


69. INSTALL FAN AND GENERATOR V BELT (w/o Air Conditioning)


    A115631E01
  1. Install the V belt.

  1. Using a bar, adjust the tension of the V belt.

  1. Tighten the bolts A and B.

    Torque:
    Bolt A:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }
    Bolt B:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }

  1. Check the tension of the V belt. (Click here)



70. INSTALL FAN AND GENERATOR V BELT (w/ Air Conditioning)


    A115632E01
  1. Install the V belt.

  1. Tightening the bolt C, adjust the tension of the V belt.

  1. Tighten the bolts A and B.

    Torque:
    Bolt A:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }
    Bolt B:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }

  1. Check the tension of the V belt. (Click here)



71. INSTALL V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1


    A074095E01
  1. Install the V belt.

  1. Tightening the bolt B, adjust the tension of the V belt.

  1. Tighten nut A.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

  1. Check the tension of the V belt. (Click here)



72. INSTALL VANE PUMP V BELT


    A071310E01
  1. Install the V belt.

  1. Using a bar, adjust the tension of the V-ribbed belt.

  1. Tighten the bolt A and nut B.

    Torque:
    Bolt (A):
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }
    Nut (B):
    64 N*m{ 635 kgf*cm , 47 ft.*lbf }

  1. Check the tension of the V belt. (Click here)



73. INSTALL ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Install the 5 bolts and engine service hole cover.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



74. INSTALL FRONT DOOR SCUFF PLATE RH


75. INSTALL FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)
Use the same procedures described for the LH side. See page


76. INSTALL FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)
Use the same procedures described for the LH side.


77. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


78. INSTALL FRONT WHEEL


79. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


80. ADD ENGINE OIL


81. ADD ENGINE COOLANT
  1. Close the engine drain plug.

    Torque:
    57 N*m{ 581 kgf*cm , 42 ft.*lbf }

  1. Close the radiator drain cock plug.

  1. Slowly fill the cooling system with coolant.

    HINT:
    The coolant level inside the radiator should be abserved after pressing the radiator hose inlet and radiator hose outlet by hand..

  1. Slowly pour coolant into the radiator reserve tank until it reaches the FULL line.

  1. Install the radiator cap to the radiator reserve tank.

  1. Press the inlet and outlet radiator hoses several times by hand while warming up the engine.

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add coolant to the FULL line of the radiator reservoir.



82. BLEED AIR FROM FUEL SYSTEM


    A114068E01
  1. Using the hand pump, bleed air from the fuel system until pumping becomes difficult.



83. CHECK FUEL LEAK
  1. Check that there are no fuel leaks anywhere on the fuel system after doing maintenance.

    HINT:
    When checking for fuel leaks, make sure that there is pressure in the fuel line.



84. CHECK FOR ENGINE OIL LEAKS


85. CHECK FOR ENGINE COOLANT LEAKS

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester to the radiator.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator or water pump for leaks. If no external leaks are found, check the heater core, cylinder block, and cylinder head.



86. INSPECT CHECK TRANSMISSION OIL


    D025304E01
  1. Park the vehicle in a level place.

  1. Remove the transmission filler plug and gasket.

  1. Check that the oil surface is within 5 mm (0.20 in.) below the lowest point of the transmission filler plug opening.

    Oil grade:
    GL-4 or GL-5
    Viscosity:
    SAE 75W-90
    Capacity:
    2.2 liters (2.3 US qts, 1.9 lmp. qts)

    NOTICE:
    1. Problems may occur when the oil level is too high or too low.
    2. After replacing the oil, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install the transmission filler plug and a new gasket.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



87. CHECK FOR EXHAUST GAS LEAKS


88. ADJUST FRONT WHEEL ALIGNMENT
(Click here)


89. CHECK IDLE SPEED
  1. Warm up the engine.

  1. When using an intelligent tester:

    1. Connect the intelligent tester to the DLC3.

      Idle speed:
      720 to 820 rpm (A/C OFF)
      750 to 850 rpm (A/C ON)

      HINT:
      Refer to the intelligent tester operator's manual for further details.



    A052006E02
  1. When not using an intelligent tester:

    1. Using SST, connect the tachometer test probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18040  

    2. Check the idle speed.

      Idle speed:
      720 to 820 rpm (A/C OFF)
      750 to 850 rpm (A/C ON)

      NOTICE:
      Switch off all accessories.



90. INSPECT MAXIMUM ENGINE SPEED
  1. Start the engine.

  1. Depress the accelerator pedal all the way.

  1. Check the maximum speed.

    Maximum speed:
    4,850 to 4,950 rpm



91. CHECK ABS SENSOR SIGNAL
(Click here)


92. PERFORM INITIALIZATION
(Click here)