Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › EGR COOLER › 2019.02–2019.06
RM35X0E _51 Engine / Hybrid System _079220 1GD-FTV EMISSION CONTROL _0384172 EGR COOLER A

1GD-FTV EMISSION CONTROL  EGR COOLER  INSTALLATION  


PROCEDURE

Hide 25681 1.INSTALL NO. 1 EGR COOLER

a.

Install a new gasket and the No. 1 EGR cooler to the No. 2 EGR valve assembly with electric EGR control valve assembly with the 4 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 2.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.
A442617C02
0.135,0.156 0.448,0.313 0.313,0.156 10 true *A 0.198,2.531 0.51,2.688 0.313,0.156 10 true *B 0.771,0.396 0.948,0.552 0.177,0.156 10 true 4 3.073,1.729 3.25,1.885 0.177,0.156 10 true 3 1.906,2.021 2.083,2.177 0.177,0.156 10 true 2 1.406,2.021 1.583,2.177 0.177,0.156 10 true 1 0.771,2.802 0.948,2.958 0.177,0.156 10 true 4 3.094,4.146 3.271,4.302 0.177,0.156 10 true 3 1.99,4.427 2.167,4.583 0.177,0.156 10 true 2 1.406,4.438 1.583,4.594 0.177,0.156 10 true 1
*A for Single Actuator EGR Valve Assembly
*B for Double Actuator EGR Valve Assembly


Temporarily install the No. 1 EGR cooler and No. 2 EGR valve assembly with electric EGR control valve assembly to the intake manifold with the 4 bolts.


b.

Tighten the 4 bolts in the order shown in the illustration.

HINT:

Make sure to tighten the bolts in the order.


Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 25601 3.CONNECT EGR PIPE WITH COOLER SUB-ASSEMBLY (for Double Actuator EGR Bypass Valve)

Hide 25601 4.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (for Single Actuator EGR Bypass Valve)

Hide 16209 5.CONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16206B 6.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install the No. 3 water by-pass pipe sub-assembly to the No. 1 EGR cooler with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 9 water by-pass hose to the electric EGR control valve assembly, and slide the clamp to secure the hose.


c.

Connect the No. 8 water by-pass hose to the No. 3 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.


d.

Attach the clamp and connect the No. 4 fuel hose to the No. 3 water by-pass pipe sub-assembly.


Hide 89421C 14.INSTALL DIESEL TURBO PRESSURE SENSOR

Hide 87209 16.INSTALL WATER HOSE SUB-ASSEMBLY (w/ Heater)

Hide 26100G 17.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 55701J 18.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 85110 19.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

Hide 20.ADD ENGINE COOLANT