Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › MONOLITHIC CONVERTER (w/ DPF) › 2019.02–2019.06
RM35X0E _51 Engine / Hybrid System _079220 1GD-FTV EMISSION CONTROL _0384163 MONOLITHIC CONVERTER(w/ DPF) A

1GD-FTV EMISSION CONTROL  MONOLITHIC CONVERTER(w/ DPF)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the monolithic converter removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of exhaust manifold converter sub-assembly Clear DPF thermal deterioration data -
·

w/ DPF:

(Click here)

·

w/ Urea SCR System:

(Click here)



CAUTION:
A343692

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


PROCEDURE

Hide 17410 2.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 17168 3.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17751 4.REMOVE NO. 1 AIR CLEANER INLET

Hide 17705 5.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE

Hide 17801 6.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 25733A 10.REMOVE NO. 1 VACUUM PIPE

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440895

Remove the nut and clamp from the No. 1 vacuum pipe and No. 2 vacuum pipe.


b.
A440896

Using a 17 mm union nut wrench, remove the No. 1 vacuum pipe from the exhaust manifold converter sub-assembly.


Hide 25734 11.REMOVE NO. 2 VACUUM PIPE

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440897

Using a 17 mm union nut wrench, remove the No. 2 vacuum pipe from the exhaust manifold converter sub-assembly.


b.
A440898

Remove the clamp from the pipe clamp.


Hide 17578B 12.REMOVE PIPE CLAMP

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440899

Remove the 3 bolts and pipe clamp from the engine cover bracket.


Hide 12631A 13.REMOVE ENGINE COVER BRACKET

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A444703

Detach the 2 clamp and disconnect the engine wire from the engine cover bracket.


b.
A440900

Remove the 2 bolts and engine cover bracket from the cylinder head sub-assembly.


Hide 14.DISCONNECT INTERMEDIATE SHAFT ASSEMBLY (for RHD)

Hide 17167 16.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440901

Remove the 3 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.


Hide 17271 17.REMOVE NO. 1 TURBO INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440902

Remove the 3 bolts and No. 1 turbo insulator from the exhaust manifold and turbocharger sub-assembly.


Hide 17118 18.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440904

Remove the bolt, 2 nuts and No. 2 exhaust pipe support stay from the cylinder block sub-assembly and exhaust manifold converter sub-assembly.


Hide 17118 19.REMOVE EXHAUST PIPE SUPPORT STAY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440905

Remove the 3 bolts and exhaust pipe support stay from the cylinder block sub-assembly and exhaust manifold converter sub-assembly.


Hide 25051 20.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440906

Remove the nut, exhaust pipe clamp and exhaust manifold converter sub-assembly from the turbocharger sub-assembly.


b.

Remove the gasket.