C0200/31 Front Speed Sensor RH Circuit
Diagnostic trouble codes · Vehicles built from Jan 2017
Also covers:
- C0205/32 Front Speed Sensor LH Circuit
- C1235/35 Foreign Object is Attached on Tip of Front Speed Sensor RH
- C1236/36 Foreign Object is Attached on Tip of Front Speed Sensor LH
- C1271/71 Low Output Signal of Front Speed Sensor RH (Test Mode DTC)
- C1272/72 Low Output Signal of Front Speed Sensor LH (Test Mode DTC)
- C1275/75 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)
- C1276/76 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017
DESCRIPTION
-
The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for ABS control.
The speed sensor generates vehicle speed pulses based on the rotation of the skid control rotor. The skid control ECU (brake actuator assembly) detects the speed of each wheel using this vehicle speed pulse.
DTCs C1271/71 to C1276/76 can be cleared when the speed sensor sends a vehicle speed signal or the Test Mode ends. DTCs C1271/71 to C1276/ 76 are output only in the Test Mode.- HINT:
- When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


Text in Illustration *1
Front Speed Sensor
*2
Front Skid Control Rotor
*a
Waveform (Reference):
Between Speed Sensor (-) and Body Ground
*b
Low speed
*c
High speed
-
-
DTC No.
DTC Detection Condition
Trouble Area
C0200/31
C0205/32
- With the vehicle speed 10 km/h (6 mph) or higher, an open or short circuit in the speed sensor signal circuit continuously occurs for 15 seconds or more.
- An open in the speed sensor signal circuit continues for 0.5 seconds or more.
- From when the ignition switch is turned to ON until it is turned off, a speed sensor momentary open circuit signal occurs 255 times or more.
- Front speed sensor RH/LH
- Front speed sensor RH/LH circuit
- Skid control rotor
- Sensor installation
- Skid control ECU (brake actuator assembly)
C1235/35
C1236/36
With the vehicle speed 20 km/h (12 mph) or higher, noise is detected 75 times in the speed sensor signal within 5 seconds.
- Front speed sensor RH/LH
- Skid control rotor
- Sensor installation
- Skid control ECU (brake actuator assembly)
C1271/71
C1272/72
Detected only during Test Mode.
- Front speed sensor RH/LH
- Sensor installation
- Skid control rotor
C1275/75
C1276/76
Detected only during Test Mode.
- Front speed sensor RH/LH
- Skid control rotor
- HINT:
- DTC No. C0200/31 and C1235/35 are for the front speed sensor RH.
- DTC No. C0205/32 and C1236/36 are for the front speed sensor LH.
- DTC No. C0200/31 and C1235/35 are for the front speed sensor RH.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION OF FRONT SPEED SENSOR) |
Using a GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Speed Open
Front speed sensor RH open detection / Error or Normal
Normal
Error: Momentary interruption
FL Speed Open
Front speed sensor LH open detection / Error or Normal
Normal
Error: Momentary interruption
- OK:
- Normal (There are no momentary interruptions.)
- HINT:
- Perform the above inspection before removing the sensor and connector.
|
|
||||
| OK | |
| 2. READ VALUE USING GTS (FRONT SPEED SENSOR) |
Select the DATA LIST mode on the GTS.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Wheel Speed
Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
FL Wheel Speed
Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
Check that the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer are almost the same when driving the vehicle.
- OK:
- The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed.
|
|
||||
| OK | |
| 3. PERFORM TEST MODE (SIGNAL CHECK) |
Perform sensor signal check in TEST MODE PROCEDURE (Click here).
- OK:
- All Test Mode DTCs are cleared.
|
|
||||
| OK | |
| 4. RECONFIRM DTC |
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.
Check that the same DTCs are recorded (Click here).
- Result:
Result
Proceed to
DTC is not output
A
DTC is output
B
- HINT:
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
| A | ||
| ||
| 5. INSPECT FRONT SPEED SENSOR INSTALLATION |
Turn the ignition switch off.
Check the speed sensor installation (Click here).

- OK:
- There is no clearance between the sensor and the front steering knuckle.
- The installation bolt is tightened properly.
Text in Illustration *a
Normal
*b
Abnormal
*c
Clearance
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 6. INSPECT SPEED SENSOR TIP |
Remove the front speed sensor (Click here).
Check the sensor tip.
- OK:
- No scratches or foreign matter on the sensor tip.
- NOTICE:
- If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
- If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.
- Check the speed sensor signal after cleaning or replacement (Click here).
- If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
|
|
||||
| OK | |
| 7. INSPECT FRONT SKID CONTROL ROTOR |
Remove the front skid control rotor (Click here).
Check the front skid control rotor.
- OK:
- No scratches, oil, or foreign matter on the rotors.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
Reinstall the front speed sensor and the front skid control rotor (Click here for speed sensor, Click here for skid control rotor).
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the B19 skid control ECU (brake actuator assembly) connector and the B18 and/or B20 front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RH Tester Connection
Condition
Specified Condition
B19-31 (FR+) - B18-2
Always
Below 1 Ω
B19-31 (FR+) or B18-2 - Body ground
Always
10 kΩ or higher
B19-30 (FR-) - B18-1
Always
Below 1 Ω
B19-30 (FR-) or B18-1 - Body ground
Always
10 kΩ or higher
for LH Tester Connection
Condition
Specified Condition
B19-9 (FL+) - B20-2
Always
Below 1 Ω
B19-9 (FL+) or B20-2 - Body ground
Always
10 kΩ or higher
B19-8 (FL-) - B20-1
Always
Below 1 Ω
B19-8 (FL-) or B20-1 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 9. INSPECT BRAKE ACTUATOR ASSEMBLY |
Reconnect the B19 skid control ECU (brake actuator assembly) connector.

Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
for RH Tester Connection
Switch Condition
Specified Condition
B18-2 - Body ground
Ignition switch ON
5.7 to 14 V
for LH Tester Connection
Switch Condition
Specified Condition
B20-2 - Body ground
Ignition switch ON
5.7 to 14 V
Text in Illustration *A
for RH
*B
for LH
*a
Front view of wire harness connector
(to Front Speed Sensor)
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 10. RECONFIRM DTC |
Reconnect the B18 and/or B20 front speed sensor connector.
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.
Check that the same DTCs are recorded (Click here).
- Result:
Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | ||
| ||
| 11. REPLACE FRONT SPEED SENSOR |
Replace the front speed sensor (Click here).
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 12. RECONFIRM DTC |
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.
Check that the same DTCs are recorded (Click here).
- Result:
Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | ||
| ||
| 13. REPLACE FRONT SKID CONTROL ROTOR |
Replace the front skid control rotor (Click here).
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 14. RECONFIRM DTC |
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.
Check that the same DTCs are recorded (Click here).
- Result:
Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | ||
| ||
