1-2 Power Slide Door Sensor Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017
DESCRIPTION
When the door control relay assembly receives a jam signal from the power slide door sensor assembly or power slide door assembly RH*, the door control relay assembly stops closing the power slide door.When the door control relay assembly determines the open circuit in the power slide door sensor assembly or power slide door sensor assembly RH* circuit, code 1-2 is output.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| 1-2 |
|
|
- *: for RH Side, w/ Power Slide Door
WIRING DIAGRAM
(Click here)INSPECTION PROCEDURE
| 1. CLEAR DTC |
Clear the DTC (Click here).
| NEXT | |
| 2. CHECK FOR DTC |
Check for DTC (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output (for LH Side)
B
DTC is output (for RH Side, w/ Power Slide Door)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 3. INSPECT POWER SLIDE DOOR SENSOR ASSEMBLY |
Remove the power slide door sensor assembly (Click here).
Inspect the power slide door sensor assembly (Click here).
|
|
||||
| OK | |
| 4. INSPECT NO. 2 REAR DOOR WIRE |
Disconnect the oq1 and po2 No. 2 rear door wire connectors.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A-13 - B-10
Always
Below 1 Ω
A-10 - B-16
Always
Below 1 Ω
Text in Illustration *a
No. 2 Rear Door Wire
(Door Control Relay Assembly Side)
*b
No. 2 Rear Door Wire
(Power Slide Door Sensor Assembly Side)
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (POWER SLIDE DOOR SENSOR ASSEMBLY - DOOR CONTROL RELAY ASSEMBLY) |
Disconnect the p6 power slide door sensor assembly connector.
Disconnect the q4 door control relay assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
p6-1 - q4-14 (OS)
Always
Below 1 Ω
p6-2 - q4-13 (OSG)
Always
Below 1 Ω
p6-1 or q4-14 (OS) - Body ground
Always
10 kΩ or higher
p6-2 or q4-13 (OSG) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 6. INSPECT POWER SLIDE DOOR SENSOR ASSEMBLY RH |
Remove the power slide door sensor assembly RH (Click here).
Inspect the power slide door sensor assembly RH (Click here).
|
|
||||
| OK | |
| 7. INSPECT REAR DOOR WIRE RH |
Disconnect the ci1 and fc1 rear door wire RH connectors.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A-13 - B-10
Always
Below 1 Ω
A-10 - B-16
Always
Below 1 Ω
Text in Illustration *a
Rear Door Wire RH
(Door Control Relay Assembly Side)
*b
Rear Door Wire RH
(Power Slide Door Sensor Assembly RH Side)
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (POWER SLIDE DOOR SENSOR ASSEMBLY RH - DOOR CONTROL RELAY ASSEMBLY) |
Disconnect the f6 power slide door sensor assembly RH connector.
Disconnect the I4 door control relay assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
f6-1 - I4-14 (OS)
Always
Below 1 Ω
f6-2 - I4-13 (OSG)
Always
Below 1 Ω
f6-1 or I4-14 (OS) - Body ground
Always
10 kΩ or higher
f6-2 or I4-13 (OSG) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
