Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  P245900  Particulate Filter Regeneration Frequency Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P245900 Particulate Filter Regeneration Frequency Bank 1 The threshold at which catalyst differential pressure feedback causes automatic regeneration has been reached earlier and the regeneration interval has become shorter.
(2 trip detection logic)
·

Exhaust manifold converter sub-assembly

·

Differential pressure sensor assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Class B2 DTC stored SAE Code: P2459

MONITOR DESCRIPTION

When it is detected that the threshold at which catalyst differential pressure feedback causes automatic regeneration has been reached earlier and the regeneration interval has become shorter, P245900 is stored.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P245900 Drive the vehicle until the PM accumulation ratio reaches 20% or more.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the exhaust manifold converter sub-assembly (DPF catalyst), clear the thermal deterioration data stored in the ECM.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION

·

After the engine switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.READ DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.


d.

Record the stored DTC and freeze frame data.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

e.

Check Exhaust Fuel Addition F/B Bank 1 and Catalyst Differential Pressure Bank 1 in the freeze frame data.

HINT:
·

When the "Exhaust Fuel Addition F/B Bank 1" value is 1.45 or more, it indicates a high possibility of insufficient temperature increase during PM forced regeneration.

·

When the Catalyst Differential Pressure Bank 1 value is more than 0.27, it indicates a high possibility that DPF catalyst is clogged.




Result:
Proceed to
NEXT



NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P245900)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P245900)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and Transmission > Trouble Codes
50001 456
Result:
Result Proceed to
DTC P245900 is output A
DTC P245900 and P246300 is output B
DTC P245900 and P244B00 is output C




A

3.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)

B

C

3.READ VALUE USING GTS (PARTICULATE FILTER DIFFERENTIAL PRESSURE BANK 1)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Diesel Exhaust / Particulate Filter Differential Pressure Bank 1.

Powertrain > Engine and Transmission > Data List
Tester Display
Particulate Filter Differential Pressure Bank 1
50003 456 344

d.

Check the "Particulate Filter Differential Pressure Bank 1" values from idle speed to unloaded maximum engine speed.

Result:
Result Proceed to
"Particulate Filter Differential Pressure Bank 1" increases as engine speed increases from idle speed A
Except above B


A241154E10
3.313,3.375 3.542,3.375 3.542,3.375 3.719,3.875 false 4.25,4.281 4.125,4.281 false 4.125,4.281 3.854,3.979 false 4.146,4.927 4.042,4.927 4.042,4.927 3.833,4.76 false 0.469,1.479 1.74,1.865 1.271,0.385 10 false Engine Speed (rpm) 0.698,2.99 1.75,3.406 1.052,0.417 10 false Mass Air Flow Sensor (gm/sec) 0.625,4.125 1.698,4.854 1.073,0.729 10 false Particulate Filter Differential Pressure Bank 1 (kPa) 4.198,4.854 4.323,5 0.125,0.146 10 false A 1.771,1.875 1.875,2.156 0.104,0.281 10 false 0 1.781,3.24 1.885,3.521 0.104,0.281 10 false 0 1.792,4.615 1.896,4.896 0.104,0.281 10 false 0 0.677,0.854 1.948,1.24 1.271,0.385 10 false Unloaded Maximum Engine Speed 2.385,3.281 3.344,3.521 0.958,0.24 10 false Normal Piping 4.313,4.208 5.271,4.448 0.958,0.24 10 false Clogged Piping 2.313,5.417 5.333,5.698 3.021,0.281 10 false Negative pressure occurs for approx. 1 second.

HINT:

If Particulate Filter Differential Pressure Bank 1 indicates negative pressure for approx. 1 second as shown in the illustration (A) when the engine speed increases, the differential pressure sensor piping of the DPF catalyst may be clogged.




A

5.CHECK FOR BLACK SMOKE

B

4.CLEAN OR REPLACE AIR HOSE
4.CLEAN OR REPLACE AIR HOSE
a.

Even though it has been determined that the vacuum transmitting hose assembly needs to be repaired or cleaned, make sure to perform all diagnostic procedures for DTC P245900 before repairing or cleaning it.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR BLACK SMOKE
5.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the procedure [A] 10 times [B].


e.

Check for black smoke emission during the procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESSURE BANK 1)

NG

8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
6.READ VALUE USING GTS (CATALYST DIFFERENTIAL PRESSURE BANK 1)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Diesel Exhaust / Catalyst Differential Pressure Bank 1.

Powertrain > Engine and Transmission > Data List
Tester Display
Catalyst Differential Pressure Bank 1
50003 456 88

d.

Check the value of "Catalyst Differential Pressure Bank 1" at 4000 rpm without load.

Result:
Result Proceed to
"Catalyst Differential Pressure Bank 1" is more than 0.16 A
Except above B




A

8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

B

7.PERFORM PM FORCED REGENERATION
7.PERFORM PM FORCED REGENERATION
a.

Clear the DTC and "Exhaust Fuel Addition FB Bank 1" value by disconnecting the cable from the negative (-) battery terminal or removing the EFI-MAIN fuse for 1 minute or more.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

e.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


f.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

Result:

PM forced regeneration completes normally.



Result:
Proceed to
OK
NG



OK

END

NG

9.CHECK FUEL INJECTION SYSTEM
8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

Even though it has been determined that the exhaust manifold converter sub-assembly needs to be replaced, make sure to perform all diagnostic procedures for DTC P245900 before replacing it.


Result:
Proceed to
NEXT



NEXT

9.CHECK FUEL INJECTION SYSTEM
9.CHECK FUEL INJECTION SYSTEM

NEXT

10.CHECK INTAKE / EXHAUST SYSTEM
10.CHECK INTAKE / EXHAUST SYSTEM

NEXT

11.CHECK AFTER TREATMENT CONTROL SYSTEM
11.CHECK AFTER TREATMENT CONTROL SYSTEM

NEXT

12.REPAIR OR REPLACE MALFUNCTIONING PARTS
12.REPAIR OR REPLACE MALFUNCTIONING PARTS
HINT:

Repair, replace or clean the following items only when it has been determined necessary based on diagnosis for DTC P245900.


a.

Clean and/or repair the hoses of the differential pressure sensor assembly.


b.

Replace the exhaust manifold converter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/ DPF)>REMOVAL

NOTICE:

Perform the initialization procedure for "Catalyst Deterioration Learning Value Clear" and "DPF Deposition Value Clear".

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

d.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).



Result:
Proceed to
NEXT



NEXT

END