Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF)
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0385516 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P064C9E  Glow Plug Control Module 1 Stuck On  P066B19  Cylinder 1 Glow Plug Control Circuit High Circuit Current Above Threshold  P066D19  Cylinder 2 Glow Plug Control Circuit High Circuit Current Above Threshold  P066F19  Cylinder 3 Glow Plug Control Circuit High Circuit Current Above Threshold  P067116  Cylinder 1 Glow Plug Circuit/Open Circuit Voltage Below Threshold  P067216  Cylinder 2 Glow Plug Circuit/Open Circuit Voltage Below Threshold  P067316  Cylinder 3 Glow Plug Circuit/Open Circuit Voltage Below Threshold  P067416  Cylinder 4 Glow Plug Circuit/Open Circuit Voltage Below Threshold  P067B19  Cylinder 4 Glow Plug Control Circuit High Circuit Current Above Threshold  P166F2B  Glow Plug Control Module 1 Signal Cross Coupled  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P064C9E Glow Plug Control Module 1 Stuck On The MOS inside the glow plug control unit is detected as being stuck on 3 times while the glow plug assemblies are on (2 trip detection logic). Glow plug controller Comes on DTC stored SAE Code: P064C
P066B19 Cylinder 1 Glow Plug Control Circuit High Circuit Current Above Threshold A short circuit in the No. 1 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 1 glow plug assembly

·

Short in No. 1 glow plug assembly circuit


Comes on DTC stored SAE Code: P066B
P066D19 Cylinder 2 Glow Plug Control Circuit High Circuit Current Above Threshold A short circuit in the No. 2 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 2 glow plug assembly

·

Short in No. 2 glow plug assembly circuit


Comes on DTC stored SAE Code: P066D
P066F19 Cylinder 3 Glow Plug Control Circuit High Circuit Current Above Threshold A short circuit in the No. 3 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 3 glow plug assembly

·

Short in No. 3 glow plug assembly circuit


Comes on DTC stored SAE Code: P066F
P067116 Cylinder 1 Glow Plug Circuit/Open Circuit Voltage Below Threshold An open circuit in the No. 1 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 1 glow plug assembly

·

Open in No. 1 glow plug assembly circuit

·

GLOW relay


Comes on DTC stored SAE Code: P0671
P067216 Cylinder 2 Glow Plug Circuit/Open Circuit Voltage Below Threshold An open circuit in the No. 2 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 2 glow plug assembly

·

Open in No. 2 glow plug assembly circuit

·

GLOW relay


Comes on DTC stored SAE Code: P0672
P067316 Cylinder 3 Glow Plug Circuit/Open Circuit Voltage Below Threshold An open circuit in the No. 3 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 3 glow plug assembly

·

Open in No. 3 glow plug assembly circuit

·

GLOW relay


Comes on DTC stored SAE Code: P0673
P067416 Cylinder 4 Glow Plug Circuit/Open Circuit Voltage Below Threshold An open circuit in the No. 4 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 4 glow plug assembly

·

Open in No. 4 glow plug assembly circuit

·

GLOW relay


Comes on DTC stored SAE Code: P0674
P067B19 Cylinder 4 Glow Plug Control Circuit High Circuit Current Above Threshold A short circuit in the No. 4 glow plug assembly circuit is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

No. 4 glow plug assembly

·

Short in No. 4 glow plug assembly circuit


Comes on DTC stored SAE Code: P067B
P166F2B Glow Plug Control Module 1 Signal Cross Coupled A short circuit in a wire harness between the glow plug assemblies is detected 3 times while the glow plug assemblies are on (2 trip detection logic).
·

Glow plug controller

·

Short in glow plug assembly circuit


Comes on DTC stored SAE Code: P166F

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P064C9E
P066B19
P066D19
P066F19
P067116
P067216
P067316
P067416
P067B19
P166F2B
Enter check mode

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the DTCs.

Result:
Result Proceed to
DTC P067116, P067216, P067316 and/or P067416 is output A
DTC P066B19, P066D19, P066F19 and/or P067B19 is output B
DTC P064C9E and/or P166F2B is output C




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF GLOW PLUG CONTROLLER)

B

14.CHECK HARNESS AND CONNECTOR

C

19.CHECK HARNESS AND CONNECTOR
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF GLOW PLUG CONTROLLER)
a.
A241159C27
0.646,1.115 1.063,1.417 0.417,0.302 1.927,1.719 1.76,1.24 true 0.167,0.219 0.479,0.417 0.313,0.198 10 false *a 0.74,1.188 1.052,1.385 0.313,0.198 10 false A29 1.979,1.656 2.594,1.854 0.615,0.198 10 false BATT
*a Front view of wire harness connector
(to Glow Plug Controller)


Disconnect the glow plug controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A29-1 (BATT) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR

NG

8.INSPECT GLOW RELAY
3.CHECK HARNESS AND CONNECTOR
a.

Disconnect connectors of the glow plug controller.

A348991C32
2.573,1.26 3.031,1.563 0.458,0.302 4.823,1.219 5.281,1.521 0.458,0.302 1.167,2.583 1.5,2.26 1.5,2.26 1.625,2.26 true 1.438,1.917 1.771,1.594 1.771,1.594 1.896,1.594 true 1.74,1.25 2.073,0.927 2.073,0.927 2.198,0.927 true 2.021,0.573 2.354,0.25 2.354,0.25 2.479,0.25 true 3.729,1.438 3.917,1.896 true 6.021,1.49 6.208,1.948 true 3.438,1.479 3.188,1.948 true 5.677,1.479 5.427,1.948 true 1.094,0.344 1.406,0.542 0.313,0.198 10 false *1 2.552,0.188 2.865,0.385 0.313,0.198 10 false 4 2.271,0.854 2.583,1.052 0.313,0.198 10 false 3 1.969,1.5 2.281,1.698 0.313,0.198 10 false 2 1.698,2.198 2.01,2.396 0.313,0.198 10 false 1 2.677,1.323 2.99,1.521 0.313,0.198 10 false A31 4.917,1.292 5.292,1.521 0.375,0.229 10 false A30 4.948,0.813 5.26,1.01 0.313,0.198 10 false *b 2.917,0.667 3.229,0.865 0.313,0.198 10 false *a 3.063,1.958 3.479,2.167 0.417,0.208 10 false GL1 3.823,1.948 4.323,2.177 0.5,0.229 10 false GL2 5.208,1.958 5.521,2.156 0.313,0.198 10 false GL3 6.188,1.969 6.5,2.167 0.313,0.198 10 false GL4
*1 No. 1 Glow Plug Connector - -
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)



b.

Remove the No. 1 glow plug connector from the glow plug assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A31-1 (GL1) - No. 1 glow plug connector terminal 1 Always Below 1 Ω
A31-2 (GL2) - No. 1 glow plug connector terminal 2 Always Below 1 Ω
A30-1 (GL3) - No. 1 glow plug connector terminal 3 Always Below 1 Ω
A30-2 (GL4) - No. 1 glow plug connector terminal 4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT GLOW PLUG ASSEMBLY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.INSPECT GLOW PLUG ASSEMBLY
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Exchange the glow plug assemblies of the malfunctioning cylinders (the cylinders indicated by output DTCs) with the glow plug assemblies of normally functioning cylinders.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 372 1

f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

g.

Read the DTCs.

Result:
Result Proceed to
Same DTCs (that have been cleared) A
Other DTCs B


HINT:

Check for DTCs in check mode.




A

20.REPLACE GLOW PLUG CONTROLLER

B

5.REPLACE GLOW PLUG ASSEMBLY
5.REPLACE GLOW PLUG ASSEMBLY
a.

Replace the glow plug assembly.

Click hereEngine / Hybrid System>1GD-FTV (STARTING)>GLOW PLUG>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 372 1

g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Confirm that the DTC is not output again.

HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END

8.INSPECT GLOW RELAY

Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR

NG

13.REPLACE GLOW RELAY
9.CHECK HARNESS AND CONNECTOR
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Remove the GLOW relay from the No. 1 engine room relay block and junction block assembly.


d.

Disconnect connectors of the glow plug controller.


e.

Disconnect the ECM connectors.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GLOW relay terminal 5 - Battery positive terminal Always Below 1 Ω
GLOW relay terminal 3 - A29-1 (BATT) Always Below 1 Ω
GLOW relay terminal 2 - N2-19 (GREL) Always Below 1 Ω
GLOW relay terminal 5 or Battery positive terminal - Body ground and other terminals Always 10 kΩ or higher
GLOW relay terminal 3 or A29-1 (BATT) - Body ground and other terminals Always 10 kΩ or higher
GLOW relay terminal 2 or N2-19 (GREL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.CHECK HARNESS AND CONNECTOR
a.

Remove the EFI MAIN relay and GLOW relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GLOW relay terminal 1 - EFI MAIN relay terminal 5 Always Below 1 Ω
GLOW relay terminal 1 - EFI MAIN relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

GO TO ECM POWER SOURCE CIRCUIT

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.REPLACE GLOW RELAY
a.

Replace the GLOW relay.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CHECK HARNESS AND CONNECTOR
a.

Disconnect connectors of the glow plug controller.

A348991C32
2.573,1.26 3.031,1.563 0.458,0.302 4.823,1.219 5.281,1.521 0.458,0.302 1.167,2.583 1.5,2.26 1.5,2.26 1.625,2.26 true 1.438,1.917 1.771,1.594 1.771,1.594 1.896,1.594 true 1.74,1.25 2.073,0.927 2.073,0.927 2.198,0.927 true 2.021,0.573 2.354,0.25 2.354,0.25 2.479,0.25 true 3.729,1.438 3.917,1.896 true 6.021,1.49 6.208,1.948 true 3.438,1.479 3.188,1.948 true 5.677,1.479 5.427,1.948 true 1.094,0.344 1.406,0.542 0.313,0.198 10 false *1 2.552,0.188 2.865,0.385 0.313,0.198 10 false 4 2.271,0.854 2.583,1.052 0.313,0.198 10 false 3 1.969,1.5 2.281,1.698 0.313,0.198 10 false 2 1.698,2.198 2.01,2.396 0.313,0.198 10 false 1 2.677,1.323 2.99,1.521 0.313,0.198 10 false A31 4.917,1.292 5.292,1.521 0.375,0.229 10 false A30 4.948,0.813 5.26,1.01 0.313,0.198 10 false *b 2.917,0.667 3.229,0.865 0.313,0.198 10 false *a 3.063,1.958 3.479,2.167 0.417,0.208 10 false GL1 3.823,1.948 4.323,2.177 0.5,0.229 10 false GL2 5.208,1.958 5.521,2.156 0.313,0.198 10 false GL3 6.188,1.969 6.5,2.167 0.313,0.198 10 false GL4
*1 No. 1 Glow Plug Connector - -
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)



b.

Remove the No. 1 glow plug connector from the glow plug assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A31-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground Always 10 kΩ or higher
A31-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground Always 10 kΩ or higher
A30-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground Always 10 kΩ or higher
A30-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



Result:
Proceed to
OK
NG



OK

15.REPLACE GLOW PLUG CONTROLLER

NG

16.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.REPLACE GLOW PLUG CONTROLLER
a.

Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 372 1

g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Read the DTCs.

OK:

No DTC is output.


HINT:

Check for DTCs in check mode.



Result:
Proceed to
OK
NG



OK

END

NG

18.REPLACE GLOW PLUG ASSEMBLY
18.REPLACE GLOW PLUG ASSEMBLY
a.

Replace the glow plug assembly.

Click hereEngine / Hybrid System>1GD-FTV (STARTING)>GLOW PLUG>REMOVAL


Result:
Proceed to
NEXT



NEXT

22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
19.CHECK HARNESS AND CONNECTOR
a.

Disconnect connectors of the glow plug controller.

A348991C32
2.573,1.26 3.031,1.563 0.458,0.302 4.823,1.219 5.281,1.521 0.458,0.302 1.167,2.583 1.5,2.26 1.5,2.26 1.625,2.26 true 1.438,1.917 1.771,1.594 1.771,1.594 1.896,1.594 true 1.74,1.25 2.073,0.927 2.073,0.927 2.198,0.927 true 2.021,0.573 2.354,0.25 2.354,0.25 2.479,0.25 true 3.729,1.438 3.917,1.896 true 6.021,1.49 6.208,1.948 true 3.438,1.479 3.188,1.948 true 5.677,1.479 5.427,1.948 true 1.094,0.344 1.406,0.542 0.313,0.198 10 false *1 2.552,0.188 2.865,0.385 0.313,0.198 10 false 4 2.271,0.854 2.583,1.052 0.313,0.198 10 false 3 1.969,1.5 2.281,1.698 0.313,0.198 10 false 2 1.698,2.198 2.01,2.396 0.313,0.198 10 false 1 2.677,1.323 2.99,1.521 0.313,0.198 10 false A31 4.917,1.292 5.292,1.521 0.375,0.229 10 false A30 4.948,0.813 5.26,1.01 0.313,0.198 10 false *b 2.917,0.667 3.229,0.865 0.313,0.198 10 false *a 3.063,1.958 3.479,2.167 0.417,0.208 10 false GL1 3.823,1.948 4.323,2.177 0.5,0.229 10 false GL2 5.208,1.958 5.521,2.156 0.313,0.198 10 false GL3 6.188,1.969 6.5,2.167 0.313,0.198 10 false GL4
*1 No. 1 Glow Plug Connector - -
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)



b.

Remove the No. 1 glow plug connector from the glow plug assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A31-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground Always 10 kΩ or higher
A31-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground Always 10 kΩ or higher
A30-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground Always 10 kΩ or higher
A30-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



Result:
Proceed to
OK
NG



OK

20.REPLACE GLOW PLUG CONTROLLER

NG

21.REPAIR OR REPLACE HARNESS OR CONNECTOR
20.REPLACE GLOW PLUG CONTROLLER
a.

Result:
Proceed to
NEXT



NEXT

22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
21.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 372 1

g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Confirm that the DTC is not output again.

HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END