2014-2019 Hiace · Service Manual BRAKE

C0200/31 Front Speed Sensor RH Circuit

Diagnostic trouble codes · Vehicles built Jan 2015 – Dec 2016

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION


  1. The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for ABS control.
    The speed sensor generates vehicle speed pulses based on the rotation of the skid control rotor. The skid control ECU (brake actuator assembly) detects the speed of each wheel using this vehicle speed pulse.
    DTCs C1271/71 to C1276/76 can be cleared when the speed sensor sends a vehicle speed signal or the Test Mode ends. DTCs C1271/71 to C1276/ 76 are output only in the Test Mode.

    HINT:
    When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.

    C321040E01
    Text in Illustration 
    *1
    Front Speed Sensor
    *2
    Front Skid Control Rotor
    *a
    Waveform (Reference):
    Between Speed Sensor (-) and Body Ground
    *b
    Low speed
    *c
    High speed
    -
    -
    DTC No.
    DTC Detection Condition
    Trouble Area
    C0200/31
    C0205/32
    1. With the vehicle speed 10 km/h (6 mph) or higher, an open or short circuit in the speed sensor signal circuit continuously occurs for 15 seconds or more.
    2. An open in the speed sensor signal circuit continues for 0.5 seconds or more.
    3. From when the ignition switch is turned to ON until it is turned off, a speed sensor momentary open circuit signal occurs 255 times or more.
    1. Front speed sensor RH/LH
    2. Front speed sensor RH/LH circuit
    3. Skid control rotor
    4. Sensor installation
    5. Skid control ECU (brake actuator assembly)
    C1235/35
    C1236/36
    With the vehicle speed 20 km/h (12 mph) or higher, noise is detected 75 times in the speed sensor signal within 5 seconds.
    1. Front speed sensor RH/LH
    2. Skid control rotor
    3. Sensor installation
    4. Skid control ECU (brake actuator assembly)
    C1271/71
    C1272/72
    Detected only during Test Mode.
    1. Front speed sensor RH/LH
    2. Sensor installation
    3. Skid control rotor
    C1275/75
    C1276/76
    Detected only during Test Mode.
    1. Front speed sensor RH/LH
    2. Skid control rotor

    HINT:
    1. DTC No. C0200/31 and C1235/35 are for the front speed sensor RH.
    2. DTC No. C0205/32 and C1236/36 are for the front speed sensor LH.


WIRING DIAGRAM

C321037E02

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION OF FRONT SPEED SENSOR)
  1. Using a GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    Front speed sensor RH open detection / Error or Normal
    Normal
    Error: Momentary interruption
    FL Speed Open
    Front speed sensor LH open detection / Error or Normal
    Normal
    Error: Momentary interruption

    OK:
    Normal (There are no momentary interruptions.)

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 8
OK


2. READ VALUE USING GTS (FRONT SPEED SENSOR)
  1. Select the DATA LIST mode on the GTS.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    FL Wheel Speed
    Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations

  1. Check that the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer are almost the same when driving the vehicle.

    OK:
    The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed.



NG
Go to step 5
OK


3. PERFORM TEST MODE (SIGNAL CHECK)
  1. Perform sensor signal check in TEST MODE PROCEDURE (Click here).

    OK:
    All Test Mode DTCs are cleared.



NG
Go to step 5
OK


4. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.

  1. Check that the same DTCs are recorded (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B

HINT:
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
Go to step 11
A

USE SIMULATION METHOD TO CHECK (Click here)

5. INSPECT FRONT SPEED SENSOR INSTALLATION
  1. Turn the ignition switch off.

  1. C100381E01
    Check the speed sensor installation (Click here).

    OK:
    There is no clearance between the sensor and the front steering knuckle.
    The installation bolt is tightened properly.

    Text in Illustration 
    *a
    Normal
    *b
    Abnormal
    *c
    Clearance

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
INSTALL FRONT SPEED SENSOR CORRECTLY OR REPLACE FRONT SPEED SENSOR
OK


6. INSPECT SPEED SENSOR TIP
  1. Remove the front speed sensor (Click here).

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.

    NOTICE:
    1. If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
    2. If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.
    3. Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


7. INSPECT FRONT SKID CONTROL ROTOR
  1. Remove the front skid control rotor (Click here).

  1. Check the front skid control rotor.

    OK:
    No scratches, oil, or foreign matter on the rotors.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).

  1. Reinstall the front speed sensor and the front skid control rotor (Click here for speed sensor, Click here for skid control rotor).



NG
CLEAN OR REPLACE FRONT SKID CONTROL ROTOR
OK


8. CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the B19 skid control ECU (brake actuator assembly) connector and the B18 and/or B20 front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    B19-31 (FR+) - B18-2
    Always
    Below 1 Ω
    B19-31 (FR+) or B18-2 - Body ground
    Always
    10 kΩ or higher
    B19-30 (FR-) - B18-1
    Always
    Below 1 Ω
    B19-30 (FR-) or B18-1 - Body ground
    Always
    10 kΩ or higher
    for LH 
    Tester Connection
    Condition
    Specified Condition
    B19-9 (FL+) - B20-2
    Always
    Below 1 Ω
    B19-9 (FL+) or B20-2 - Body ground
    Always
    10 kΩ or higher
    B19-8 (FL-) - B20-1
    Always
    Below 1 Ω
    B19-8 (FL-) or B20-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT BRAKE ACTUATOR ASSEMBLY

  1. C324032E02
    Reconnect the B19 skid control ECU (brake actuator assembly) connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH 
    Tester Connection
    Switch Condition
    Specified Condition
    B18-2 - Body ground
    Ignition switch ON
    5.7 to 14 V
    for LH 
    Tester Connection
    Switch Condition
    Specified Condition
    B20-2 - Body ground
    Ignition switch ON
    5.7 to 14 V

    Text in Illustration 
    *A
    for RH
    *B
    for LH
    *a
    Front view of wire harness connector
    (to Front Speed Sensor)

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


10. RECONFIRM DTC
  1. Reconnect the B18 and/or B20 front speed sensor connector.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.

  1. Check that the same DTCs are recorded (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
Go to step 11
A

USE SIMULATION METHOD TO CHECK (Click here)

11. REPLACE FRONT SPEED SENSOR
  1. Replace the front speed sensor (Click here).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


12. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.

  1. Check that the same DTCs are recorded (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
Go to step 13
A

END

13. REPLACE FRONT SKID CONTROL ROTOR
  1. Replace the front skid control rotor (Click here).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


14. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 30 km/h (19 mph) or more for 60 seconds or more.

  1. Check that the same DTCs are recorded (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

END


← C0200/31 Front Speed Sensor RH Circuit (+ 7 more codes) (Oct 2014 – Dec 2014)C0200/31 Front Speed Sensor RH Circuit (+ 7 more codes) (from Jan 2017) →