2014-2019 Hiace · Service Manual COMMUNICATION SYSTEM

ECM Communication Stop Mode

Circuit diagnosis · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

Detection Item
Symptom
Trouble Area
ECM Communication Stop Mode
Either condition is met:
  1. "ECM (Engine)" is not displayed on "Bus Check".
  2. "ECM Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside ECM
  2. ECM

WIRING DIAGRAM

C299902E06
C299902E05
C299903E01
C299902E07
C299903E05
C299903E03

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

  1. for 1KD-FTV (w/ DPF)

    1. Disconnect the ECM connectors.C234869E15

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to ECM)
      -
      -

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      B73-32 (EC) - Body ground
      Always
      Below 1 Ω
      D99-44 (E02) - Body ground
      Always
      Below 1 Ω
      D99-45 (E01) - Body ground
      Always
      Below 1 Ω
      D99-109 (E1) - Body ground
      Always
      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      B73-2 (BATT) - Body ground
      Always
      11 to 14 V
      B73-1 (+B) - Body ground
      Battery positive (+) voltage applied to terminal B73-45 (MREL)
      11 to 14 V
      B73-20 (+B2) - Body ground
      Battery positive (+) voltage applied to terminal B73-45 (MREL)
      11 to 14 V
      B73-25 (IGSW) - Body ground
      Ignition switch ON
      11 to 14 V

  1. for 1KD-FTV (w/o DPF)

    1. Disconnect the ECM connectors.C234869E16

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to ECM)
      -
      -

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      B72-32 (EC) - Body ground
      Always
      Below 1 Ω
      D98-44 (E02) - Body ground
      Always
      Below 1 Ω
      D98-45 (E01) - Body ground
      Always
      Below 1 Ω
      D98-109 (E1) - Body ground
      Always
      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      B72-2 (BATT) - Body ground
      Always
      11 to 14 V
      B72-1 (+B) - Body ground
      Battery positive (+) voltage applied to terminal B72-45 (MREL)
      11 to 14 V
      B72-20 (+B2) - Body ground
      Battery positive (+) voltage applied to terminal B72-45 (MREL)
      11 to 14 V
      B72-25 (IGSW) - Body ground
      Ignition switch ON
      11 to 14 V

  1. for 2KD-FTV

    1. Disconnect the ECM connectors.C234869E17

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to ECM)
      -
      -

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      B88-32 (EC) - Body ground
      Always
      Below 1 Ω
      D105-44 (E02) - Body ground
      Always
      Below 1 Ω
      D105-45 (E01) - Body ground
      Always
      Below 1 Ω
      D105-109 (E1) - Body ground
      Always
      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      B88-2 (BATT) - Body ground
      Always
      11 to 14 V
      B88-1 (+B) - Body ground
      Battery positive (+) voltage applied to terminal B88-28 (MREL)
      11 to 14 V
      B88-25 (IGSW) - Body ground
      Ignition switch ON
      11 to 14 V

  1. for 1TR-FE, 2TR-FE (w/ Dual VVT-i)

    1. Disconnect the ECM connectors.C229008E09

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to ECM)
      -
      -

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      B94-32 (EC) - Body ground
      Always
      Below 1 Ω
      D116-58 (E02) - Body ground
      Always
      Below 1 Ω
      D116-57 (E01) - Body ground
      Always
      Below 1 Ω
      D116-59 (E1) - Body ground
      Always
      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      B94-1 (BATT) - Body ground
      Always
      11 to 14 V
      B94-2 (+B) - Body ground
      Battery positive (+) voltage applied to terminal B94-46 (MREL)
      11 to 14 V
      B94-3 (+B2) - Body ground
      Battery positive (+) voltage applied to terminal B94-46 (MREL)
      11 to 14 V
      B94-6 (IGSW) - Body ground
      Ignition switch ON
      11 to 14 V

  1. for 2TR-FE (w/o Dual VVT-i)

    1. Disconnect the ECM connectors.C234869E18

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to ECM)
      -
      -

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      B71-32 (EC) - Body ground
      Always
      Below 1 Ω
      D97-45 (E02) - Body ground
      Always
      Below 1 Ω
      D97-46 (E01) - Body ground
      Always
      Below 1 Ω
      D97-105 (E1) - Body ground
      Always
      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      B71-20 (BATT) - Body ground
      Always
      11 to 14 V
      B71-2 (+B) - Body ground
      Battery positive (+) voltage applied to terminal B71-44 (MREL)
      11 to 14 V
      B71-27 (IGSW) - Body ground
      Ignition switch ON
      11 to 14 V

  1. for 5L-E

    1. Disconnect the ECM connectors.C234869E19

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to ECM)
      -
      -

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      B74-50 (EC) - Body ground
      Always
      Below 1 Ω
      D100-44 (E02) - Body ground
      Always
      Below 1 Ω
      D100-45 (E01) - Body ground
      Always
      Below 1 Ω
      D100-109 (E1) - Body ground
      Always
      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      B74-2 (BATT) - Body ground
      Always
      11 to 14 V
      B74-1 (+B) - Body ground
      Battery positive (+) voltage applied to terminal B74-5 (MREL)
      11 to 14 V
      B74-25 (IGSW) - Body ground
      Ignition switch ON
      11 to 14 V

HINT:
*: Replacement procedure:

  1. for 1KD-FTV (Click here).
  2. for 2KD-FTV (Click here).
  3. for 1TR-FE (Click here).
  4. for 2TR-FE (w/o Dual VVT-i) (Click here).
  5. for 2TR-FE (w/ Dual VVT-i) (Click here).
  6. for 5L-E (Click here).


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM*


← ECM Communication Stop Mode (Oct 2014 – Dec 2014)ECM Communication Stop Mode (Apr 2016 – Dec 2016) →