2014-2019 Hiace · Service Manual BRAKE

C1407 Open or Short in Rear Speed Sensor RH Circuit

Diagnostic trouble codes · Vehicles built from Dec 2017

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

Refer to DTCs C1403 and C1404 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
C1407
C1408
Either of the following is detected:
  1. An open in the speed sensor signal circuit continues for 0.5 seconds or more.
  2. With the +BS terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.
  1. Rear speed sensor RH/LH
  2. Wire harness or connector
  3. Skid control ECU (Brake actuator assembly)

HINT:
  1. DTC C1407 is for the rear speed sensor RH.
  2. DTC C1408 is for the rear speed sensor LH.


WIRING DIAGRAM

Refer to DTCs C1403 and C1404 (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Speed Open
    Rear speed sensor RH open detection / Error or Normal
    Normal
    Error: Momentary interruption
    RL Speed Open
    Rear speed sensor LH open detection / Error or Normal
    Normal
    Error: Momentary interruption

    OK:
    Normal (There are no momentary interruptions.)

    HINT:
    Perform the above inspection before removing the sensor and connector.


    Result:
    Result
    Proceed to
    OK
    A
    NG (for LH)
    B
    NG (for RH)
    C



B
Go to step 4

C
Go to step 5
A


2. READ VALUE USING GTS (REAR SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    RL Wheel Speed
    Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


    Result:
    Result
    Proceed to
    OK
    A
    NG (for LH)
    B
    NG (for RH)
    C

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
Go to step 4

C
Go to step 5
A


3. RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Perform a road test.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTCs C1407 and C1408 are not output
    A
    DTCs C1407 and/or C1408 are output
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

4. INSPECT REAR SPEED SENSOR RH

  1. C319887E01
    Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the A and P1 rear speed sensor RH connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 - P1-1 (RL-)
    Always
    Below 1 Ω
    A-3 or P1-1 (RL-) - Body ground
    Always
    10 kΩ or higher
    A-1 - P1-2 (RL+)
    Always
    Below 1 Ω
    A-1 or P1-2 (RL+) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Rear Speed Sensor RH
    *a
    Front view of wire harness connector
    (to Sensor Side Connector)
    *b
    Front view of wire harness connector
    (to Vehicle Side Connector)

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE REAR SPEED SENSOR RH (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    B92-15 (RR-) - P1-3 (RR-)
    Always
    Below 1 Ω
    B92-15 (RR-) or P1-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    B92-16 (RR+) - P1-4 (RR+)
    Always
    Below 1 Ω
    B92-16 (RR+) or P1-4 (RR+) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    B92-28 (RL-) - P1-1 (RL-)
    Always
    Below 1 Ω
    B92-28 (RL-) or P1-1 (RL-) - Body ground
    Always
    10 kΩ or higher
    B92-29 (RL+) - P1-2 (RL+)
    Always
    Below 1 Ω
    B92-29 (RL+) or P1-2 (RL+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

  1. C321142E01
    Reconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    P1-4 (RR+) - Body ground
    Ignition switch ON
    8 to 14 V
    for LH:
    Tester Connection
    Condition
    Specified Condition
    P1-2 (RL+) - Body ground
    Ignition switch ON
    8 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Speed Sensor RH)

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK

REPLACE REAR SPEED SENSOR (Click here)


← C1407 Open or Short in Rear Speed Sensor RH Circuit (+ C1408) (Jan 2017 – Nov 2017)C1413 Front Speed Sensor RH Output Malfunction (+ C1414) (Jan 2015 – Mar 2016) →