2014-2019 Hiace · Service Manual BRAKE

C0200/31 Front Speed Sensor RH Circuit

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION


  1. The speed sensor detects wheel speed and transmits the appropriate signals to the ECU. These signals are used for control of the ABS control system. The front and rear rotors have 48 serrations each.
    When the rotors rotate, the magnetic field generated by the permanent magnet in the speed sensor induces an AC voltage.
    Since the frequency of this AC voltage changes in direct proportion to the speed of the rotor, the frequency is used by the ECU to detect the speed of each wheel.
    DTCs C1271/71 to C1276/76 can be deleted when the speed sensor sends a vehicle speed signal or the Test Mode ends. DTCs C1271/71 to C1276/ 76 are output only in the Test Mode.
    F000010E04
    DTC No.
    DTC Detection Condition
    Trouble Area
    C0200/31
    C0205/32
    With vehicle speed at 6 mph (10 km/h) or more, sensor signal circuit of faulty wheel is open or short for 1 second or more.
    1. Momentary interruption of sensor signal of faulty wheel has occurred 7 times or more.
    1. Sensor signal circuit is open for 0.5 seconds or more.
    1. Front speed sensor RH/LH
    2. Front speed sensor RH/LH circuit
    3. Skid control rotor
    4. Sensor installation
    5. Brake actuator assembly
    C1235/35
    C1236/36
    At vehicle speed of 12 mph (20 km/h) or more, condition that noise is included in speed sensor signal continues for 5 seconds or more.
    1. Front speed sensor RH/LH
    2. Skid control rotor
    3. Sensor installation
    4. Brake actuator assembly

    HINT:
    1. DTC No. C0200/31 and C1235/35 are for the front speed sensor RH.
    2. DTC No. C0205/32 and C1236/36 are for the front speed sensor LH.


WIRING DIAGRAM

C109415E01

INSPECTION PROCEDURE

HINT:
Start the inspection from step 1 when using the intelligent tester and start from step 3 when not using the intelligent tester.


1. READ VALUE USING INTELLIGENT TESTER (MOMENTARY INTERRUPTION OF FRONT SPEED SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the intelligent tester main switch on.

  1. Select the DATA LIST mode on the intelligent tester.

    ABS: 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    FR Speed Open
    Speed sensor open detection (FR) / OPN DET or NORMAL
    OPN DET: Momentary interruption
    NORMAL: Normal
    -
    FL Speed Open
    Speed sensor open detection (FL) / OPN DET or NORMAL
    OPN DET: Momentary interruption
    NORMAL: Normal
    -

  1. Check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).

    OK:
    There are no momentary interruptions.

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK


2. READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR)
  1. Select the DATA LIST mode on the intelligent tester.

    ABS: 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Wheel speed sensor (FR) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h)
    Actual wheel speed
    Similar speed as indicated on speedometer
    FL Wheel Speed
    Wheel speed sensor (FL) reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h)
    Actual wheel speed
    Similar speed as indicated on speedometer

  1. Check that there is the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer are almost the same when driving the vehicle.

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed.



NG
Go to step 4
OK


3. PERFORM TEST MODE (SIGNAL CHECK)
  1. Clear the DTC (Click here).

  1. Perform sensor signal check in TEST MODE PROCEDURE (Click here).

    OK:
    All Test Mode DTCs are erased.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 9
A


4. INSPECT FRONT SPEED SENSOR INSTALLATION

  1. BR03795E96
    Turn the ignition switch off.

  1. Check the speed sensor installation.

    OK:
    The installation bolt is tightened properly.
    There is no clearance between the sensor and the front steering knuckle.
    Torque:
    8.5 N*m (87kgf*cm, 75 in.*lbf)

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
INSTALL FRONT SPEED SENSOR CORRECTLY OR REPLACE FRONT SPEED SENSOR
OK


5. INSPECT SPEED SENSOR TIP
  1. Remove the front speed sensor (Click here).

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


6. INSPECT FRONT SPEED SENSOR

  1. C111156E01
    Install the front speed sensor.

  1. Disconnect the front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    RH Side: 
    Tester Connection
    Specified Condition
    2 (FR+) - 1 (FR-)
    1.6+-0.2 kΩ at 20°C
    2 (FR+) - Body ground
    10 kΩ or higher
    1 (FR-) - Body ground
    10 kΩ or higher
    LH Side: 
    Tester Connection
    Specified Condition
    2 (FL+) - 1 (FL-)
    1.6+-0.2 kΩ at 20°C
    2 (FL+) - Body ground
    10 kΩ or higher
    1 (FL-) - Body ground
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE FRONT SPEED SENSOR
OK


7. CHECK HARNESS AND CONNECTOR (BETWEEN SKID CONTROL ECU AND FRONT SPEED SENSOR)

  1. C111157E01
    Disconnect the skid control sensor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    RH: 
    Tester Connection
    Specified Condition
    B19-31 (FR+) - B18-2 (FR+)
    Below 1 Ω
    B19-31 (FR+) - Body ground
    10 kΩ or higher
    B19-30 (FR-) - B18-1 (FR-)
    Below 1 Ω
    B19-30 (FR-) - Body ground
    10 kΩ or higher
    LH: 
    Tester Connection
    Specified Condition
    B19-9 (FL+) - B20-2 (FL+)
    Below 1 Ω
    B19-9 (FL+) - Body ground
    10 kΩ or higher
    B19-8 (FL-) - B20-1 (FL-)
    Below 1 Ω
    B19-8 (FL-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. INSPECT SPEED SENSOR AND SENSOR ROTOR SERRATIONS

  1. W004200E03
    Connect the oscilloscope to terminals FR+ - FR- or FL+ - FL- of the skid control ECU.

  1. Drive the vehicle at about 19 mph (30 km/h), and check the signal waveform.

    OK:
    A waveform as shown in the figure should be output.

    HINT:
    1. As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the fluctuation in the output voltage becomes greater.
    2. When noise is identified in the waveform on the oscilloscope, error signals are generated due to rotor scratches, looseness or foreign matter attached to the speed sensor.



NG
Go to step 10
OK


9. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 20 mph (32 km/h) or more for 60 seconds or more.

  1. Check that the same DTCs are recorded (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:
    Condition
    Proceed to
    DTCs (C0200/31, C0205/32, C1235/35 and C1236/36) are output
    A
    DTCs (C0200/31, C0205/32, C1235/35 and C1236/36) are not output (When troubleshooting in accordance with the DTC CHART)
    B
    DTCs (C0200/31, C0205/32, C1235/35 and C1236/36) are not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
    C



B
END

C
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
A


10. INSPECT FRONT SKID CONTROL ROTOR
  1. Turn the ignition switch off.

  1. Remove the front axle hub (Click here).

  1. Check the rotor.

    OK:
    No scratches, oil, or foreign matter on the rotors.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE FRONT SKID CONTROL ROTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY


← DIAGNOSTIC TROUBLE CODE CHART (from Jan 2017)C0200/31 Front Speed Sensor RH Circuit (+ 7 more codes) (Jan 2015 – Dec 2016) →