C1407 Open or Short in Rear Speed Sensor RH Circuit
Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016
Also covers:
- C1408 Open or Short in Rear Speed Sensor LH Circuit
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
Refer to DTCs C1403 and C1404 (Click here).| DTC No. |
DTC Detection Condition |
Trouble Area |
| C1407 C1408 |
Either of the following is detected:
|
|
- HINT:
- DTC C1407 is for the rear speed sensor RH.
- DTC C1408 is for the rear speed sensor LH.
- DTC C1407 is for the rear speed sensor RH.
WIRING DIAGRAM
Refer to DTCs C1403 and C1404 (Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).
| 1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Speed Open
Rear speed sensor RH open detection / Error or Normal
Normal
Error: Momentary interruption
RL Speed Open
Rear speed sensor LH open detection / Error or Normal
Normal
Error: Momentary interruption
- OK:
- Normal (There are no momentary interruptions.)
- HINT:
- Perform the above inspection before removing the sensor and connector.
- Result:
Result
Proceed to
OK
A
NG (for LH)
B
NG (for RH)
C
|
|
||||
|
|
||||
| A | |
| 2. READ VALUE USING GTS (REAR SPEED SENSOR) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Wheel Speed
Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
RL Wheel Speed
Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
- Result:
Result
Proceed to
OK
A
NG (for LH)
B
NG (for RH)
C
- HINT:
- If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
|
|
||||
| A | |
| 3. RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Perform a road test.
Check if the same DTC is recorded (Click here).
- Result:
Result
Proceed to
DTCs C1407 and C1408 are not output
A
DTCs C1407 and/or C1408 are output
B
|
|
||||
| A | ||
| ||
| 4. INSPECT REAR SPEED SENSOR RH |
Turn the ignition switch off.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A and P1 rear speed sensor RH connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A-3 - P1-1 (RL-)
Always
Below 1 Ω
A-3 or P1-1 (RL-) - Body ground
Always
10 kΩ or higher
A-1 - P1-2 (RL+)
Always
Below 1 Ω
A-1 or P1-2 (RL+) - Body ground
Always
10 kΩ or higher
Text in Illustration *1
Rear Speed Sensor RH
*a
Front view of wire harness connector
(to Sensor Side Connector)
*b
Front view of wire harness connector
(to Vehicle Side Connector)
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the B92 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for RH:
Tester Connection
Condition
Specified Condition
B92-15 (RR-) - P1-3 (RR-)
Always
Below 1 Ω
B92-15 (RR-) or P1-3 (RR-) - Body ground
Always
10 kΩ or higher
B92-16 (RR+) - P1-4 (RR+)
Always
Below 1 Ω
B92-16 (RR+) or P1-4 (RR+) - Body ground
Always
10 kΩ or higher
- for LH:
Tester Connection
Condition
Specified Condition
B92-28 (RL-) - P1-1 (RL-)
Always
Below 1 Ω
B92-28 (RL-) or P1-1 (RL-) - Body ground
Always
10 kΩ or higher
B92-29 (RL+) - P1-2 (RL+)
Always
Below 1 Ω
B92-29 (RL+) or P1-2 (RL+) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT) |
Reconnect the B92 skid control ECU (brake actuator assembly) connector.

Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
- for RH:
Tester Connection
Condition
Specified Condition
P1-4 (RR+) - Body ground
Ignition switch ON
8 to 14 V
- for LH:
Tester Connection
Condition
Specified Condition
P1-2 (RL+) - Body ground
Ignition switch ON
8 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Rear Speed Sensor RH)
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | ||
| ||
