P2006 Intake Manifold Runner Control Stuck Closed (Bank 1)
Diagnostic trouble codes · Vehicles built from Jan 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
The swirl control valve is mounted on the intake manifold. The vacuum switching valve is used to change the vacuum to control the swirl control valve.The ECM determines the opening angle of the swirl control valve, and uses the vacuum switching valve (for swirl control valve) to change the vacuum applied to the actuator's diaphragm to open and close the swirl control valve.
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| After warming up engine, drive vehicle at an engine speed of 3200 rpm or more with high load for 1 minute or more.* |
When actual intake air volume detected by mass air flow meter continues to be smaller than volume estimated from boost pressure and intake air temperature sensor, ECM determines that swirl control valve is stuck closed (1 trip detection logic). |
|
- HINT:
- *: When the above driving pattern cannot be performed due to road conditions, etc., the swirl control valve can be determined to be functioning normally if mass air flow is 100 gm/sec. or more and MAP is 110 kPa or higher when the engine speed is at 4000 rpm with no load. However, no DTCs are stored when inspecting the vehicle with this method.
- The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
- Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.


| *1 |
ECM |
*2 |
Swirl Control Valve |
| *3 |
Vacuum Pump |
*4 |
Vacuum Switching Valve (for Swirl Control Valve) |
| *5 |
Swirl Control Valve Actuator |
- |
- |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the GTS. Freeze frame data records the engine condition when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2006) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
Result Result
Proceed to
P2006 is output
A
P2006 and other DTCs are output
B
- HINT:
- When MAP, mass air flow, Intake Air, and/or Intake Air Temp (Turbo) related DTCs are stored along with P2006, perform troubleshooting for those DTCs first.
- MAP-related DTCs: P0107 and P0108 (Click here).
- MAF-related DTCs: P0102 and P0103 (Click here).
- Intake Air-related DTCs: P0112 and P0113 (Click here).
- Intake Air Temp (Turbo) related DTCs: P007C and P007D (Click here).
|
|
||||
| A | |
| 2. CHECK AIR INTAKE SYSTEM |
Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.
Result Result
Proceed to
Leaks and/or blockages exist in the intake system
A
No leaks or blockages in the intake system
B
- HINT:
- Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.
- Check if the air cleaner element is significantly dirty.
- Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
- Using your hand, check whether the pipes and hoses in the intake system are securely connected.
- By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.
- Check for any modifications in the intake system made by the user.
- Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.
|
|
||||
| A | |
| 3. REPAIR OR REPLACE AIR INTAKE SYSTEM |
Repair or replace the malfunctioning part in the air intake system.
|
|
||||
| 4. CHECK INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION) |
Check the movement of the swirl control valve immediately after starting the engine.


Text in Illustration *1
Swirl Control Valve
-
-
- OK:
- Swirl control valve rod moves smoothly in the direction indicated by the arrow in the illustration.
|
|
||||
| OK | |
| 5. READ VALUE USING GTS (MAF AND MAP) |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and MAF.
Take a snapshot when the engine speed is maintained at 4000 rpm with no load.
Read the values of "MAP" and "MAF" in the Data List using the snapshot review function.
Result Result
Proceed to
MAF 100 gm/sec. or more and MAP 110 kPa or higher
C
MAP below 90 kPa
B
Except above
A
- HINT:
- The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
- The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.
- The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
|
|
||||
|
|
||||
| A | |
| 6. CLEAN MASS AIR FLOW METER |
Remove any deposits adhering to the mass air flow meter.
|
|
||||
| 7. CHECK AND REPLACE TURBOCHARGER SUB-ASSEMBLY |
Check the turbocharger sub-assembly (Click here).
Replace the turbocharger sub-assembly (Click here).
- HINT:
- It is only necessary to replace the part when the results of the inspection indicate a problem.
|
|
||||
| 8. CHECK CONNECTION OF VACUUM HOSE |
Check the connection of the swirl control valve system vacuum hose.
|
|
||||
| OK | |
| 9. PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE) |
![]() ![]() |
Disconnect the vacuum hoses from the VSV for swirl control valve.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.
Check the VSV operation when it is operated using the GTS.
- OK:
GTS Operation
Specified Condition
VSV ON
Air from port E flows out through port F
VSV OFF
Air from port E flows out through air filter
Reconnect the vacuum hoses.
|
|
||||
| OK | |
| 10. INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY |
Inspect the electric EGR control valve assembly (Click here).
- HINT:
- If there are any deposits adhering to the valve, clean the valve. When cleaning the valve, use diesel fuel or kerosene.
- When inspecting the electric EGR control valve assembly, make sure that the valve is fully closed.
- If there are any deposits adhering to the valve, clean the valve. When cleaning the valve, use diesel fuel or kerosene.
|
|
||||
|
|
||||
| 11. REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY |
Replace the electric EGR control valve assembly (Click here).
| NEXT | |
| 12. INSPECT INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION) |
Inspect the intake manifold (swirl control valve) (Click here).
- HINT:
- If there are any deposits adhering to the valve, clean the valve.
- If there are any deposits adhering to the valve, clean the valve. When cleaning the valve, use diesel fuel or kerosene.
- Apply vacuum to the diaphragm of the swirl control valve and check that the valve opens and closes smoothly.
- If there are any deposits adhering to the valve, clean the valve.
|
|
||||
|
|
||||
| 13. REPAIR OR REPLACE VACUUM HOSE |
Repair or replace the vacuum hose.
|
|
||||
| 14. REPLACE INTAKE MANIFOLD |
Replace the intake manifold (swirl control valve).
|
|
||||
| 15. REPLACE VACUUM CONTROL VALVE SET |
Replace the vacuum control valve set.
- HINT:
- Before replacing the vacuum control valve set, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.
| NEXT | |
| 16. PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE) |
![]() ![]() |
Disconnect the vacuum hoses from the vacuum switching valve (for Swirl Control Valve).
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.
Check the VSV operation when it is operated using the GTS.
- OK:
GTS Operation
Specified Condition
VSV ON
Air from port E flows out through port F
VSV OFF
Air from port E flows out through air filter
Reconnect the vacuum hoses.
|
|
||||
|
|
||||
| 17. REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 18. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and MAF.
Take a snapshot when the engine speed is maintained at 4000 rpm with no load.
Read the values of "MAP" and "MAF" in the Data List using the snapshot review function.
- OK:
- MAF is 100 gm/sec. or more and MAP is 110 kPa or higher.
- HINT:
- The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
- The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.
- The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
| NEXT | ||
| ||

