2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Dec 2017

Versions by build date: Oct 2014 – Nov 2017 from Dec 2017

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.


1. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH
  1. Install the front No. 1 engine mounting bracket with the 4 bolts.

    Torque:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }


2. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH
  1. Install the front No. 1 engine mounting bracket with the 4 bolts.

    Torque:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }


3. INSTALL OIL COOLER COVER SUB-ASSEMBLY
(Click here)

4. INSTALL NO. 2 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
  1. Install the No. 2 vacuum transmitting pipe with the bolt and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


5. INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
  1. Install the No. 1 vacuum transmitting pipe with the bolt and nut.

    Torque:
    for bolt:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }
    for nut:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the vacuum hose.


6. INSTALL WATER OUTLET

  1. A102174E01
    Install a new gasket to the cylinder head as shown in the illustration.

    HINT:
    Make sure the claws of the gasket face the water outlet.

  1. Install the water outlet with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


7. INSTALL INTAKE MANIFOLD
  1. Temporarily install a new gasket and the intake manifold with the 4 bolts and 2 nuts.

  1. A172284E01
    Tighten the 4 bolts and 2 nuts in the order shown in the illustration.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    NOTICE:
    Make sure that the swirl control valve actuator is not damaged by the surrounding parts.


8. INSTALL MANIFOLD STAY
  1. Install the manifold stay with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


9. INSTALL GLOW PLUG ASSEMBLY
(Click here)

10. INSTALL NO. 2 CYLINDER BLOCK INSULATOR

11. INSTALL THERMOSTAT

A110388E09
  1. Install a new gasket onto the thermostat.

    HINT:
    When installing the thermostat onto the gasket, be careful not to deform the gasket. Make sure that the thermostat is properly installed into the groove of the gasket as shown in the illustration.

  1. Insert the thermostat into the cylinder block with the jiggle valve facing straight upward.

    HINT:
    The jiggle valve may be set within 30° on either side of the prescribed position.


12. INSTALL WATER INLET
  1. Install the water inlet with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


13. INSTALL NO. 2 WATER BY-PASS PIPE
  1. Install a new gasket and the No. 2 water by-pass pipe with the bolt and 2 nuts.

    Torque:
    for bolt:
    23 N*m{ 2354 kgf*cm , 17 ft.*lbf }
    for nut:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


14. INSTALL CRANKSHAFT PULLEY
  1. Align the pulley set key with the key groove of the pulley and install the pulley.

  1. A142434E01
    Using SST, install the pulley bolt.
    SST
    09213-58014  
    09330-00021  

    Torque:
    365 N*m{ 3722 kgf*cm , 269 ft.*lbf }


15. INSTALL FUEL SUPPLY PUMP ASSEMBLY
(Click here)

16. INSTALL COMMON RAIL ASSEMBLY
(Click here)

17. INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
  1. Temporarily install the No. 2 nozzle leakage pipe with the 3 bolts.

  1. Temporarily install a new gasket and the union bolt.

  1. Tighten the 3 bolts and union bolt.

    Torque:
    for bolt:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }
    for union bolt:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the 3 fuel hoses.


18. INSTALL VACUUM SWITCHING VALVE BRACKET
  1. Install the vacuum switching valve bracket with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 vacuum hoses and vacuum switching valve connector.


19. INSTALL EGR COOLER ASSEMBLY
(Click here)

20. INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY
(Click here)

21. INSTALL DIESEL THROTTLE BODY ASSEMBLY
  1. Install a new gasket and the diesel throttle body with the 2 bolts and 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 diesel throttle body connectors.

  1. w/o DPF:

    1. Install the wire harness clamp with the bolt.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    2. Connect the diesel turbo pressure sensor connector and vacuum switching valve connector.


22. INSTALL CAMSHAFT POSITION SENSOR

A102907
  1. Apply a light coat of engine oil to the O-ring of the camshaft position sensor.

  1. A102283
    Install the camshaft position sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Do not crack or jam the O-ring when installing the camshaft position sensor.

  1. Connect the camshaft position sensor connector.


23. INSTALL CRANKSHAFT POSITION SENSOR

A102906
  1. Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.

  1. A151576
    Install the crankshaft position sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Do not crack or jam the O-ring when installing the crankshaft position sensor.

  1. Connect the 3 wire harness clamps.

  1. A102284
    Connect the crankshaft position sensor to the No. 1 vacuum pipe.

  1. Connect the crankshaft position sensor connector.


24. INSTALL ENGINE COOLANT TEMPERATURE SENSOR

  1. A239516E01
    Using SST, install a new gasket and the engine coolant temperature sensor.
    SST
    09817-33190  

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }


25. INSTALL TIMING BELT
(Click here)

26. INSTALL VACUUM PUMP ASSEMBLY
  1. Install 2 new O-rings to the vacuum pump.

  1. Install the vacuum pump with the 2 nuts.

    Torque:
    21 N*m{ 210 kgf*cm , 15 ft.*lbf }


27. INSTALL TIMING GEAR COVER INSULATOR
  1. Install the timing gear cover insulator with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


28. INSTALL VANE PUMP ASSEMBLY
  1. Install a new vane pump O-ring to the vane pump assembly.

  1. C101372E01
    Install the vane pump assembly with the 2 nuts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    NOTICE:
    Make sure that the vane pump O-ring is not caught between other parts.


29. INSTALL ENGINE WIRE
  1. Install the engine wire to the engine.


30. REMOVE ENGINE STAND

  1. A239319E01
    Install 2 engine hangers with 2 bolts as shown in the illustration.

    HINT:
    Part No.
    No. 1 Engine Hanger
    12284-30020
    No. 2 Engine Hanger
    12282-67020
    Bolt
    91552-81014 and 91642-81030

    Torque:
    for No. 1 engine hanger:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    for No. 2 engine hanger:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

    NOTICE:
    Install the engine hangers with new bolts.


31. INSTALL FRONT ENGINE MOUNTING INSULATOR

  1. A239331E01
    Install the 2 front engine mounting insulators and 2 engine mounting stabilizers with the 2 nuts.

    Torque:
    for Nut Type A:
    76 N*m{ 775 kgf*cm , 56 ft.*lbf }
    for Nut Type B:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }


32. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
  1. Install the front suspension crossmember with the 4 bolts.

    Torque:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }


33. CONNECT PRESSURE FEED TUBE ASSEMBLY
  1. Install a new gasket to the pressure feed tube assembly.

  1. C101371E01
    Connect the pressure feed tube assembly to the vane pump assembly with the union bolt.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

    HINT:
    Make sure the stopper of the pressure feed tube assembly contacts the vane pump assembly as shown in the illustration.


34. CONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE

  1. C101370E01
    Connect the No.1 oil reservoir to pump hose to the vane pump assembly with the clip.


35. INSTALL ENGINE ASSEMBLY
  1. Set an engine lifter in place.

  1. Operate the engine lifter and install the engine to the vehicle.

  1. A101144E05
    Install the engine with crossmember with the 16 bolts.

    Torque:
    for bolt A:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    for bolt B:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }
    for bolt C:
    150 N*m{ 1530 kgf*cm , 111 ft.*lbf }


36. CONNECT STEERING TORQUE SHAFT ASSEMBLY

  1. C106143E01
    Align the matchmarks on the steering torque shaft assembly and the power steering link assembly.

  1. C106142E01
    Install bolt (B) and tighten the 2 bolts.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }


37. CONNECT SHOCK ABSORBER ASSEMBLY FRONT LH
(Click here)

38. CONNECT SHOCK ABSORBER ASSEMBLY FRONT RH

HINT:
Use the same procedures described for the LH side.


39. CONNECT FRONT SUSPENSION ARM SUB-ASSEMBLY UPPER LH

  1. C102007E02
    Connect the front suspension upper arm to the steering knuckle with the nut.

    Torque:
    113 N*m{ 1,150 kgf*cm , 83 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    1. If the holes for the cotter pin are not aligned, tighten the nut up to 60°.
    2. Do not damage the ball joint dust cover.


40. CONNECT FRONT SUSPENSION ARM SUB-ASSEMBLY UPPER RH

HINT:
Use the same procedures described for the LH side.


41. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH

  1. C102283E01
    Install the brake caliper assembly to the steering knuckle with the 2 bolts.

    Torque:
    123 N*m{ 1,250 kgf*cm , 91 ft.*lbf }


42. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


43. INSTALL SPEED SENSOR FRONT LH (w/ ABS)

  1. C112932E01
    Connect the front speed sensor with the 2 bolts and 2 clips.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Do not twist the sensor wire when installing.
    2. Keep the sensor tip free from foreign matter.


44. INSTALL SPEED SENSOR FRONT RH (w/ ABS)

HINT:
Use the same procedures described for the LH side.


45. INSTALL REAR END PLATE
  1. Install the rear end plate with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


46. INSTALL FLYWHEEL SUB-ASSEMBLY
  1. for Manual Transmission:
    Apply adhesive to 2 or 3 threads of each of the 8 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.

  1. A142434E01
    Using SST, hold the crankshaft pulley.
    SST
    09213-58014  
    09330-00021  

  1. for Manual Transmission

    1. A114803E01
      Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.

      Torque:
      178 N*m{ 1815 kgf*cm , 131 ft.*lbf }

  1. for Automatic Transmission.

    1. A236848E01
      Install the flywheel and ring gear, the pump impeller drive plate and the rear drive plate spacer to the crankshaft.

      NOTICE:
      Align either hole in the pump impeller drive plate and either hole in the rear drive plate spacer with the knock pin of the flywheel and ring gear, and then install the flywheel and ring gear, the pump impeller drive plate and the rear drive plate spacer to the crankshaft.

      HINT:
      As the rear drive plate spacer and pump impeller drive plate are not reversible, be sure to install them in the direction shown in the illustration.

    2. A242998E01
      Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

      Torque:
      178 N*m{ 1815 kgf*cm , 131 ft.*lbf }


47. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

  1. C104159E01
    Insert SST into the clutch disc assembly, then insert them into the flywheel sub-assembly.
    SST
    09301-00110  

    NOTICE:
    Take care not to insert the clutch disc assembly in the wrong direction.


48. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

  1. C114265E02
    Align the matchmarks on the clutch cover assembly with the one on the flywheel sub-assembly.

  1. Following the procedures shown in the illustration, tighten the 6 bolts starting from the bolt located near the knock pin on the top.

    SST
    09301-00110  

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

    HINT:
    1. Evenly tighten the bolts by following the order shown in the illustration.
    2. Tighten the bolts after checking that the disc is in the center by lightly moving the SST up and down, left and right.


49. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)

  1. C086210
    Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

    Maximum non-alignment:
    1.3 mm (0.051 in.)

  1. C114266E01
    If alignment is not as specified, adjust the diaphragm spring tip alignment using SST.
    SST
    09333-00013  


50. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
(Click here)

51. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)

52. INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY
  1. Connect the vane pump oil reservoir with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


53. CONNECT ENGINE ROOM MAIN WIRE
  1. Install the nut and close the cover.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Connect the 5 connectors.

  1. Attach the clamp and connect the engine room main wire.


54. CONNECT ENGINE WIRE
  1. Attach the 3 clamps.

  1. Connect the 4 connectors.

  1. Connect the ECM connector (Click here).

  1. Install the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


55. CONNECT VACUUM HOSE
  1. Connect the vacuum hose to the vacuum pump.


56. CONNECT NO. 1 FUEL HOSE
  1. Connect the No. 1 fuel hose to the fuel supply pump.


57. CONNECT NO. 2 FUEL HOSE
  1. Connect the No. 2 fuel hose to the No. 2 nozzle leakage pipe.


58. CONNECT NO. 3 WATER BY-PASS HOSE
  1. Connect the No. 3 water by-pass hose to the No. 2 water by-pass pipe.


59. CONNECT NO. 4 RADIATOR HOSE
  1. Connect the No. 4 radiator hose to the water inlet.


60. CONNECT RADIATOR HOSE INLET
  1. Connect the radiator hose inlet to the water outlet.


61. INSTALL NO. 4 AIR HOSE
  1. Install the No. 4 air hose to the diesel throttle body.


62. CONNECT OIL RETURN HOSE
  1. Connect the oil return hose to the intake manifold.


63. INSTALL EXHAUST MANIFOLD
  1. Set a new gasket on the cylinder head.

  1. Install the exhaust manifold, 8 collars and 8 plate washers with 8 new nuts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    NOTICE:
    Install the collars so that the side with the smaller external diameter faces the exhaust manifold.


64. INSTALL TURBOCHARGER SUB-ASSEMBLY
(Click here)

65. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

  1. A101148E01
    Install the V-ribbed belt tensioner with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    HINT:
    Firmly press and hold the tensioner against the cylinder block to eliminate any gaps in the areas labeled A in the illustration. Then uniformly tighten the 4 bolts.


66. INSTALL GENERATOR ASSEMBLY
(Click here)

67. INSTALL NO. 2 IDLE PULLEY ASSEMBLY (w/ Air Conditioning System)
  1. Install the spacer, No. 2 idle pulley and pulley plate with the bolt.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }


68. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

  1. A102453E02
    Temporarily install the No. 1 compressor mounting bracket with the 4 bolts.

    HINT:
    Make sure that the No. 1 compressor mounting bracket is in contact with the cylinder block.

  1. Tighten the 4 bolts in the sequence shown in the illustration.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }


69. INSTALL COMPRESSOR OUTLET ELBOW

  1. A313566E01
    Install the compressor outlet elbow with the 2 hose clamps and bolt.

    Torque:
    for bolt:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    for hose clamp A:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }
    for hose clamp B:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


70. INSTALL AIR TUBE ASSEMBLY

  1. A272217E01
    Install the air tube assembly and No. 1 air cleaner hose with the 2 bolts.

    Torque:
    for bolt A:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
    for bolt B:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Tighten the 2 hose clamps.


71. INSTALL NO. 1 AIR CLEANER HOSE
  1. Connect the No. 1 air cleaner hose to the compressor inlet elbow.

    NOTICE:
    Pull the hose to make sure that it is locked and securely connected.


72. INSTALL FRONT EXHAUST PIPE ASSEMBLY
(Click here)

73. TEMPORARILY INSTALL FAN PULLEY
  1. Temporarily install the fan pulley with the 4 nuts.


74. INSTALL FAN AND GENERATOR V BELT
  1. Rotate the V-ribbed belt tensioner pulley clockwise, and then install the fan and generator V belt.

    NOTICE:
    Make sure that the fan and generator V belt is set properly on each pulley.

  1. Check that the indicator mark of the V-ribbed belt tensioner (Click here).


75. TIGHTEN FAN PULLEY
  1. Tighten the 4 nuts and install the fan pulley.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }


76. ADD ENGINE OIL
  1. Add new engine oil.

    Standard Oil Grade:
    Item
    Oil Grade
    Oil Viscosity (SAE)
    w/ DPF
    ACEA C2
    (Using engine oil other than ACEA C2 may damage catalytic converter)
    - 0W-30
    - 5W-30
    w/o DPF
    G-DLD1, API CF-4, CF or ACEA B1
    (You may also use API CE or CD)
    - 5W-30
    - 10W-30
    - 15W-40
    - 20W-50


    Standard Capacity (w/ DPF):
    Item
    Fill Amount
    Drain and refill without oil filter change
    6.6 liters (7.0 US qts, 5.8 Imp. qts)
    Drain and refill with oil filter change
    6.8 liters (7.2 US qts, 6.0 Imp. qts)
    Dry fill
    7.5 liters (7.9 US qts, 6.6 Imp. qts)


    Standard Capacity (w/o DPF):
    Item
    Fill Amount
    Drain and refill without oil filter change
    6.8 liters (7.2 US qts, 6.0 Imp. qts)
    Drain and refill with oil filter change
    7.0 liters (7.4 US qts, 6.2 Imp. qts)
    Dry fill
    7.7 liters (8.1 US qts, 6.8 Imp. qts)

  1. Install the oil filler cap.


77. ADD ENGINE COOLANT
  1. Firmly tighten the drain plugs.

  1. Fill the radiator reservoir assembly with engine coolant to the top of the inlet.

    Standard Capacity:
    Item
    Specified Condition
    w/o Heater
    13.2 liters (13.9 US qts, 11.6 Imp. qts)
    w/ Front Heater
    14.2 liters (15.0 US qts, 12.5 Imp. qts)
    w/ Front and Rear Heaters
    16.2 liters (17.1 US qts, 14.3 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. Loosen the bleeder plug of the outlet housing.

  1. When air is bled and the engine coolant drains out, firmly tighten the bleeder plug.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. A142533
    Add engine coolant up to the B line mark in the radiator reservoir assembly and install the radiator reservoir cap sub-assembly.

  1. Warm up the engine until the thermostat opens.

    1. While the thermostat is open, circulate the engine coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by pressing the No. 3 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. A142532
    After the engine cools down, check that the engine coolant level is between the LOW and FULL level marks.


78. ADD POWER STEERING FLUID

79. ADD MANUAL TRANSMISSION OIL (for Manual Transmission)

  1. D025304E01
    Park the vehicle in a level place.

  1. Remove the transmission filler plug and gasket.

  1. Check that the oil surface is within 5 mm (0.20 in.) below the lowest point of the transmission filler plug opening.

    Oil grade:
    API GL-4
    Viscosity:
    SAE 75W-90
    Capacity:
    2.6 liters (2.7 US qts, 2.3 Imp.qts)

    NOTICE:
    1. Problems may occur when the oil level is too high or too low.
    2. After replacing the oil, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install the transmission filler plug and a new gasket.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


80. ADD AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

81. CHARGE REFRIGERANT (w/ Air Conditioning System)
  1. Perform vacuum purging using a vacuum pump.

  1. Charge with refrigerant HFC-134a (R134a).

    E100257E01

    Standard:
    Single A/C:
    520 to 580g (18.3 to 20.5 oz.)
    Dual A/C:
    670 to 730g (23.0 to 25.7 oz.)

    SST
    07110-58060   (07117-58090, 07117-78050, 07117-58070, 07117-58060, 07117-58080, 07117-88060, 07117-88070, 07117-88080)

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor does not work properly without any refrigerant, which causes the compressor to overheat.
    2. Approximately 100 g (3.5 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, and not with the sight glass.

    HINT:
    Prepare a service can to recharge refrigerant if using the refrigerant gas collected with the freon collection/recycling device because the collective rate of the device is approximately 90%.


82. BLEED AIR FROM FUEL SYSTEM

  1. A239557E01
    Using the hand pump mounted on the fuel filter cap, bleed air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/ sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Check if the engine starts.

    NOTICE:
    1. Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.


    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs.

    1. w/ DPF: (Click here)
    2. w/o DPF: (Click here)

  1. Start the engine.*1

  1. A194065E03
    Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3

  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

    A192848E05

    HINT:
    When the Active Test "Test the Fuel Leak" is used to change the pump control mode, the actual fuel pressure inside the common rail drops below the target fuel pressure when the Active Test is off, but this is normal and does not indicate a pump malfunction.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

  1. Clear the DTCs.

    1. w/ DPF: (Click here)
    2. w/o DPF: (Click here)

    HINT:
    It is necessary to clear the DTCs as DTC P1604 or P1605 may be stored when air is bled from the fuel system after replacing or repairing fuel system parts.

  1. Repeat steps *1 to *3.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

    OK:
    No DTCs are output.


83. BLEED POWER STEERING FLUID
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the steering wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

    1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the steering wheel left or right to the full lock position and keep it there for 2 to 3 seconds, then turn the steering wheel to the opposite full lock position and keep it there for 2 to 3 seconds.

    2. Repeat several times.

  1. Stop the engine.

  1. F040897E03
    Check for foaming or emulsification.
    If the system has to be bled twice because of forming or emulsification, be sure to check for fluid leaks in the system.

  1. Check the fluid level (Click here).


84. INSPECT FOR FUEL LEAK
  1. Perform the Active Test.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test.

    5. Perform the Active Test.

      Tester Display
      Test Part
      Control Range
      Diagnostic Notes
      Test the Fuel Leak
      Pressurize common rail interior and check for fuel leaks
      Stop/Start
      1. Fuel pressure inside common rail increased to specified value and engine speed increased to 2000 rpm when Active Test is performed
      2. Above conditions preserved while Active Test is being performed


85. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.


86. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Hot, pressurized engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester to the radiator.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 137 kPa (1.4 kgf/cm2, 19.9 psi), and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


87. INSPECT FOR POWER STEERING FLUID LEAK

88. CHECK ENGINE OIL LEVEL
  1. Warm up the engine, stop the engine and wait for 5 minutes.

  1. Check that the oil level is between the upper level and lower level of the engine oil level dipstick.
    If the oil level is low, check for leakage and add oil up to the upper level of the oil level dipstick.


89. INSPECT POWER STEERING FLUID LEVEL

90. INSPECT AUTOMATIC TRANSMISSION FLUID LEVEL (for Automatic Transmission)

HINT:
Drive the vehicle so that the engine and transmission are at normal operating temperature.

Fluid temperature:
70 to 80 °C (158 to 176 °F)

  1. D025120E01
    Park the vehicle on a level surface and set the parking brake.

  1. With the engine idling and the brake pedal depressed, move shift the lever into all positions from P to L and return to the P position.

  1. Take out the dipstick and wipe it clean.

  1. Put it back all the way.

  1. Take it out again and check that the fluid level is within the HOT range.
    If the fluid level is below the HOT range, add new fluid and recheck the fluid level. If the fluid level exceeds the HOT range, drain the fluid once, add the proper amount of new fluid and recheck the fluid level.


91. INSPECT SHIFT LEVER POSITION (for Automatic Transmission)
  1. When shifting from P position only with ignition switch ON and depress the break pedal.

  1. Make sure that the shifting lever moves smoothly and can be moderately operated.

  1. When starting engine, make sure that the vehicle moves forward when shifting from N to D position and moves reward when shifting R position.


92. ADJUST SHIFT LEVER POSITION (for Automatic Transmission)

  1. C101771E02
    Remove a clip, nut, and disconnect between the control shaft lever to transmission control cable assembly from the control shaft lever and transmission control cable bracket No.1.

  1. C101788E05
    Turn the control shaft lever until stop to a clockwise direction, return the control shaft lever 2 notches to N position.

  1. C101803
    Set the shift lever to N position while holding the shift lever lightly toward the R position side and install it.

    Torque:
    15 N*m{ 150 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Tighten the nut with it closing up cranky.

  1. Inspect the operation condition and work.


93. INSPECT FOR EXHAUST GAS LEAK

94. INSPECT FOR REFRIGERANT LEAK (w/ Air Conditioning System)
  1. After recharging refrigerant gas, check for leakage of refrigerant gas using a halogen leak detector.

  1. Carry out the test under the following conditions:

    1. Stop the engine.
    2. Secure good ventilation (the gas leak detector may react to volatile gases which are not refrigerant, such as evaporated gasoline and exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that there is some refrigerant remaining in the refrigeration system.
      When the compressor is off: approx. 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)

  1. I042222E02
    Using a gas leak detector, check for leakage of the refrigerant line.

  1. N014519E01
    Bring the gas leak detector close to the drain hose with the detector's power off.

    HINT:
    1. After the blower motor has stopped, let the cooling unit stand for more than 15 minutes.
    2. Bring the gas leak detector sensor under the drain hose.
    3. When bringing the gas leak detector close to the drain hose, make sure that the gas leak detector does not react to volatile gases.
      If such reaction is unavoidable, the vehicle must be lifted up.

  1. If a gas leak is not detected on the drain hose, remove the blower motor control from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.


95. INSTALL NO. 2 ENGINE UNDER COVER (for Cold Area Specification Vehicles)
  1. Install the No. 2 engine under cover with the 6 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


96. INSTALL NO. 1 ENGINE UNDER COVER (for Cold Area Specification Vehicles)
  1. Install the No. 1 engine under cover with the 4 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


97. INSTALL NO. 2 ENGINE SERVICE HOLE COVER (for Standard Body)
  1. Install the No. 2 engine service hole cover with the 3 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Return the carpet to its original position and attach the clips.


98. INSTALL ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Install the engine service hole sub cover with the 5 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


99. INSTALL FRONT DOOR SCUFF PLATE RH

100. INSTALL FRONT SEAT ASSEMBLY RH

  1. B107528
    Connect the front seat inner belt assembly connector and install the front seat assembly.

  1. Align the front seat assembly adjuster pin with the holes in the body.

  1. Move the front seat assembly to the rearmost position.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Temporarily tighten the 2 bolts on the front side of the front seat assembly.

  1. Move the front seat assembly fully forward.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Temporarily tighten the 2 bolts on the rear side of the front seat assembly.

  1. Move the front seat assembly to the rearmost position.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of outer and inner side.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

  1. Move the front seat assembly fully forward.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of outer and inner side.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }


101. CHECK ENGINE IDLING SPEED AND MAXIMUM SPEED

NOTICE:
Turn all electrical systems off.

  1. Warm up and stop the engine.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

      HINT:
      Refer to the intelligent tester operator's manual for further information regarding the selection of the Data List.

    4. Inspect the engine idling speed.

      Idling speed:
      700 to 800 rpm

    5. Fully depress the accelerator pedal.

    6. Check the maximum speed.

      Maximum speed:
      4500 to 4700 rpm

    7. Turn the ignition switch off.

    8. Disconnect the intelligent tester from the DLC3.

  1. A206183E07
    When not using the intelligent tester:

    1. Install SST to terminal 9 (TAC) of DLC3, and then connect a tachometer.

      SST
      09843-18040  
      Text in Illustration 
      *a
      Front view of DLC3

      NOTICE:
      Examine the terminal numbers before connecting them. Connecting SST to the wrong terminal can damage the engine.

    2. Turn the ignition switch to ON.

    3. Inspect the engine idling speed.

      Idling speed:
      700 to 800 rpm

    4. Fully depress the accelerator pedal.

    5. Check the maximum speed.

      Maximum speed:
      4500 to 4700 rpm

    6. Turn the ignition switch off.

    7. Disconnect the tachometer.

    8. Remove SST from terminal 9.


102. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)

103. INSPECT ABS SENSOR SIGNAL
(Click here)
← INSTALLATION (Oct 2014 – Nov 2017)PRECAUTION (from Oct 2014) →