2014-2019 Hiace · Service Manual BRAKE

C1403 Rear Speed Sensor RH Malfunction

Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.
The speed sensor generates vehicle speed pulses based on the rotation of the skid control rotor. The skid control ECU (brake actuator assembly) detects the speed of each wheel using this vehicle speed pulse.

HINT:
When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.

C321041E01
Text in Illustration 
*1
Rear Speed Sensor
*2
Rear Skid Control Rotor
*a
Waveform (Reference):
Between Speed Sensor (-) and Body Ground
*b
Low speed
*c
High speed
-
-
DTC No.
DTC Detection Condition
Trouble Area
C1403
C1404
Either of the following is detected:
  1. At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.
  2. At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.
  3. At a vehicle speed less than 10 km/h (6 mph), outputs from both speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except both rear speed sensors are 0 km/h (0 mph))
  1. Rear speed sensor RH/LH
  2. Sensor installation
  3. Rear skid control rotor RH/LH

HINT:
  1. DTC C1403 is for the rear speed sensor RH.
  2. DTC C1404 is for the rear speed sensor LH.


WIRING DIAGRAM

C321038E01

INSPECTION PROCEDURE


1. CHECK REAR SPEED SENSOR INSTALLATION
  1. Turn the ignition switch off.

  1. C168336E13
    Check the speed sensor installation (Click here).

    OK:
    There is no clearance between the sensor and the rear axle housing.
    The installation bolt is tightened properly.

    Text in Illustration 
    *a
    Normal
    *b
    Abnormal
    *c
    Clearance



NG
INSTALL REAR SPEED SENSOR CORRECTLY (Click here)
OK


2. INSPECT REAR SPEED SENSOR TIP
  1. Remove the rear speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil, or foreign matter on the sensor tip.

    NOTICE:
    1. If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
    2. If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.
    3. Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


3. INSPECT REAR SKID CONTROL ROTOR
  1. Remove the rear axle shaft with backing plate (Click here).

  1. Check the rear skid control rotor.

    OK:
    No scratches, oil or foreign matter on the rotor.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).

  1. Reinstall the rear speed sensor and the rear axle shaft with backing plate (Click here for speed sensor, Click here for rear axle shaft with backing plate).



NG
CLEAN OR REPLACE REAR SKID CONTROL ROTOR
OK


4. READ VALUE USING GTS (REAR SPEED SENSOR)
  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    RL Wheel Speed
    Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
Go to step 5
OK

USE SIMULATION METHOD TO CHECK (Click here)

5. REPLACE REAR SPEED SENSOR
  1. Turn the ignition switch off.

  1. Replace the rear speed sensor (Click here).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


6. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTCs C1401 and C1402 are not output
    A
    DTCs C1401 and/or C1402 are output
    B

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



B
REPLACE REAR SKID CONTROL ROTOR (Click here)
A

END


← C1401 Front Speed Sensor RH Malfunction (+ C1402) (from Dec 2017)C1403 Rear Speed Sensor RH Malfunction (+ C1404) (Apr 2016 – Dec 2016) →