Refer to DTC P200C4B
For more information on the exhaust fuel addition injector assembly and DPF catalyst, refer to the following procedures.
If DTC P20CB12 or P20CB14 is present, refer to the DTC table for Diesel Particulate Filter System.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P20CB12 | Exhaust Aftertreatment Fuel Injector "A" Circuit Short to Battery | Short in exhaust fuel addition injector assembly circuit for 3 seconds (1 trip detection logic). | ·
Short in exhaust fuel addition injector assembly circuit ·
Exhaust fuel addition injector assembly ·
ECM |
Class B2 | DTC stored | SAE Code: P20CE |
| P20CB14 | Exhaust Aftertreatment Fuel Injector "A" Circuit Short to Ground or Open | Open or short in exhaust fuel addition injector assembly circuit for 3 seconds (1 trip detection logic). | ·
Open or short in exhaust fuel addition injector assembly circuit ·
Exhaust fuel addition injector assembly ·
ECM |
Class B2 | DTC stored | SAE Code: P20CD |
| DTC No. | Data List |
|---|---|
| P20CB12
P20CB14 |
·
Fuel Injection Valve + Output Signal Bank 1 ·
Fuel Injection Valve - Output Signal Bank 1 |
DTC P200C4B, P200E4B, P20CF00 and/or P24284B will be present if there is an open malfunction in the exhaust fuel addition injector assembly circuit.
The ECM monitors the FIV+ terminal (Fuel Injection Valve + Output Signal Bank 1) and FIV- terminal (Fuel Injection Valve - Output Signal Bank 1) of the fuel addition injector assembly.
When a malfunction is detected in the monitor signal while the fuel addition injector assembly is operating or not operating, P20CB12 or P20CB14 is stored.
| Fuel Addition Injector Assembly Operation Status | FIV+ Terminal | FIV- Terminal |
|---|---|---|
| (Fuel Injection Valve + Output Signal Bank 1) | (Fuel Injection Valve - Output Signal Bank 1) | |
| Not operating | ON | OFF |
| Operating | ON | ON |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P20CB12
P20CB14 |
PM forced regeneration |
Inspect the fuses of circuits related to this system before performing the following procedure.
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the exhaust fuel addition injector assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the exhaust fuel addition injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E78-2 (+B) - E8-1 (FIV+) | Always | Below 1 Ω |
| E78-1 (FIV) - E7-3 (FIV-) | Always | Below 1 Ω |
| E78-2 (+B) or E8-1 (FIV+) - Body ground and other terminals | Always | 10 kΩ or higher |
| E78-1 (FIV) or E7-3 (FIV-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the exhaust fuel addition injector assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off for 30 seconds or more.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Perform PM forced regeneration.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT