C1401 Front Speed Sensor RH Malfunction
Diagnostic trouble codes · Vehicles built from Dec 2017
Also covers:
- C1402 Front Speed Sensor LH Malfunction
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.The speed sensor generates vehicle speed pulses based on the rotation of the skid control rotor. The skid control ECU (brake actuator assembly) detects the speed of each wheel using this vehicle speed pulse.
- HINT:
- When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


| *1 |
Front Speed Sensor |
*2 |
Front Skid Control Rotor |
| *a |
Waveform (Reference): Between Speed Sensor (-) and Body Ground |
*b |
Low speed |
| *c |
High speed |
- |
- |
| DTC No. |
DTC Detection Condition |
Trouble Area |
| C1401 C1402 |
Either of the following is detected:
|
|
- HINT:
- DTC C1401 is for the front speed sensor RH.
- DTC C1402 is for the front speed sensor LH.
- DTC C1401 is for the front speed sensor RH.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FRONT SPEED SENSOR INSTALLATION |
Turn the ignition switch off.
Check the speed sensor installation (Click here).

- OK:
- There is no clearance between the sensor and the front steering knuckle.
- The installation bolt is tightened properly.
Text in Illustration *a
Normal
*b
Abnormal
*c
Clearance
|
|
||||
| OK | |
| 2. INSPECT FRONT SPEED SENSOR TIP |
Remove the front speed sensor (Click here).
Check the speed sensor tip.
- OK:
- No scratches, oil, or foreign matter on the sensor tip.
- NOTICE:
- If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
- If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.
- Check the speed sensor signal after cleaning or replacement (Click here).
- If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
|
|
||||
| OK | |
| 3. INSPECT FRONT SKID CONTROL ROTOR |
Remove the front skid control rotor (Click here).
Check the front skid control rotor.
- OK:
- No scratches, oil or foreign matter on the rotor.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
Reinstall the front speed sensor and the front skid control rotor (Click here for speed sensor, Click here for skid control rotor).
|
|
||||
| OK | |
| 4. READ VALUE USING GTS (FRONT SPEED SENSOR) |
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Wheel Speed
Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
FL Wheel Speed
Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
- HINT:
- If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
| OK | ||
| ||
| 5. REPLACE FRONT SPEED SENSOR |
Turn the ignition switch off.
Replace the front speed sensor (Click here).
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 6. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
- Result:
Result
Proceed to
DTCs C1401 and C1402 are not output
A
DTCs C1401 and/or C1402 are output
B
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| A | ||
| ||
