2014-2019 Hiace · Service Manual COMMUNICATION SYSTEM

ECM Communication Stop Mode

Circuit diagnosis · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

Detection Item
Symptom
Trouble Area
ECM Communication Stop Mode
Either condition is met:
  1. "ECM (Engine)" is not displayed on "Bus Check".
  2. "ECM Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside ECM
  2. ECM

WIRING DIAGRAM

C299902E06
C299902E05
C299903E01
C299903E04
C299903E03

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
  1. Disconnect the ECM connectors.

C234869E14
Text in Illustration 
*A
for 1KD-FTV (w/ DPF)
*B
for 1KD-FTV (w/o DPF)
*C
for 2KD-FTV
*D
for 1TR-FE, 2TR-FE
*E
for 5L-E
-
-
*a
Front view of wire harness connector
(to ECM)
-
-
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1KD-FTV (w/ DPF) 
    Tester Connection
    Condition
    Specified Condition
    B73-32 (EC) - Body ground
    Always
    Below 1 Ω
    D99-44 (E02) - Body ground
    Always
    Below 1 Ω
    D99-45 (E01) - Body ground
    Always
    Below 1 Ω
    D99-109 (E1) - Body ground
    Always
    Below 1 Ω
    for 1KD-FTV (w/o DPF) 
    Tester Connection
    Condition
    Specified Condition
    B72-32 (EC) - Body ground
    Always
    Below 1 Ω
    D98-44 (E02) - Body ground
    Always
    Below 1 Ω
    D98-45 (E01) - Body ground
    Always
    Below 1 Ω
    D98-109 (E1) - Body ground
    Always
    Below 1 Ω
    for 2KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    B88-32 (EC) - Body ground
    Always
    Below 1 Ω
    D105-44 (E02) - Body ground
    Always
    Below 1 Ω
    D105-45 (E01) - Body ground
    Always
    Below 1 Ω
    D105-109 (E1) - Body ground
    Always
    Below 1 Ω
    for 1TR-FE, 2TR-FE 
    Tester Connection
    Condition
    Specified Condition
    B71-32 (EC) - Body ground
    Always
    Below 1 Ω
    D97-45 (E02) - Body ground
    Always
    Below 1 Ω
    D97-46 (E01) - Body ground
    Always
    Below 1 Ω
    D97-105 (E1) - Body ground
    Always
    Below 1 Ω
    for 5L-E 
    Tester Connection
    Condition
    Specified Condition
    B74-50 (EC) - Body ground
    Always
    Below 1 Ω
    D100-44 (E02) - Body ground
    Always
    Below 1 Ω
    D100-45 (E01) - Body ground
    Always
    Below 1 Ω
    D100-109 (E1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 1KD-FTV (w/ DPF) 
    Tester Connection
    Condition
    Specified Condition
    B73-2 (BATT) - Body ground
    Always
    11 to 14 V
    B73-1 (+B) - Body ground
    Battery positive (+) voltage applied to terminal B73-45 (MREL)
    11 to 14 V
    B73-20 (+B2) - Body ground
    Battery positive (+) voltage applied to terminal B73-45 (MREL)
    11 to 14 V
    B73-25 (IGSW) - Body ground
    Ignition switch ON
    11 to 14 V
    for 1KD-FTV (w/o DPF) 
    Tester Connection
    Condition
    Specified Condition
    B72-2 (BATT) - Body ground
    Always
    11 to 14 V
    B72-1 (+B) - Body ground
    Battery positive (+) voltage applied to terminal B72-45 (MREL)
    11 to 14 V
    B72-20 (+B2) - Body ground
    Battery positive (+) voltage applied to terminal B72-45 (MREL)
    11 to 14 V
    B72-25 (IGSW) - Body ground
    Ignition switch ON
    11 to 14 V
    for 2KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    B88-2 (BATT) - Body ground
    Always
    11 to 14 V
    B88-1 (+B) - Body ground
    Battery positive (+) voltage applied to terminal B88-28 (MREL)
    11 to 14 V
    B88-25 (IGSW) - Body ground
    Ignition switch ON
    11 to 14 V
    for 1TR-FE, 2TR-FE 
    Tester Connection
    Condition
    Specified Condition
    B71-20 (BATT) - Body ground
    Always
    11 to 14 V
    B71-2 (+B) - Body ground
    Battery positive (+) voltage applied to terminal B71-44 (MREL)
    11 to 14 V
    B71-27 (IGSW) - Body ground
    Ignition switch ON
    11 to 14 V
    for 5L-E 
    Tester Connection
    Condition
    Specified Condition
    B74-2 (BATT) - Body ground
    Always
    11 to 14 V
    B74-1 (+B) - Body ground
    Battery positive (+) voltage applied to terminal B74-5 (MREL)
    11 to 14 V
    B74-25 (IGSW) - Body ground
    Ignition switch ON
    11 to 14 V

    HINT:
    *: Replacement procedure:

    1. for 1KD-FTV (Click here).
    2. for 2KD-FTV (Click here).
    3. for 1TR-FE (Click here).
    4. for 2TR-FE (Click here).
    5. for 5L-E (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM*


← Steering Angle Sensor Communication Stop Mode (from Jan 2017)ECM Communication Stop Mode (Jan 2015 – Mar 2016) →