2014-2019 Hiace · Service Manual ENGINE

P2009 Intake Manifold Runner Control Circuit Low (Bank 1)

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

Refer to DTC P2006 (Click here).
P2009 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
2 seconds after engine is started, race engine for 1 second
Open in vacuum switching valve assembly (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic).
  1. Vacuum switching valve assembly (for swirl control valve)
  2. Open in vacuum switching valve assembly (for swirl control valve) circuit
  3. ECM
P2010 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
2 seconds after engine is started, race engine for 1 second
Short in vacuum switching valve assembly (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic).
  1. Vacuum switching valve assembly (for swirl control valve)
  2. Short in vacuum switching valve assembly (for swirl control valve) circuit
  3. ECM

WIRING DIAGRAM

A321018E01

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
A067588E16
  1. Connect the GTS to the DLC3.

  1. Disconnect the vacuum hoses from the vacuum switching valve assembly (for swirl control valve).

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.

  1. Check the vacuum switching valve (for swirl control valve) operation when it is operated using the GTS.

    OK:
    GTS Operation
    Specified Condition
    VSV ON
    Air from port E flows out through port F
    VSV OFF
    Air from port E flows out through air filter

  1. Reconnect the vacuum hoses.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR SWIRL CONTROL VALVE) (RESISTANCE)
  1. Inspect the vacuum switching valve assembly (for swirl control valve) (Click here).



NG
Go to step 9
OK


3. INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR SWIRL CONTROL VALVE) (POWER SOURCE VOLTAGE)

  1. A249191E09
    Disconnect the vacuum switching valve assembly (for swirl control valve) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D67-2 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Vacuum Switching Valve Assembly (for Swirl Control Valve))

  1. Reconnect the vacuum switching valve assembly (for swirl control valve) connector.



NG
Go to step 6
OK


4. CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY (FOR SWIRL CONTROL VALVE) - ECM)
  1. Disconnect the vacuum switching valve assembly (for swirl control valve) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D67-1 - D134-42 (SCV)
    Always
    Below 1 Ω
    D67-1 or D134-42 (SCV) - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Reconnect the vacuum switching valve assembly (for swirl control valve) connector.

  1. Reconnect the ECM connector.



NG
Go to step 11
OK


5. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 12
6. CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY (FOR SWIRL CONTROL VALVE) - EFI NO. 2 RELAY)
  1. Remove the EFI NO. 2 relay from the engine room relay block No 1.

  1. Disconnect the vacuum switching valve assembly (for swirl control valve) connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    EFI NO. 2 relay terminal 5 - D67-2
    Always
    Below 1 Ω
    EFI NO. 2 relay terminal 5 or D67-2 - Body ground and other terminals
    Always
    10 kΩ or higher

  1. Reinstall the EFI NO. 2 relay.

  1. Reconnect the vacuum switching valve assembly (for swirl control valve) connector.



NG
Go to step 11
OK


7. INSPECT EFI NO. 2 RELAY
  1. Inspect the EFI NO. 2 relay (Click here).



NG
Go to step 10
OK


8. INSPECT ECM POWER SOURCE CIRCUIT
  1. Check the ECM power source circuit (Click here).



NEXT
Go to step 12
9. REPLACE VACUUM CONTROL VALVE SET
  1. Replace the vacuum control valve set (Click here).



NEXT
Go to step 12
10. REPLACE EFI NO. 2 RELAY
  1. Replace the EFI NO. 2 relay.



NEXT
Go to step 12
11. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace harness or connector.


NEXT


12. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Start the engine and wait for 2 seconds or more.

  1. Race the engine for 1 second.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P2006 Intake Manifold Runner Control Stuck Closed (Bank 1) (from Jan 2017)P200C Diesel Particulate Filter Temperature Too High Bank 1 (+ P200E, P2428) (from Jan 2017) →