Refer to DTC P200C4B (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P200C4B).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P20CF00 | Exhaust Aftertreatment Fuel Injector "A" Stuck Open | AF (O2) Lambda B1S1 is less than 0.85 for a certain time while the engine is running (1 trip detection logic). | ·
Open or short in exhaust fuel addition injector assembly circuit ·
Exhaust fuel addition injector assembly ·
Fuel filter element assembly Common Inspection Item: ·
Fuel injection system ·
Intake/Exhaust system ·
After treatment control system |
Comes on | DTC stored | SAE Code: P20CF |
| DTC No. | Data List |
|---|---|
| P20CF00 | ·
A/F (O2) Lambda B1S1 ·
Exhaust Temperature B1S2 ·
Exhaust Temperature B1S3 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P20CF00 | PM forced regeneration |
The ECM monitors the air fuel ratio to detect whether the exhaust fuel addition injector assembly is stuck open.
If the air fuel ratio becomes too rich, the ECM determines that the exhaust fuel addition injector assembly is stuck open, illuminates the MIL and limits engine output.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION).
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P20CF00 is output | A |
| DTC P20CF00 and other DTCs are output | B |
When DTC P20CF00 and following DTCs are output, uncombusted fuel adhesion to the air fuel ratio sensor due to air fuel ratio sensor malfunction, fuel leaks, insufficient combustion due to parts malfunction (intake, exhaust or injection system), or an exhaust fuel addition injector assembly wiring malfunction is suspected as a cause. Therefore, diagnose the following DTCs first.
DTCs for the air fuel ratio sensor are DTC P223711, P223712, P223713, P223716, P223717, P225111 and P225112.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P223711
A DTC for fuel leakage is DTC P009300.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P009300
DTCs for the exhaust fuel addition injector assembly wiring malfunction are DTC P20CB12 and P20CB14.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P20CB12
A DTC for EGR valve flow malfunction is DTC P040000.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P040000
A DTC for EGR valve stuck open is DTC P040371.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P040371
A
B
If a fuel odor is noted from the white smoke during the inspection, fuel leaks from the exhaust fuel addition injector assembly are suspected.
Disconnect the cable from the negative (-) battery terminal or remove the EFI-MAIN fuse from the No. 1 engine room relay block and junction block assembly for more than 1 minute.
Start the engine and race it to 3000 rpm several times.
Check for white smoke in the exhaust gas. If found, check for a fuel odor or the smell of burning oil.
| Result | Proceed to |
|---|---|
| White smoke and a fuel odor are present. | A |
| White smoke and a smell of burning oil are present. | B |
| Except above | C |
A
B
C
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / A/F (O2) Lambda B1S1 and Exhaust Temperature B1S3.
| Tester Display |
|---|
| A/F (O2) Lambda B1S1 |
| Exhaust Temperature B1S3 |
Drive the vehicle until the value of Exhaust Temperature B1S3 becomes 300°C (572°F) or more to activate the air fuel ratio sensors.
Activation of the air fuel ratio sensor can be checked by confirming whether the value of A/F (O2) Lambda B1S1 has changed from 1.99.
Check that there is no problem on driving performance such as hesitation, knocking, rough idling, insufficient power and acceleration stumbling, or white smoke in emissions.
The air fuel ratio sensor does not operate until the vehicle has been driven for a period of time with an exhaust gas temperature of 200°C (392°F) or more.
Perform diagnosis when the air fuel ratio sensor is operating and active.
Normal condition in the illustration is only an example. "A/F (O2) Lambda B1S1" changes depending on driving conditions. If it changes at the range more than 1.0, it is normal.
| Result | Proceed to |
|---|---|
| There is no problem with driving performance such as hesitation, knocking, rough idling, insufficient power or acceleration stumbling, but excessive white smoke is present in the exhaust gas | A |
| Except above | B |
If white smoke is present in the exhaust gas without any driving performance problems such as hesitation, knocking, rough idling, insufficient power or acceleration stumbling, fuel injected due to a malfunction in the exhaust fuel addition injector assembly is the suspected cause of the white smoke.
A
B
Replace the exhaust fuel addition injector assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clean the fuel filter case and replace the fuel filter element assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT
Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).
Perform PM forced regeneration.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
PM forced regeneration completes normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform inspection and repair of relevant DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for oil leaks and white smoke from the turbocharger sub-assembly and perform any necessary repairs.
Other than a malfunction of the turbocharger sub-assembly, exhaust valve stem oil leaks are suspected.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).
Perform PM forced regeneration.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
PM forced regeneration completes normally.
| Proceed to |
|---|
| NEXT |
NEXT
Check the fuel injection system.
| Proceed to |
|---|
| NEXT |
NEXT
Check the intake/exhaust system.
| Proceed to |
|---|
| NEXT |
NEXT
Check the after treatment control system.
| Proceed to |
|---|
| NEXT |
NEXT