ECM Communication Stop Mode
Circuit diagnosis · Vehicles built from Jan 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
| Detection Item |
Symptom |
Trouble Area |
| ECM Communication Stop Mode |
Either condition is met:
|
|
WIRING DIAGRAM














INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND) |
for 1KD-FTV (w/ DPF)
Disconnect the ECM connectors.


Text in Illustration *a
Front view of wire harness connector
(to ECM)
-
-
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B73-32 (EC) - Body ground
Always
Below 1 Ω
D99-44 (E02) - Body ground
Always
Below 1 Ω
D99-45 (E01) - Body ground
Always
Below 1 Ω
D99-109 (E1) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B73-2 (BATT) - Body ground
Always
11 to 14 V
B73-1 (+B) - Body ground
Battery positive (+) voltage applied to terminal B73-45 (MREL)
11 to 14 V
B73-20 (+B2) - Body ground
Battery positive (+) voltage applied to terminal B73-45 (MREL)
11 to 14 V
B73-25 (IGSW) - Body ground
Ignition switch ON
11 to 14 V
for 1KD-FTV (w/o DPF)
Disconnect the ECM connectors.


Text in Illustration *a
Front view of wire harness connector
(to ECM)
-
-
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B72-32 (EC) - Body ground
Always
Below 1 Ω
D98-44 (E02) - Body ground
Always
Below 1 Ω
D98-45 (E01) - Body ground
Always
Below 1 Ω
D98-109 (E1) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B72-2 (BATT) - Body ground
Always
11 to 14 V
B72-1 (+B) - Body ground
Battery positive (+) voltage applied to terminal B72-45 (MREL)
11 to 14 V
B72-20 (+B2) - Body ground
Battery positive (+) voltage applied to terminal B72-45 (MREL)
11 to 14 V
B72-25 (IGSW) - Body ground
Ignition switch ON
11 to 14 V
for 2KD-FTV
Disconnect the ECM connectors.


Text in Illustration *a
Front view of wire harness connector
(to ECM)
-
-
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B88-32 (EC) - Body ground
Always
Below 1 Ω
D105-44 (E02) - Body ground
Always
Below 1 Ω
D105-45 (E01) - Body ground
Always
Below 1 Ω
D105-109 (E1) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B88-2 (BATT) - Body ground
Always
11 to 14 V
B88-1 (+B) - Body ground
Battery positive (+) voltage applied to terminal B88-28 (MREL)
11 to 14 V
B88-25 (IGSW) - Body ground
Ignition switch ON
11 to 14 V
for 1GD-FTV
Disconnect the ECM connectors.


Text in Illustration *a
Front view of wire harness connector
(to ECM)
-
-
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B97-14 (EC) - Body ground
Always
Below 1 Ω
D134-21 (E1) - Body ground
Always
Below 1 Ω
D134-51 (E01) - Body ground
Always
Below 1 Ω
D134-52 (E02) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B97-1 (BATT) - Body ground
Always
11 to 14 V
B97-2 (+B) - Body ground
Battery positive (+) voltage applied to terminal B97-46 (MREL)
11 to 14 V
B97-3 (+B2) - Body ground
Battery positive (+) voltage applied to terminal B97-46 (MREL)
11 to 14 V
B97-6 (IGSW) - Body ground
Ignition switch ON
11 to 14 V
for 1TR-FE, 2TR-FE (w/ Dual VVT-i)
Disconnect the ECM connectors.


Text in Illustration *a
Front view of wire harness connector
(to ECM)
-
-
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B94-32 (EC) - Body ground
Always
Below 1 Ω
D116-58 (E02) - Body ground
Always
Below 1 Ω
D116-57 (E01) - Body ground
Always
Below 1 Ω
D116-59 (E1) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B94-1 (BATT) - Body ground
Always
11 to 14 V
B94-2 (+B) - Body ground
Battery positive (+) voltage applied to terminal B94-46 (MREL)
11 to 14 V
B94-3 (+B2) - Body ground
Battery positive (+) voltage applied to terminal B94-46 (MREL)
11 to 14 V
B94-6 (IGSW) - Body ground
Ignition switch ON
11 to 14 V
for 2TR-FE (w/o Dual VVT-i)
Disconnect the ECM connectors.


Text in Illustration *a
Front view of wire harness connector
(to ECM)
-
-
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B71-32 (EC) - Body ground
Always
Below 1 Ω
D97-45 (E02) - Body ground
Always
Below 1 Ω
D97-46 (E01) - Body ground
Always
Below 1 Ω
D97-105 (E1) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B71-20 (BATT) - Body ground
Always
11 to 14 V
B71-2 (+B) - Body ground
Battery positive (+) voltage applied to terminal B71-44 (MREL)
11 to 14 V
B71-27 (IGSW) - Body ground
Ignition switch ON
11 to 14 V
for 5L-E
Disconnect the ECM connectors.


Text in Illustration *a
Front view of wire harness connector
(to ECM)
-
-
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B74-50 (EC) - Body ground
Always
Below 1 Ω
D100-44 (E02) - Body ground
Always
Below 1 Ω
D100-45 (E01) - Body ground
Always
Below 1 Ω
D100-109 (E1) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B74-2 (BATT) - Body ground
Always
11 to 14 V
B74-1 (+B) - Body ground
Battery positive (+) voltage applied to terminal B74-5 (MREL)
11 to 14 V
B74-25 (IGSW) - Body ground
Ignition switch ON
11 to 14 V
- HINT:
- *: Replacement procedure:
- for 1KD-FTV (Click here).
- for 2KD-FTV (Click here).
- for 1GD-FTV (Click here).
- for 1TR-FE (Click here).
- for 2TR-FE (w/o Dual VVT-i) (Click here).
- for 2TR-FE (w/ Dual VVT-i) (Click here).
- for 5L-E (Click here).
|
|
||||
| OK | ||
| ||
