Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  Rough Idling or Excessive Engine Vibrations  


DESCRIPTION

Malfunction Condition Main Trouble Area Related Trouble Area
Rough idling or juddering due to abnormal combustion Injector assembly malfunctions
·

Injector sliding malfunction

·

Injector stuck closed

·

Injector stuck open

·

Deposits in injector

·

Injector circuit malfunction


·

Injector compensation code

·

Fuel leak

·

Engine mounting

·

Intake system leakage

·

Intake system blockage

·

EGR system

·

Throttle valve system

·

Mass air flow meter sub-assembly

·

Fuel supply pump assembly (pre-stroke control valve)

·

Fuel pressure sensor

·

Low quality fuel

·

Vehicle modifications

·

Fuel filter element assembly air bleed problem

·

Accessory problem (A/C, generator, etc.)

·

ECM



HINT:
·

This troubleshooting procedure checks for the cause of rough idling and excessive engine vibrations.

·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List result values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.

·

Check that the vehicle has not been modified in any way prior to the vehicle inspection.



Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Mass Air Flow Meter Sub-assembly
Main fault Decrease in performance (foreign matter is stuck)
Symptoms Lack of power, black smoke
Data List Mass Air Flow Sensor
HINT:

The maximum fuel injection volume is controlled according to the output from the mass air flow meter sub-assembly.



Glow System
Main fault Glow system malfunction
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Diagnostic Point
·

Measure the resistance of the glow plug assembly

·

Check the glow plug indicator light



Engine
Main fault Loss of compression
Symptoms Rough idle (lack of power always)
Data List Engine Speed Cylinder
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.


Injection Feedback Value
·

When an Injector Feedback Value is more than 5 mm3/st, there may be a malfunction in the corresponding cylinder.




b.

Diesel Injection

Fuel Supply Pump Assembly
Main fault -
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Pressure (High), Target Fuel Pressure (High)
·

Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High) during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).

·

If the fuel pressure is 20000 kPag below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPag, then idling will be rough.


HINT:

The fuel pressure changes at engine start, but is approx. 25000 kPag at engine start after the engine is warmed up.


Diagnostic Trouble Code Even if Fuel Pressure (High) is below Target Fuel Pressure (High), a DTC will not be stored.

Fuel Filter Element Assembly
Main fault Blockage
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Pressure (High), Target Fuel Pressure (High)
·

Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High) during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).

·

If the fuel pressure is 20000 kPag below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPag, then idling will be rough.


HINT:

The fuel pressure changes at engine start, but is approx. 25000 kPag at engine start after the engine is warmed up.


Diagnostic Trouble Code Even if Fuel Pressure (High) is below Target Fuel Pressure (High), a DTC will not be stored.

Injector Assembly
Main fault Blockage
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Value
·

When an Injector Feedback Value is more than 5 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.



Fuel Pressure Sensor
Main fault Open circuit, decrease in performance (foreign matter is stuck)
Symptoms Difficult to start, rough idle, engine stall, lack of power
Data List Fuel Pressure (High), Target Fuel Pressure (High)
·

Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Fuel Pressure (High) follows Target Fuel Pressure (High). If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Fuel Pressure (High) decreases to a value less than Target Fuel Pressure (High)).


Diagnostic Trouble Code When the fuel pressure sensor has a fault, some DTCs may be stored.

Irregular Fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)


c.

Diesel EGR

EGR System
Main fault
·

Does not move smoothly

·

Does not close completely


Symptoms
·

Rough idle

·

EGR valve stuck closed: A loud turbocharger sound.

·

EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).


Data List Actual EGR Valve Position No.1, Target EGR Valve Position No.1
·

Generally, Actual EGR Valve Position No.1 = Target EGR Valve Position No.1 +/-5% (fully closed: 0%, fully open: 100%).

·

Using the EGR valve Active Test, check whether Actual EGR Valve Position No.1 follows Target EGR Valve Position No.1 (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).

·

EGR valve is fully closed when the engine switch is turned on (IG) (engine stopped).

·

EGR valve opens to the halfway point at idling after the engine is warmed up.


EGR Close Learning Value Bank 1
·

When leaving the vehicle idling, the normal range of EGR Close Learning Value Bank 1 is 0 to 1 V.

·

In cases when EGR Close Learning Value Bank 1 is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.




d.

Diesel Throttle

Diesel Throttle System
Main fault Stuck, does not move smoothly
Symptoms
·

Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.

·

Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.


Data List EGR Close Learning Value Bank 1
·

0%: Fully closed

·

100%: Fully open

·

When the engine switch is turned on (IG) (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the engine switch is turned from on (IG) to off, the throttle is fully closed temporarily.





Data List Related to Rough Idling


HINT:

Depending on the vehicle model, the applicable Data List items may vary. Data List items other than the ones used in the diagnostic procedure are for reference only.

·

Engine Speed

·

Mass Air Flow Sensor

·

Intake Air Temperature

·

Coolant Temperature

·

Engine Speed Cylinder #1 to #4

(Output only when the "Check the Cylinder Compression" Active Test is performed)

·

Target Fuel Pressure (High)

·

Fuel Pressure (High)

·

Injection Feedback Value #1 to #4

·

Target Injection Volume

·

Actual Throttle Position Bank 1

·

Target EGR Valve Position No.1

·

Actual EGR Valve Position No.1

·

EGR Close Learning Value Bank 1




Vehicle Control History Freeze Frame Data Items Related to Rough Idling


HINT:

The frequency of the malfunction can be determined by confirming the number of times the symptom occurred.

·

Rough Idle Count (Plural Cylinders)

·

Rough Idle Count (Compression Leakage)

·

Rough Idle Count #1

·

Rough Idle Count #2

·

Rough Idle Count #3

·

Rough Idle Count #4




CAUTION / NOTICE / HINT

NOTICE:

After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION).


HINT:
·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Make sure to reproduce the conditions present when the malfunction occurred.

·

Using the GTS, read the Data List to confirm the engine operating conditions. This information can be useful when troubleshooting.

·

The vehicle condition when the problem symptoms occurred can be determined using the Vehicle Control History.

·

As the Vehicle Control History data may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.

·

If the problem symptoms do not recur, attempt to reproduce the symptoms and conditions when the malfunction occurred based on the result of the customer problem analysis and Vehicle Control History. Place the priority on confirming the symptoms.

·

When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.

·

The suspected cause of the problem symptoms can be determined using the codes, items, and Freeze Frame Data within the Vehicle Control History.

·

When confirming the Freeze Frame Data, be sure to check all multi Freeze Frame Data.

·

When confirming the Freeze Frame Data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.

·

If the malfunction is currently occurring, use the Data List to confirm the current vehicle condition. By using the Data List, more detailed vehicle information can be confirmed than by using Vehicle Control History Freeze Frame Data by itself.

·

As Vehicle Control History may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History before returning the vehicle to the customer.



PROCEDURE

1.CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT
a.

Check the wire harness and connector connections of common rail system components.

OK:

The wire harnesses and connectors are connected securely.


HINT:

The engine may have problems when there is an intermittent disconnection in a circuit related to the fuel pressure sensor, crankshaft position sensor, engine coolant temperature sensor, etc.



Result:
Proceed to
OK
NG



OK

2.READ OUTPUT DTC (RELATING TO ENGINE)

NG

21.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.READ OUTPUT DTC (RELATING TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

d.

Read the pending DTCs.

Result:
Result Proceed to
No DTCs are output A
Engine related DTCs are output B




A

3.READ VEHICLE CONTROL HISTORY FREEZE FRAME DATA

B

3.READ VEHICLE CONTROL HISTORY FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and Transmission / Utility / Vehicle Control History (RoB).

Powertrain > Engine and Transmission > Utility
Tester Display
Vehicle Control History (RoB)
50005 456 55
HINT:

It is also possible to display Vehicle Control History during the Health Check, if "Store All Data" is selected.



e.

Confirm if any data relating to the problem symptoms exist in the Vehicle Control History.

HINT:
·

The vehicle condition when the problem symptoms occurred can be determined by confirming the Vehicle Control History Freeze Frame Data.

·

As the Vehicle Control History data may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.

·

Using information from the customer about when the problem symptom occurred, find the Freeze Frame Data with the appropriate Key Cycle, Total Distance Traveled, etc., to find vehicle history that may be related to the problem symptoms.




f.

Check the vehicle control history code and freeze frame data.

Result:
Vehicle Control History Vehicle Control History Freeze Frame Data Suspected Area Proceed to
Only Rough Idle #1, #2, #3 or #4 is stored
(Vehicle Control History Code: X0821 to X0824)
The vehicle control history code matches a cylinder with an Injection Feedback Value that exceeds 5.0 mm3/st.
HINT:

When there are temporary changes in the injection characteristics, the malfunction may not be indicated by the value for Injection Feedback Value in the freeze frame data.


A specific cylinder is malfunctioning:

Injector assembly


A
- - D
Rough Idle (Plural Cylinders) is stored
(Vehicle Control History Code: X082A)
When EGR Rate Differential (Actual-Target) increases by more than 30%, there may be a malfunction in the EGR system. Multiple cylinders are malfunctioning:
·

EGR system


B
When there is data stored that indicates that Fuel Pressure (High) is low compared to Target Fuel Pressure (High), there may be a malfunction in the fuel pressure control system, such as in the fuel supply pump assembly. Multiple cylinders are malfunctioning:
·

Fuel supply pump assembly

·

Low-quality fuel


C
When data indicating that Intake Manifold Absolute Pressure is low (50 kPa or less) is stored, there may be a stuck closed malfunction in the diesel throttle system or EGR valve. Multiple cylinders are malfunctioning:
·

EGR system

·

Diesel throttle system


-
Rough Idle (Compression Leakage) is stored
(Vehicle Control History Code: X082D)
- - D
The malfunction is not currently occurring and there is no Vehicle Control History related to the problem symptoms stated by the customer. D




D

4.TAKE SNAPSHOT DURING IDLING (PROCEDURE 4)

A

8.INSPECT INJECTOR COMPENSATION CODE

B

24.CHECK FOR DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)

C

15.INSPECT CLOGGED FUEL PIPE
4.TAKE SNAPSHOT DURING IDLING (PROCEDURE 4)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


d.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Diesel Rough Idle.


e.

Take a snapshot when idling with no load after the engine is warmed up and when the problem is occurring.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.

·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.

·

If rough idling occurs when the A/C switch is on, take another snapshot with the A/C switch on.

·

Take a snapshot when the problem is occurring, such as when the engine is cold. However, if the problem does not reoccur, it is acceptable to only take a snapshot after the engine is warmed up.




Result:
Proceed to
NEXT



NEXT

5.CHECK WHITE SMOKE
5.CHECK WHITE SMOKE
a.

Start the engine.


b.

Fully depress the accelerator pedal, and then release it.


c.

Check whether white smoke is emitted when racing the engine.

NOTICE:

Be sure not to check for white smoke indoors.


HINT:

Depending on whether there is oil mixed with the fuel, or whether there is unburned fuel present, the smell of the exhaust gas differs. When oil is mixed in, the exhaust gas smells such as burning oil.


Result:
Result Proceed to
White smoke is not emitted A
White smoke is emitted B




A

6.CHECK DATA LIST (ENGINE SPEED)

B

22.CHECK AND REPAIR ENGINE ASSEMBLY
6.CHECK DATA LIST (ENGINE SPEED)
a.

Check engine speed in the snapshot taken in procedure 4 when the engine was idling.

Result:
Result Proceed to
Change in engine speed coincides with air conditioning system operation B
Except above A




A

7.CHECK DATA LIST (INJECTION FEEDBACK VALUE #1 TO #4)

B

18.CHECK AIR CONDITIONING SYSTEM
7.CHECK DATA LIST (INJECTION FEEDBACK VALUE #1 TO #4)
a.

Check Injection Feedback Value #1 to #4 in the snapshot taken in procedure 4 when the engine was idling.

Result:
Result Proceed to
Injection Feedback Value for at least one cylinder is more than +5 mm3/st and engine vibration is abnormally large A
Except above B


HINT:
·

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Value to increase.

·

The ECM controls the system so that the sum of Injection Feedback Value for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Value for a cylinder is less than -5.0 mm3/st, as long as the value of Injection Feedback Value for each of the other cylinders is 5.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

8.INSPECT INJECTOR COMPENSATION CODE

B

14.CHECK DATA LIST (TARGET FUEL PRESSURE (HIGH) AND FUEL PRESSURE (HIGH))
8.INSPECT INJECTOR COMPENSATION CODE
a.

Read the injector compensation code.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION

Powertrain > Engine and Transmission > Utility
Tester Display
Injector Compensation
50005 456 4596
OK:

Compensation codes stored in the ECM match compensation codes of the installed injector assemblies.



Result:
Proceed to
OK
NG



OK

9.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)

NG

13.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
9.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Active Test / Control the Select Cylinder Fuel Cut.

Powertrain > Engine and Transmission > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 456 42007
HINT:
·

If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

10.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
10.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

11.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
11.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

12.BLEED AIR FROM FUEL SYSTEM
12.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

13.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
13.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation code.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION

Powertrain > Engine and Transmission > Utility
Tester Display
Injector Compensation
50005 456 4596

b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION

Powertrain > Engine and Transmission > Utility
Tester Display
Pilot Quantity Learning
50005 456 4569

Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CHECK DATA LIST (TARGET FUEL PRESSURE (HIGH) AND FUEL PRESSURE (HIGH))
a.

Check engine speed in the snapshot taken in procedure 5 when the engine was idling after having been warmed up.

Result:
Result Proceed to
Difference between Target Fuel Pressure (High) and Fuel Pressure (High) is 5000 kPag (51.0 kgf/cm2, 725 psi) or more A
Except above B




A

15.INSPECT CLOGGED FUEL PIPE

B

23.CHECK DATA LIST (EGR RATE DIFFERENTIAL (ACTUAL-TARGET))
15.INSPECT CLOGGED FUEL PIPE
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Target Fuel Pressure (High) and Fuel Pressure (High).

Powertrain > Engine and Transmission > Data List
Tester Display
Target Fuel Pressure (High)
Fuel Pressure (High)
50003 456 307,308

d.

With no load after the engine is warmed up, take a snapshot when idling and vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.


e.

Check the Target Fuel Pressure (High) and Fuel Pressure (High).

A261221E32
0.031,1.708 1.365,2.083 1.333,0.375 10 false Target Fuel Pressure (High) 3.844,2.125 6.427,2.271 2.583,0.146 10 false Normal Fuel Pressure (High) 3.708,0.344 5.969,0.542 2.26,0.198 10 false Abnormal Fuel Pressure (High)*1 0.104,0.031 2.635,0.198 2.531,0.167 10 false Fuel Pressure (High) During Idling 1.083,2.406 3.75,2.75 2.667,0.344 10 false Pressure varies periodically with a period of approximately 2 seconds or more 5.906,1.115 7.156,1.896 1.25,0.781 10 false Normal Condition: +/-5000 kPag (Idling after Engine Warmed Up)

Result:
Result Proceed to
While idling the vehicle, "Fuel Pressure (High)" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1 A
"Fuel Pressure (High)" is normal while idling the vehicle, but "Fuel Pressure (High)" does not follow "Target Fuel Pressure (High)" when the accelerator pedal is fully depressed in 2nd gear*2
Except above B


NOTICE:
·

*1: The cause may be a squashed or blocked fuel pipe or hose.

·

*2: The cause may be a clogged fuel filter element assembly.





A

16.REPAIR OR REPLACE CLOGGED FUEL LINE

B

19.REPLACE FUEL SUPPLY PUMP ASSEMBLY
16.REPAIR OR REPLACE CLOGGED FUEL LINE
a.

Repair or replace the clogged (including frozen fuel) fuel pipe.


b.

Replace the fuel filter element assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT

HINT:

If "Fuel Pressure (High)" does not follow "Target Fuel Pressure (High)" when the accelerator pedal is fully depressed in 2nd gear, replace the fuel filter element assembly.



Result:
Proceed to
NEXT



NEXT

17.BLEED AIR FROM FUEL SYSTEM
17.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
18.CHECK AIR CONDITIONING SYSTEM
a.

Check the air conditioning system.

HINT:
·

Be sure to check the air conditioning hoses and pipes.




Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
19.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

20.BLEED AIR FROM FUEL SYSTEM
20.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
21.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
22.CHECK AND REPAIR ENGINE ASSEMBLY
a.

Check the following items and repair the malfunctioning part if necessary.

i.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION



Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
23.CHECK DATA LIST (EGR RATE DIFFERENTIAL (ACTUAL-TARGET))
a.

Check EGR Rate Differential (Actual-Target) in the snapshot taken in procedure 4 when the engine was idling.


Result:
Result Proceed to
EGR Rate Differential (Actual-Target) of +30% or more is displayed A
Except above B



A

24.CHECK FOR DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)

B

25.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE BANK 1)
24.CHECK FOR DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
a.

Remove the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>REMOVAL


b.

Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.

NOTICE:
·

When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.

·

Do not forcibly open the valve, as it may be damaged or deformed.

·

When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.

·

When cleaning the electric EGR control valve assembly, care should be taken to prevent the ingress of cleaning solvent into the bearings of the valve shaft, and when wiping off deposits on the EGR valve, care should be taken not to push the deposits into the bearings of the valve shaft. These contaminants may adversely affect the function of the EGR valve.

·

When cleaning the electric EGR control valve assembly, perform the initialization procedure.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION



HINT:
·

If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.

·

If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power. In this case, clean the electric EGR control valve assembly.




c.

Reinstall the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>INSTALLATION


Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
25.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE BANK 1)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


c.

Turn the engine switch off. Wait for 30 seconds, and then restart the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Mass Air Flow Sensor.

Powertrain > Engine and Transmission > Data List
Tester Display
Mass Air Flow Sensor
50003 456 242

f.

Read the Mass Air Flow Sensor value displayed on the GTS while the engine is idling.


g.

Enter the following menus: Powertrain / Engine and Transmission / Active Test / Activate the EGR Valve Close Bank 1 / Data List / Mass Air Flow Sensor.

Powertrain > Engine and Transmission > Active Test
Active Test Display
Activate the EGR Valve Close Bank 1
Data List Display
Mass Air Flow Sensor
50004 456 2 242

h.

Read the Mass Air Flow Sensor value when the EGR valve is closed using the Active Test function.

HINT:
·

If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.

·

Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.



Result:
Active Test Result Proceed to
Activate the EGR Valve Close Bank 1:
OFF to Close
Mass Air Flow Sensor value does not change A
Mass Air Flow Sensor value changes B


NOTICE:

As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.


HINT:

The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric EGR control valve assembly or mass air flow meter sub-assembly.


Reference:
EGR Valve Condition (Opening) Measuring Condition Mass Air Flow Sensor (Reference)
Open (41%)
·

Atmospheric pressure: 101 kPa

·

Engine coolant temperature: 75°C (167°F)


3 to 7 gm/sec
Closed (0%) 10 to 21 gm/sec




A

24.CHECK FOR DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)

B

26.PERFORM PILOT QUANTITY LEARNING (DETAIL)
26.PERFORM PILOT QUANTITY LEARNING (DETAIL)
a.

Perform the pilot quantity learning (detail).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION

Powertrain > Engine and Transmission > Utility
Tester Display
Pilot Quantity Learning (Detail)
50005 456 4570

Result:
Proceed to
NEXT



NEXT

27.CHECK ROUGH IDLING OR EXCESSIVE ENGINE VIBRATIONS
27.CHECK ROUGH IDLING OR EXCESSIVE ENGINE VIBRATIONS
a.

Check rough idling or excessive engine vibrations.

Result:
Result Proceed to
Rough idling or excessive engine vibrations do not occur A
Except above B




A

END

B

28.CHECK AND REPLACE ENGINE MOUNTING INSULATOR
28.CHECK AND REPLACE ENGINE MOUNTING INSULATOR
a.

Check the following items and repair or replace the malfunctioning part if necessary.

i.

Check that the engine mounting insulators are installed correctly.


ii.

Check that the engine mounting insulators are not twisted.


iii.

Check that deformation of an engine mounting insulator is not causing the engine to contact the vehicle body.



Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END