2014-2019 Hiace · Service Manual BODY

1-2 Power Slide Door Sensor Malfunction

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION

When the door control relay assembly receives a jam signal from the power slide door sensor assembly or power slide door assembly RH*, the door control relay assembly stops closing the power slide door.
When the door control relay assembly determines the open circuit in the power slide door sensor assembly or power slide door sensor assembly RH* circuit, code 1-2 is output.
DTC No.
DTC Detection Condition
Trouble Area
1-2
  1. During self-diagnostic mode 1, open in power slide door sensor circuit is detected when power slide door is operated
  1. Power slide door sensor assembly
  2. Power slide door sensor assembly RH*
  3. No. 2 rear door wire
  4. Rear door wire RH*
  5. Door control relay assembly
  6. Harness or connector
  1. *: for RH Side, w/ Power Slide Door

WIRING DIAGRAM

(Click here)

INSPECTION PROCEDURE


1. CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTC (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (for LH Side)
    B
    DTC is output (for RH Side, w/ Power Slide Door)
    C



B
Go to step 3

C
Go to step 6
A

USE SIMULATION METHOD TO CHECK (Click here)

3. INSPECT POWER SLIDE DOOR SENSOR ASSEMBLY
  1. Remove the power slide door sensor assembly (Click here).

  1. Inspect the power slide door sensor assembly (Click here).



NG
REPLACE POWER SLIDE DOOR SENSOR ASSEMBLY (Click here)
OK


4. INSPECT NO. 2 REAR DOOR WIRE

  1. B365974E01
    Disconnect the oq1 and po2 No. 2 rear door wire connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-13 - B-10
    Always
    Below 1 Ω
    A-10 - B-16
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    No. 2 Rear Door Wire
    (Door Control Relay Assembly Side)
    *b
    No. 2 Rear Door Wire
    (Power Slide Door Sensor Assembly Side)



NG
REPLACE NO. 2 REAR DOOR WIRE (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (POWER SLIDE DOOR SENSOR ASSEMBLY - DOOR CONTROL RELAY ASSEMBLY)
  1. Disconnect the p6 power slide door sensor assembly connector.

  1. Disconnect the q4 door control relay assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    p6-1 - q4-14 (OS)
    Always
    Below 1 Ω
    p6-2 - q4-13 (OSG)
    Always
    Below 1 Ω
    p6-1 or q4-14 (OS) - Body ground
    Always
    10 kΩ or higher
    p6-2 or q4-13 (OSG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DOOR CONTROL RELAY ASSEMBLY (Click here)

6. INSPECT POWER SLIDE DOOR SENSOR ASSEMBLY RH
  1. Remove the power slide door sensor assembly RH (Click here).

  1. Inspect the power slide door sensor assembly RH (Click here).



NG
REPLACE POWER SLIDE DOOR SENSOR ASSEMBLY RH (Click here)
OK


7. INSPECT REAR DOOR WIRE RH

  1. B365974E01
    Disconnect the ci1 and fc1 rear door wire RH connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-13 - B-10
    Always
    Below 1 Ω
    A-10 - B-16
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear Door Wire RH
    (Door Control Relay Assembly Side)
    *b
    Rear Door Wire RH
    (Power Slide Door Sensor Assembly RH Side)



NG
REPLACE REAR DOOR WIRE RH (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (POWER SLIDE DOOR SENSOR ASSEMBLY RH - DOOR CONTROL RELAY ASSEMBLY)
  1. Disconnect the f6 power slide door sensor assembly RH connector.

  1. Disconnect the I4 door control relay assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    f6-1 - I4-14 (OS)
    Always
    Below 1 Ω
    f6-2 - I4-13 (OSG)
    Always
    Below 1 Ω
    f6-1 or I4-14 (OS) - Body ground
    Always
    10 kΩ or higher
    f6-2 or I4-13 (OSG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DOOR CONTROL RELAY ASSEMBLY (Click here)


← DIAGNOSTIC TROUBLE CODE CHART (from Jan 2017)1-2 Power Slide Door Sensor Malfunction (Jan 2015 – Dec 2016) →