The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front air conditioning unit (for RHD) removal/installation are shown below.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
for Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION
for Type B:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION
for Type C:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for 7GR-FKS:
for 1GD-FTV:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
3. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
4.DRAIN ENGINE COOLANT
for 7GR-FKS:
for 1GD-FTV:
5.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
47220D
6.DISCONNECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
55738D
7.REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL
55701J
8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
88717A
9.DISCONNECT COOLER REFRIGERANT SUCTION PIPE A (w/o Sub-cool Accelerator)
|
Remove in this Direction |
Remove the bolt and rotate the 1-point tightening plate as shown in the illustration.
Disconnect the cooler refrigerant suction pipe A.
Remove the O-ring from the cooler refrigerant suction pipe A.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
88716A
10.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A (w/o Sub-cool Accelerator)
Disconnect the cooler refrigerant liquid pipe A.
Remove the O-ring from the cooler refrigerant liquid pipe A.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
88710C
11.DISCONNECT AIR CONDITIONING TUBE ASSEMBLY (w/ Sub-cool Accelerator)
|
Remove in this Direction |
Remove the bolt and rotate the 1-point tightening as shown in the illustration.
Disconnect the air conditioning tube assembly.
Remove the O-ring from the air conditioning tube assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
87246A
12.DISCONNECT HEATER WATER HOSE OUTLET A (for 1GD-FTV)
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water hose outlet A.
Do not apply excessive force to the water hose and heater water hose outlet A.
Prepare a drain pan or cloth in case the coolant leaks.
87245A
13.DISCONNECT HEATER WATER HOSE INLET A (for 1GD-FTV)
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water hose inlet A.
Do not apply excessive force to the water hose and heater water hose inlet A.
Prepare a drain pan or cloth in case the coolant leaks.
87245A
14.DISCONNECT HEATER WATER HOSE INLET A (for 7GR-FKS)
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water hose inlet A.
Do not apply excessive force to the water hose and heater water hose inlet A.
Prepare a drain pan or cloth in case the coolant leaks.
87246A
15.DISCONNECT HEATER WATER HOSE OUTLET A (for 7GR-FKS)
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water hose outlet A.
Do not apply excessive force to the water hose and heater water hose outlet A.
Prepare a drain pan or cloth in case the coolant leaks.
87128
16.REMOVE HEATER GROMMET
Detach the claw and remove the heater grommet.
17.REMOVE FRONT SEAT ASSEMBLY
for Power Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
for Separate Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Separate Seat Type)>REMOVAL
for Fixed Bench Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Fixed Bench Seat Type)>REMOVAL
for Sliding Bench Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Sliding Bench Seat Type)>REMOVAL
55301
18.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
19.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU
87211
20.REMOVE NO. 1 AIR DUCT
Remove the 2 bolts.
Detach the claw and remove the No. 1 air duct.
When removing, do not crack or deform the lower heater case of the air conditioning radiator assembly.
If the No. 1 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace with a new one.
87212G
21.REMOVE REAR NO. 3 AIR DUCT (w/ Rear Foot Duct)
|
Remove in this Direction |
Remove the rear No. 3 air duct as shown in the illustration.
87212F
22.REMOVE REAR NO. 2 AIR DUCT (w/ Rear Foot Duct)
for Wagon:
Detach the clamp.
|
Remove in this Direction |
Remove the rear No. 2 air duct as shown in the illustration.
45250
23.REMOVE STEERING COLUMN ASSEMBLY
33530K
24.REMOVE SHIFT LEVER ASSEMBLY (for Manual Transmission)
25.REMOVE TRANSMISSION INSTRUMENT PANEL SHIFT ASSEMBLY (for Automatic Transmission)
26.REMOVE OUTER LAP BELT ANCHOR COVER
for Wagon:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY (for Wagon)>REMOVAL
for Semi-trim:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY (for Semi-trim)>REMOVAL
for Full-trim:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY (for Full-trim)>REMOVAL
73220
27.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)
for Wagon:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY (for Wagon)>REMOVAL
for Semi-trim:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY (for Semi-trim)>REMOVAL
for Full-trim:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY (for Full-trim)>REMOVAL
73210
28.REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)
Use the same procedure described for the LH side.
74733
29.REMOVE NO. 1 HAND GRIP COVER (w/ Hand Rail)
74708
30.REMOVE NO. 2 HAND GRIP FRAME SUB-ASSEMBLY (w/ Hand Rail)
67918D
31.REMOVE REAR DOOR SCUFF PLATE LH
Use the same procedure described for the RH side.
for Wagon:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Wagon)>REMOVAL
for Semi-trim:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Semi-trim)>REMOVAL
for Full-trim:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL
74617A
32.REMOVE ASSIST GRIP PLUG (w/ Assist Grip)
Use the same procedure for both assist grip plugs.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL
74680
33.REMOVE PILLAR ASSIST GRIP ASSEMBLY B (w/ Assist Grip)
62414A
34.REMOVE LOWER CENTER PILLAR GARNISH LH
Use the same procedure described for the RH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL
67917C
35.REMOVE REAR DOOR SCUFF PLATE RH (for 5 Door)
except Wagon:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Semi-trim)>REMOVAL
for Wagon:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Wagon)>REMOVAL
62413A
36.REMOVE LOWER CENTER PILLAR GARNISH RH (for 5 Door)
67935
37.REMOVE BACK DOOR SCUFF PLATE (for 4 Door)
73570B
38.REMOVE REAR SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR) (for 4 Door, w/ Seat Belt)
Use the same procedure described for the LH side.
Click hereVehicle Interior>SEAT BELT>REAR SEAT OUTER BELT ASSEMBLY (for Full-trim)>REMOVAL
62630L
39.REMOVE REAR QUARTER TRIM BOARD ASSEMBLY RH (for 4 Door)
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL
62610K
40.REMOVE SIDE TRIM BOARD ASSEMBLY RH (for High Roof, for Full-trim)
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL
62510M
41.REMOVE QUARTER TRIM PANEL ASSEMBLY RH (for 4 Door)
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>REMOVAL
58510D
42.REMOVE FRONT FLOOR CARPET ASSEMBLY
w/ Console Box:
Using a clip remover, remove the 4 clips.
|
Fastener |
|
Remove in this Direction |
Detach each fastener.
Fold back the front floor carpet assembly as shown in the illustration.
w/o Console Box:
Using a clip remover, remove the 4 clips.
|
Fastener |
|
Remove in this Direction |
Detach each fastener.
Fold back the front floor carpet assembly as shown in the illustration.
58193G
43.REMOVE NO. 3 FRONT FLOOR FOOTREST
Using a clip remover, detach the clip and remove the No. 3 front floor footrest.
82141
44.DISCONNECT INSTRUMENT PANEL WIRE
Remove each bolt and each ground wire.
| *A | w/ PTC Heater | *B | w/ VFC ECU |
| *1 | Ground Wire | *2 | Protector Cover |
|
Connector |
|
Bolt |
|
Nut |
|
Remove in this Direction |
Detach the claw and open the protector cover.
Detach the claw and remove the protector cover together with the instrument panel wire.
Disconnect each connector and detach each clamp.
Remove the nut and then disconnect the instrument panel wire.
55950G
45.REMOVE DEFROSTER NOZZLE ASSEMBLY
Detach the claw and remove the defroster nozzle assembly.
87201A
46.REMOVE AIR DUCT SUB-ASSEMBLY
Remove the 2 nuts and air duct sub-assembly.
55306A
47.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
|
Bolt |
|
Nut |
Remove the 3 bolts, 2 nuts and No. 1 instrument panel brace sub-assembly.
55307C
48.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
|
Nut |
|
Bolt |
|
Screw |
Remove the nut and screw.
Remove the 2 bolts and No. 2 instrument panel brace sub-assembly.
88650N
49.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY
50.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY
Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
When disassembling the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
Be careful not to damage the internal components of the instrument panel reinforcement assembly with air conditioning unit assembly on the glass etc. Only perform removal after first taking the appropriate actions.
Do not allow the instrument panel reinforcement assembly with air conditioning unit assembly to strike the airbag ECU assembly. Doing so may damage the heater case, causing water leaks.
Disconnect the drain cooler hose.
Remove the nut.
for Automatic Transmission:
Remove the 8 bolts.
| *A | for Manual Transmission | - | - |
| *a | Engine Room Side | - | - |
|
Bolt A |
|
Bolt B |
for Manual Transmission:
Remove the 9 bolts.
Remove the instrument panel reinforcement assembly with air conditioner unit assembly.
Do not hold the air conditioning harness assembly. Otherwise, static electricity from the technician may damage the air conditioning harness assembly.
Do not hold the heater core or pipe of the heater radiator unit sub-assembly. Otherwise, the pipe may detach, the clamp may be damaged, or the crimped areas of the heater core and pipe of the heater radiator unit sub-assembly may be damaged, causing coolant to leak.
Do not hold the air conditioning radiator damper servo sub-assembly, blower damper servo sub-assembly or link. Otherwise, the servo motor may become misaligned, causing abnormal operation noise, temperature control defects, or air leaks due to sealing defects in the doors.
Do not hold the door. Doing so may cause air leaks due to closing defects resulting from excessive opening/closing. Also, keep the door free from oil and grease.
51.REMOVE AIR CONDITIONER UNIT ASSEMBLY
Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
When disassembling the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
Be careful not to damage the internal components of the instrument panel reinforcement assembly and air conditioning unit assembly on the glass etc. Only perform removal after first taking the appropriate actions.
Store the air conditioning unit assembly in a location free from sand and other foreign matter.
Remove the 4 bolts and air conditioner unit assembly from the instrument panel reinforcement assembly.
Do not hold the air conditioning harness assembly. Otherwise, static electricity from the technician may damage the air conditioning harness assembly.
Do not hold the heater core or pipe of the heater radiator unit sub-assembly. Otherwise, the pipe may detach, the clamp may be damaged, or the crimped areas of the heater core and pipe of the heater radiator unit sub-assembly may be damaged, causing coolant to leak.
Do not hold the air conditioning radiator damper servo sub-assembly, blower damper servo sub-assembly or link. Otherwise, the servo motor may become misaligned, causing abnormal operation noise, temperature control defects, or air leaks due to sealing defects in the doors.
Do not hold the door. Doing so may cause air leaks due to closing defects resulting from excessive opening/closing. Also, keep the door free from oil and grease.
51406A
52.REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)
Perform this procedure only when replacement of the No. 1 cooler unit drain hose and No. 2 cooler unit drain hose is necessary.
for 7GR-FKS:
Click hereEngine / Hybrid System>7GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
52618
53.REMOVE LOWER FRONT BUMPER ABSORBER
Perform this procedure only when replacement of the No. 1 cooler unit drain hose and No. 2 cooler unit drain hose is necessary.
for 7GR-FKS:
Click hereEngine / Hybrid System>7GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
51405A
54.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
Perform this procedure only when replacement of the No. 1 cooler unit drain hose and No. 2 cooler unit drain hose is necessary.
for 7GR-FKS:
Click hereEngine / Hybrid System>7GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
23300
55.REMOVE FUEL FILTER ASSEMBLY (for 1GD-FTV)
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT
Perform this procedure only when replacement of the No. 1 cooler unit drain hose and No. 2 cooler unit drain hose is necessary.
88539
56.REMOVE NO. 1 COOLER UNIT DRAIN HOSE
Perform this procedure only when replacement of the No. 1 cooler unit drain hose is necessary.
Disconnect the No. 1 cooler unit drain hose from cooler unit drain pipe.
|
Remove in this Direction |
Remove the No. 1 cooler unit drain hose.
Install the No. 1 cooler unit drain hose with its paint mark facing upward.
88539C
57.REMOVE NO. 2 COOLER UNIT DRAIN HOSE
Perform this procedure only when replacement of the No. 2 cooler unit drain hose is necessary.
Remove the bolt and detach the clamp.
Remove the No. 2 cooler unit drain hose together with the cooler unit drain pipe.
Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 2 cooler unit drain hose from cooler unit drain pipe.
88539D
58.REMOVE COOLER UNIT DRAIN PIPE
Perform this procedure only when replacement of the cooler unit drain pipe is necessary.
Remove the 2 screws and piping clamp.